Recent technical progress in sample preparation and liquid-phase separation-mass spectrometry for proteomic analysis of mass-limited samples

Solid-Phase Microextraction-Aided Capillary Zone Electrophoresis-Mass Spectrometry: Toward Bottom-Up Proteomics of Single Human Cells

Capillary zone electrophoresis-mass spectrometry (CZE-MS) has been recognized as a valuable technique for the proteomics of mass-limited biological samples (i.e., single cells). However, its broad adoption for single cell proteomics (SCP) of human cells has been impeded by the low sample loading capacity of CZE, only allowing us to use less than 5% of the available peptide material for each measurement. Here we present a reversed-phase-based solid-phase microextraction (RP-SPME)-CZE-MS platform to solve the issue, paving the way for SCP of human cells using CZE-MS. The RP-SPME-CZE system was constructed in one fused silica capillary with zero dead volume for connection via in situ synthesis of a frit, followed by packing C8 beads into the capillary to form a roughly 2 mm long SPME section. Peptides captured by SPME were eluted with a buffer containing 30% (v/v) acetonitrile and 50 mM ammonium acetate (pH 6.5), followed by dynamic pH junction-based CZE-MS. The SPME-CZE-MS enabled the injection of nearly 40% of the available peptide sample for each measurement. The system identified 257 ± 24 proteins and 523 ± 69 peptides (N = 2) using a Q-Exactive HF mass spectrometer when only 0.25 ng of a commercial HeLa cell digest was available in the sample vial and 0.1 ng of the sample was injected. The amount of available peptide is equivalent to the protein mass of one HeLa cell. The data indicate that SPME-CZE-MS is ready for SCP of human cells.

Top-Down Proteomics Analysis of Picogram-Level Complex Samples Using Spray-Capillary-Based Capillary Electrophoresis-Mass Spectrometry

Proteomics analysis of mass-limited samples has become increasingly important for understanding biological systems in physiologically relevant contexts such as patient samples, multicellular organoids, spheroids, and single cells. However, relatively low sensitivity in top-down proteomics methods makes their application to mass-limited samples challenging. Capillary electrophoresis (CE) has emerged as an ideal separation method for mass-limited samples due to its high separation resolution, ultralow detection limit, and minimal sample volume requirements. Recently, we developed "spray-capillary", an electrospray ionization (ESI)-assisted device, that is capable of quantitative ultralow-volume sampling (e.g., pL-nL level). Here, we developed a spray-capillary-CE-MS platform for ultrasensitive top-down proteomics analysis of intact proteins in mass-limited complex biological samples. Specifically, to improve the sensitivity of the spray-capillary platform, we incorporated a polyethylenimine (PEI)-coated capillary and optimized the spray-capillary inner diameter. Under optimized conditions, we successfully detected over 200 proteoforms from 50 pg of E. coli lysate. To our knowledge, the spray-capillary CE-MS platform developed here represents one of the most sensitive detection methods for top-down proteomics. Furthermore, in a proof-of-principle experiment, we detected 261 ± 65 and 174 ± 45 intact proteoforms from fewer than 50 HeLa and OVCAR-8 cells, respectively, by coupling nanodroplet-based sample preparation with our optimized CE-MS platform. Overall, our results demonstrate the capability of the modified spray-capillary CE-MS platform to perform top-down proteomics analysis on picogram amounts of samples. This advancement presents the possibility of meaningful top-down proteomics analysis of mass-limited samples down to the level of single mammalian cells.

Biological mass spectrometry enables spatiotemporal 'omics: From tissues to cells to organelles

Biological processes unfold across broad spatial and temporal dimensions, and measurement of the underlying molecular world is essential to their understanding. Interdisciplinary efforts advanced mass spectrometry (MS) into a tour de force for assessing virtually all levels of the molecular architecture, some in exquisite detection sensitivity and scalability in space-time. In this review, we offer vignettes of milestones in technology innovations that ushered sample collection and processing, chemical separation, ionization, and 'omics analyses to progressively finer resolutions in the realms of tissue biopsies and limited cell populations, single cells, and subcellular organelles. Also highlighted are methodologies that empowered the acquisition and analysis of multidimensional MS data sets to reveal proteomes, peptidomes, and metabolomes in ever-deepening coverage in these limited and dynamic specimens. In pursuit of richer knowledge of biological processes, we discuss efforts pioneering the integration of orthogonal approaches from molecular and functional studies, both within and beyond MS. With established and emerging community-wide efforts ensuring scientific rigor and reproducibility, spatiotemporal MS emerged as an exciting and powerful resource to study biological systems in space-time.

Deep Bottom-up Proteomics Enabled by the Integration of Liquid-Phase Ion Trap

In bottom-up proteomics, the complexity of the proteome requires advanced peptide separation and/or fractionation methods to acquire an in-depth understanding of protein profiles. Proposed earlier as a solution-phase ion manipulation device, liquid phase ion traps (LPITs) were used in front of mass spectrometers to accumulate target ions for improved detection sensitivity. In this work, an LPIT-reversed phase liquid chromatography-tandem mass spectrometry (LPIT-RPLC-MS/MS) platform was established for deep bottom-up proteomics. LPIT was used here as a robust and effective method for peptide fractionation, which also shows good reproducibility and sensitivity on both qualitative and quantitative levels. LPIT separates peptides based on their effective charges and hydrodynamic radii, which is orthogonal to that of RPLC. With excellent orthogonality, the integration of LPIT with RPLC-MS/MS could effectively increase the number of peptides and proteins being detected. When HeLa cells were analyzed, peptide and protein coverages were increased by ∼89.2% and 50.3%, respectively. With high efficiency and low cost, this LPIT-based peptide fraction method could potentially be used in routine deep bottom-up proteomics.

Bottom-Up Proteomics: Advancements in Sample Preparation

Liquid chromatography–tandem mass spectrometry (LC–MS/MS)-based proteomics is a powerful technique for profiling proteomes of cells, tissues, and body fluids. Typical bottom-up proteomic workflows consist of the following three major steps: sample preparation, LC–MS/MS analysis, and data analysis. LC–MS/MS and data analysis techniques have been intensively developed, whereas sample preparation, a laborious process, remains a difficult task and the main challenge in different applications. Sample preparation is a crucial stage that affects the overall efficiency of a proteomic study; however, it is prone to errors and has low reproducibility and throughput. In-solution digestion and filter-aided sample preparation are the typical and widely used methods. In the past decade, novel methods to improve and facilitate the entire sample preparation process or integrate sample preparation and fractionation have been reported to reduce time, increase throughput, and improve reproducibility. In this review, we have outlined the current methods used for sample preparation in proteomics, including on-membrane digestion, bead-based digestion, immobilized enzymatic digestion, and suspension trapping. Additionally, we have summarized and discussed current devices and methods for integrating different steps of sample preparation and peptide fractionation.

Comparison of Database Searching Programs for the Analysis of Single-Cell Proteomics Data

Single-cell proteomics is emerging as an important subfield in the proteomics and mass spectrometry communities, with potential to reshape our understanding of cell development, cell differentiation, disease diagnosis, and the development of new therapies. Compared with significant advancements in the "hardware" that is used in single-cell proteomics, there has been little work comparing the effects of using different "software" packages to analyze single-cell proteomics datasets. To this end, seven popular proteomics programs were compared here, applying them to search three single-cell proteomics datasets generated by three different platforms. The results suggest that MSGF+, MSFragger, and Proteome Discoverer are generally more efficient in maximizing protein identifications, that MaxQuant is better suited for the identification of low-abundance proteins, that MSFragger is superior in elucidating peptide modifications, and that Mascot and X!Tandem are better for analyzing long peptides. Furthermore, an experiment with different loading amounts was carried out to investigate changes in identification results and to explore areas in which single-cell proteomics data analysis may be improved in the future. We propose that this comparative study may provide insight for experts and beginners alike operating in the emerging subfield of single-cell proteomics.

An angled-shape tip-based strategy for highly sensitive proteomic profiling of a low number of cells

Profiling proteins plays an essential role in understanding the functions and dynamic networks in biological systems. Mass spectrometry-based proteomic analysis commonly requires multistep sample processing, which results in severe sample loss. Although the recently developed microproteomic strategies have substantially reduced sample loss via droplet microfluidic technology, specialized equipment and well-trained personnel are needed, which may limit their wide adoption. Here, we report an angled-shape tip-based strategy for rapid sample preparation and sensitive proteomic profiling of small cell populations (<1000 cells). The angled-shape tip provided a 'reactor' for the entire proteomic sample processing workflow, from cell capture and lysis to protein digestion, eliminating the sample transfer-induced protein loss. The angled-shape tip was surface-treated for anti-protein adsorption which further reduced the sample loss. Using this strategy, 1241 ± 38-4110 ± 37 protein groups and 4010 ± 700-34 879 ± 575 peptides were identified from 10-1000 HeLa cells with high quantification reproducibility in only 4.5 h sample processing time, which was superior to the reported methods and commercial kits, especially for <100 cells. This approach was easily accessible, straightforward to operate, and compatible with flow cytometry-based cell sorting. It showed great potential for in-depth proteomic profiling of rare cells (<1000 cells) in both basic biological research and clinical application.

Separation methods in single-cell proteomics: RPLC or CE?

Cellular heterogeneity is commonly investigated using single-cell genomics and transcriptomics to investigate biological questions such as disease mechanism, therapeutic screening, and genomic and transcriptomic diversity between cellular populations and subpopulations at the cellular level. Single-cell mass spectrometry (MS)-based proteomics enables the high-throughput examination of protein expression at the single-cell level with wide applicability, and with spatial and temporal resolution, applicable to the study of cellular development, disease, effect of treatment, etc. The study of single-cell proteomics has lagged behind genomics and transcriptomics largely because proteins from single-cell samples cannot be amplified as DNA and RNA can using well established techniques such as PCR. Therefore, analytical methods must be robust, reproducible, and sensitive enough to detect the very small amount of protein within a single cell. To this end, nearly every step of the proteomics process has been extensively altered and improved to facilitate the proteomics analysis of single cells including cell counting and sorting, lysis, protein digestion, sample cleanup, separation, MS data acquisition, and data analysis. Here, we have reviewed recent advances in single-cell protein separation using nano reversed phase liquid chromatography (nRPLC) and capillary electrophoresis (CE) to inform application driven selection of separation techniques in the laboratory setting.

A review of suspension trapping digestion method in bottom-up proteomics

The standard bottom-up proteomic workflow is comprised of sample preparation, data acquisition, and data analysis. While the latter two parts have made considerable advances in the last decade, sample preparation has remained an important challenge within the workflow due to the multi-step nature of complex biological samples, and still requires much development. Several sample preparation methods have been developed and used in the last two decades, including in-gel, in-solution, on-bead, filter-aided sample preparation, and suspension trapping, to improve reproducibility, efficiency, scalability, and reduce handling time of this process. One of the most recent methods developed and applied in proteomics studies in recent years is suspension trapping, which combines rapid detergent removal, reactor-type protein digestion, and peptide clean-up in a tip or spin column. Suspension trapping is a simple, rapid, and reproducible digestion method that can effectively handle proteins in low microgram or sub-microgram amounts. This review discusses the benefits of the suspension trapping digestion method in relation to its development and application in bottom-up proteomics studies. We also discuss recent applications of suspension trapping digestion to different sample types and the features of the suspension trapping digestion method compared with other sample preparation methods. This article is protected by copyright. All rights reserved.

Microanalysis of Brain Angiotensin Peptides Using Ultrasensitive Capillary Electrophoresis Trapped Ion Mobility Mass Spectrometry

While the role of the renin-angiotensin system (RAS) in peripheral circulation is well characterized, we still lack an in-depth understanding of its role within the brain. This knowledge gap is sustained by lacking technologies for trace-level angiotensin detection throughout tissues, such as the brain. To provide a bridging solution, we enhanced capillary electrophoresis (CE) nanoflow electrospray ionization (ESI) with large-volume sample stacking and employed trapped ion mobility time-of-flight (timsTOF) tandem HRMS detection. A dynamic pH junction helped stack approximately 10 times more of the sample than optimal using the field-amplified reference. In conjunction, the efficiency of ion generation was maximized by a cone-jet nanospray on a low sheath-flow tapered-tip nano-electrospray emitter. The platform provided additional peptide-dependent information, the collision cross section, to filter chemical noise and improve sequence identification and detection limits. The lower limit of detection reached sub-picomolar or ∼30 zmol (∼18,000 copies) level. All nine targeted angiotensin peptides in mouse tissue samples were detectable and quantifiable from the paraventricular nucleus (PVN) of the hypothalamus even after removal of circulatory blood components (perfusion). We anticipate CE-ESI with timsTOF HRMS to be broadly applicable for the ultrasensitive detection of brain peptidomes in pursuit of a better understanding of the brain.

Infrared Laser Ablation Microsampling for Small Volume Proteomics

Infrared (IR) laser ablation was used to remove localized tissue regions from which proteins were extracted and processed with a low volume sample preparation workflow for bottom-up proteomics by liquid chromatography tandem mass spectrometry (LC-MS/MS). A polytetrafluoroethylene (PTFE) coated glass slide with 2 mm diameter microwells was used to capture ablated rat brain tissue for in situ protein digestion with submicroliter solution volumes. The resulting peptides were analyzed with LC-MS/MS for protein identification and label-free quantification. The method was used to identify an average of 600, 1350, and 1900 proteins from ablation areas of 0.01, 0.04, and 0.1 mm², respectively, from a 50 μm thick rat brain tissue section. Differential proteomics of 0.01 mm² regions captured from cerebral cortex and corpus callosum was accomplished to demonstrate the capabilities of the approach.

Infrared Laser Ablation Microsampling with a Reflective Objective

A Schwarzschild reflective objective with a numerical aperture of 0.3 and working distance of 10 cm was used for laser ablation sampling of tissue for off-line mass spectrometry. The objective focused the laser to a diameter of 5 μm and produced 10 μm ablation spots on thin ink films and tissue sections. Rat brain tissue sections 50 μm thick were ablated in transmission geometry, and the ablated material was captured in a microcentrifuge tube containing solvent. Proteins from ablated tissue sections were quantified with a Bradford assay, which indicated that approximately 300 ng of protein was captured from a 1 mm² area of ablated tissue. Areas of tissue ranging from 0.01 to 1 mm² were ablated and captured for bottom-up proteomics. Proteins were extracted from the captured tissue and digested for liquid chromatography tandem mass spectrometry (LC-MS/MS) analysis for peptide and protein identification.

Fabrication of Co3O4 quantum dot incorporated polyacrylamide ethylene glycol dimethacrylate as a new fiber for solid phase microextraction and trace determination of organophosphorus pesticides in environmental water samples

In this paper, a novel solid phase microextraction fiber based on Co₃O₄ quantum dot incorporated polyacrylamide-co-ethylene glycol dimethacrylate followed by corona discharge ion mobility spectrometry is presented for the trace determination of organophosphorus pesticides in environmental water samples. Ion mobility spectrometry is a comparatively inexpensive, well-known, robust, and easy to operate analytical instrument. This combination would provide a low-cost, fast, selective, and sensitive quantitative system for detection of organophosphorus pesticides. In order to obtain the best extraction efficiency, the optimization of parameters affecting this method was carried out. After optimization, a solution pH of 7.0, extraction temperature of 60 °C, adsorption temperature of 260 °C, extraction time of 30 min, stirring speed of 750 rpm, and ionic strength of 10% w/w were obtained. Consequently, the presented method showed low limits of detection (0.3-0.6 ng mL^-1), excellent enrichment factors (PF = 221-263), good linearity (R² > 0.995), and repeatabilities (intra-day: 3.4 to 4.8%) and (inter-day: 4.7 to 6.1%). The reproducibility (RSD% of fiber to fiber) was also investigated by analyzing three as-prepared fibers under the same conditions and was found to be less than 7.6%. Finally, the developed fiber was used for determination of organophosphorus pesticides in the field samples.

Nanoparticle-Aided Nanoreactor for Nanoproteomics

Large-scale bottom-up proteomics of few even single cells is crucial for a better understanding of the roles played by cell-to-cell heterogeneity in disease and development. Novel proteomic methodologies with extremely high sensitivity are required for few even single-cell proteomics. Sample processing with high recovery and no contaminants is one key step. Here we developed a nanoparticle-aided nanoreactor for nanoproteomics (Nano3) technique for processing low-nanograms of mammalian cell proteins for proteome profiling. The Nano3 technique employed nanoparticles packed in a capillary channel to form a nanoreactor (≤30 nL) for concentrating, cleaning, and digesting proteins originally in a lysis buffer containing sodium dodecyl sulfate (SDS), followed by nanoRPLC-MS/MS analysis. The Nano3 method identified a 40-times higher number of proteins based on MS/MS from 2-ng mouse brain protein samples compared to the SP3 (single-pot solid-phase-enhanced sample preparation) method, which performed the sample processing using the nanoparticles in a 10 μL solution in an Eppendorf tube. The data indicates a drastically higher sample recovery of the Nano3 compared to the SP3 method for processing mass-limited proteome samples. In this pilot study, the Nano3 method was further applied in processing 10-1000 HeLa cells for bottom-up proteomics, producing 441 ± 263 (n = 4) (MS/MS) and 983 ± 292 (n = 4) [match between runs (MBR)+MS/MS] protein identifications from only 10 HeLa cells using a Q-Exactive HF mass spectrometer. The preliminary results render the Nano3 method a useful approach for processing few mammalian cells for proteome profiling.