Micro- and nanoplastic transfer in freezing saltwater: implications for their fate in polar waters

Distribution of microplastics between ice and water in aquatic systems: The influence of particle properties, salinity and freshwater characteristics

Microplastics (MPs) are an anthropogenic emerging pollutant, with global contamination of both marine and freshwater systems extensively documented. The interplay of MP particle properties and environmental conditions needs to be understood in order to assess the environmental fate and evaluate mitigation measures. In cold climate, ice formation has appeared to significantly affect the distribution of MPs, but so far, limited research is available comparing different aquatic systems, especially freshwater. Experiments often rely on artificial water and specific MP model particles. This study used laboratory tests to investigate the ice-water distribution of a variety of environmentally relevant MP particle types (PP, PE, PS and PVC fragments (25-1000 μm), PET fibers (average length 821 μm, diameter 15 μm)) across different water types, including artificial water of high and low salinity, as well as natural water from a lake and a treatment wetland. Overall, ice entrapment of MPs occurred in almost all tests, but the ice-water distribution of MPs differed across the different water types tested. Among the tests with artificial water, salinity clearly increased MP concentrations in the ice, but it cannot be resolved whether this is caused by increased buoyancy, changes in ice structure, or thermohaline convection during freezing. In the natural freshwater tests, the partition of MPs was shifted towards the ice compared to what was seen in the artificial freshwater. The influence of different types of dissolved and particulate substances in the different waters on MPs fate should be considered important and further explored. In this study, the higher content of suspended solids in the lake water might have enhanced MP settling to the bottom and thereby contributed to the absence of MPs in the ice of the lake test, compared to the wetland test with low suspended solids and considerably more MPs in the ice. Furthermore, the higher negative charge in the lake water possibly stabilized the negatively charged MPs in suspension, and reduced ice entrapment. Regarding particle properties, shape had a distinct effect, with fibers being less likely incorporated into ice than fragments. No fibers were found in freshwater ice. However, it became clear that ice entrapment of MPs depends on factors other than the particles' buoyancy based on density differences and particle size and shape alone.

Nanoplastics Distribution during Ice Formation: Insights into Natural Surface Water Freezing Conditions

The migration characteristics of nanoplastics (NPs) in the natural freezing process are complex and have attracted increasing attention in simulating natural freezing in recent years. However, simulated freezing conditions often fall short of replicating natural freezing processes, and studies on the vertical distribution of NPs remain inadequate. This study established a more realistic simulation of the natural freezing process in surface water by controlling both the air temperature (T1) and the water temperature (T2). Additionally, we introduced a new parameter, the local distribution coefficient (Kiw1), to compare with the effective distribution coefficient (Kiw2). The values of Kiw1 and Kiw2 for PS-500 nm were 0.18 and 0.21, respectively, at T1 = -20 °C and T2 = 1 °C. The results revealed the NPs concentration differed in ice, near-ice liquid, and far-ice liquid. Both properties of NPs and environmental factors could regulate the vertical distribution of NPs. The findings underscored the importance of freezing temperature regulated by T1 and T2, elucidating the roles of various influencing factors on the vertical distribution characteristics of NPs and unraveling the mechanisms of NPs distribution in the ice-water system. This study can provide valuable insights for understanding the migration of NPs in surface water in cold regions.

Revealing the Freezing-Induced Alteration in Microplastic Behavior and Its Implication for the Microplastics Released from Seasonal Ice

Ice can serve as a significant temporary repository and conveyance mechanism for microplastics (MPs). MPs present in the water column can become entrapped within developing ice formations, subsequently being sequestered and transported by ice floes. With changing temperatures, MPs stored in ice can be released back into the environment, while freezing conditions can alter the properties of MPs, ultimately affecting the fate of MPs in the environment. Freezing of MPs in freshwater ice results in the aggregation of MP particles due to physical compression, leading to an increase in particle size once the MPs are released from the ice. The freezing-induced aggregation enhances buoyancy effects, accelerating the settling/rising velocity of MPs in water. Additionally, freezing can lead to enhanced surface wetting alterations, thus improving the dispersion of hydrophobic MPs. The presence of salt in the water can mitigate the effect of freezing on MPs due to the formation of a brine network within the ice structure, which reduces the pressure on MPs entrapped by ice. In cold regions, numerous MPs undergo freezing and thawing, re-entering the water column.

Nanoplastics in Water: Artificial Intelligence-Assisted 4D Physicochemical Characterization and Rapid In Situ Detection

For the first time, we present a much-needed technology for the in situ and real-time detection of nanoplastics in aquatic systems. We show an artificial intelligence-assisted nanodigital in-line holographic microscopy (AI-assisted nano-DIHM) that automatically classifies nano- and microplastics simultaneously from nonplastic particles within milliseconds in stationary and dynamic natural waters, without sample preparation. AI-assisted nano-DIHM identifies 2 and 1% of waterborne particles as nano/microplastics in Lake Ontario and the Saint Lawrence River, respectively. Nano-DIHM provides physicochemical properties of single particles or clusters of nano/microplastics, including size, shape, optical phase, perimeter, surface area, roughness, and edge gradient. It distinguishes nano/microplastics from mixtures of organics, inorganics, biological particles, and coated heterogeneous clusters. This technology allows 4D tracking and 3D structural and spatial study of waterborne nano/microplastics. Independent transmission electron microscopy, mass spectrometry, and nanoparticle tracking analysis validates nano-DIHM data. Complementary modeling demonstrates nano- and microplastics have significantly distinct distribution patterns in water, which affect their transport and fate, rendering nano-DIHM a powerful tool for accurate nano/microplastic life-cycle analysis and hotspot remediation.

The Role of Life Stages in the Sensitivity of Hediste diversicolor to Nanoplastics: A Case Study with Poly(Methyl)Methacrylate (PMMA)

The presence of plastic particles in oceans has been recognized as a major environmental concern. The decrease in particle size increases their ability to directly interact with biota, with particles in the nanometer size range (nanoplastics-NPs) displaying a higher ability to penetrate biological membranes, which increases with the decrease in particle size. This study aimed to evaluate the role of life stages in the effects of poly(methyl)methacrylate (PMMA) NPs on the polychaete Hediste diversicolor, a key species in the marine food web and nutrient cycle. Thus, behavioral (burrowing activity in clean and spiked sediment) and biochemical endpoints (neurotransmission, energy reserves, antioxidant defenses, and oxidative damage) were assessed in juvenile and adult organisms after 10 days of exposure to spiked sediment (between 0.5 and 128 mg PMMA NPs/Kg sediment). Overall, the results show that H. diversicolor is sensitive to the presence of PMMA NPs. In juveniles, exposed organisms took longer to burrow in sediment, with significant differences from the controls being observed at all tested concentrations when the test was performed with clean sediment, whereas in PMMA NP-spiked sediment, effects were only found at the concentrations 8, 32, and 128 mg PMMA NPs/Kg sediment. Adults displayed lower sensitivity, with differences to controls being found, for both sediment types, at 8, 32, and 128 mg PMMA NPs/Kg sediment. In terms of Acetylcholinesterase, used as a marker of effects on neurotransmission, juveniles and adults displayed opposite trends, with exposed juveniles displaying increased activity (suggesting apoptosis), whereas in adults, overall decreased activity was found. Energy-related parameters revealed a generally similar pattern (increase in exposed organisms) and higher sensitivity in juveniles (significant effects even at the lower concentrations). NPs also demonstrated the ability to increase antioxidant defenses (higher in juveniles), with oxidative damage only being found in terms of protein carbonylation (all tested NPs conditions) in juveniles. Overall, the data reveal the potential of PMMA NPs to affect behavior and induce toxic effects in H. diversicolor, with greater effects in juveniles.

Effects and applications of surfactants on the release, removal, fate, and transport of microplastics in aquatic ecosystem: a review

Microplastics (MPs) and surfactants (STs) are emerging pollutants in the environment. While many studies have focused on the interactions of STs with MPs, there has not been a comprehensive review focusing on the effect of STs on MPs in aquatic ecosystems. This review summarizes methods for removal of MPs from wastewater (e.g., filtration, flotation, coagulation/flocculation, adsorption, and oxidation-reduction) and the interactions and effects of STs with MPs (adsorption, co-adsorption, desorption, and toxicity). STs can modify MPs surface properties and influence their removal using different wastewater treatments, as well as the adsorption-desorption of both organic and inorganic chemicals. The concentration of STs is a crucial factor that impacts the removal or adsorption of pollutants onto MPs. At low concentrations, STs tend to facilitate MPs removal by flotation and enhance the adsorption of pollutants onto MPs. High ST concentrations, mainly above the critical micelle concentrations, cause MPs to become dispersed and difficult to remove from water while also reducing the adsorption of pollutants by MPs. Excess STs form emulsions with the pollutants, leading to electrostatic repulsion between MPs/STs and the pollutant/STs. As for the toxicity of MPs, the addition of STs to MPs shows complicated results, with some cases showing an increase in toxicity, some showing a decrease, and some showing no effect.

Identification of the driving factors of microplastic load and morphology in estuaries for improving monitoring and management strategies: A global meta-analysis

Estuaries are one of the primary pathways for transferring microplastics (MPs) from the land to the ocean. A comprehensive understanding of the load, morphological characteristics, driving factors, and potential risks of MPs in estuaries is imperative to inform reliable management in this critical transboundary area. Extracted from 135 publications, a global meta-analysis comprising 1477 observations and 124 estuaries was conducted. MP abundance in estuaries was tremendously variable, reaching a mean of 21,342.43 ± 122,557.53 items/m3 in water and 1312.79 ± 6295.73 items/kg in sediment. Fibers and fragments take up a majority proportion in estuaries. Polyester, polypropylene, and polyethylene are the most detected MP types. Around 68.73% and 85.51% of MPs detected in water and sediment are smaller than 1 μm. The redundancy analysis revealed that the explanatory factors influencing the morphological characteristics of MPs differed between water and sediment. Regression analysis shows that MP abundance in water is significantly inversely correlated with mesh/filter size, per capita plastic waste, and the Human Development Index, whereas it is significantly positively correlated with population density and share of global mismanaged plastic waste. MP abundance in sediment significantly positively correlated with aridity index and probability of plastic entering the ocean, while significantly negatively correlated with mesh/filter size. Analysis based on Geodector identified that the extraction method, density of flotation fluid, and sampling depth are the top three explanatory factors for MP abundance in water, while the share of global mismanaged plastic waste, the probability of plastic being emitted into the ocean, and population density are the top three explanatory factors for MP abundance in sediment. In the studied estuaries, 46.75% of the water and 2.74% of the sediment are categorized into extremely high levels of pollution, while 73.08% of the water and 43.48% of the sediment belong to class V of the potential ecological index.

Entrainment and Enrichment of Microplastics in Ice Formation Processes: Implications for the Transport of Microplastics in Cold Regions

Sea ice can serve as a temporary sink for microplastics (MPs), and thus, it too can function as a secondary source of and transport medium for MPs. This study aimed to explore the effect of various MP properties and environmental characteristics on the entrainment and enrichment of MPs in ice under varying turbulence conditions. It was found that high rotation speed in freshwater distinctively enhanced the entrainment of hydrophobic MPs in ice, this being attributable to the combined effects of frazil ice and air bubbles. The hydrophobic nature of these MPs caused them to be attracted to the water/air or water/ice interface. However, in saline water, high turbulence inhibited the entrainment of all of the MP types under study. The ice crystals formed a loose structure in saline water instead of congealing, and this allowed the exchange of MPs between ice and water, leading to the rapid expulsion of MPs from the ice. The enrichment factors of all the MPs under study increased in calm saline water compared to in calm freshwater. The results revealed that the entrainment and enrichment of MPs in ice can be critical pathways affecting their fate in cold regions.

Microplastic Interactions and Possible Combined Biological Effects in Antarctic Marine Ecosystems

Antarctica and the Southern Ocean are the most remote regions on Earth, and their quite pristine environmental conditions are increasingly threatened by local scientific, tourism and fishing activities and long-range transport of persistent anthropogenic contaminants from lower latitudes. Plastic debris has become one of the most pervasive and ubiquitous synthetic wastes in the global environment, and even at some coastal Antarctic sites it is the most common and enduring evidence of past and recent human activities. Despite the growing scientific interest in the occurrence of microplastics (MPs) in the Antarctic environment, the lack of standardized methodologies for the collection, analysis and assessment of sample contamination in the field and in the lab does not allow us to establish their bioavailability and potential impact. Overall, most of the Southern Ocean appears to be little-affected by plastic contamination, with the exception of some coastal marine ecosystems impacted by wastewater from scientific stations and tourist vessels or by local fishing activities. Microplastics have been detected in sediments, benthic organisms, Antarctic krill and fish, but there is no clear evidence of their transfer to seabirds and marine mammals. Therefore, we suggest directing future research towards standardization of methodologies, focusing attention on nanoplastics (which probably represent the greatest biological risks) and considering the interactions of MPs with macro- and microalgae (especially sea-ice algae) and the formation of epiplastic communities. In coastal ecosystems directly impacted by human activities, the combined exposure to paint chips, metals, persistent organic pollutants (POPs), contaminants of emerging interest (CEI) and pathogenic microorganisms represents a potential danger for marine organisms. Moreover, the Southern Ocean is very sensitive to water acidification and has shown a remarkable decrease in sea-ice formation in recent years. These climate-related stresses could reduce the resilience of Antarctic marine organisms, increasing the impact of anthropogenic contaminants and pathogenic microorganisms.

The interaction of micro/nano plastics and the environment: Effects of ecological corona on the toxicity to aquatic organisms

Concerns about the micro/nano plastics (MNPs) exposure risks have risen in recent years. The ecological corona (EC), which is generated by the interaction between MNPs and environmental substances, has a significant impact on their environmental fate and ecological risks. As the largest sink of MNPs, the aquatic environment is of great significance for understanding the environmental behaviour of MNPs. Transmission Electron Microscope (TME), Fourier Transform Infra-Red (FTIR), Scanning Electron Microscope (SEM), Dynamic Light Scattering (DLS) and other analytical methods have been used as effective methods to analyse the formation process of EC and detect the existing EC directly or indirectly on the surface of MNPs. The physicochemical properties of MNPs, complex aquatic environments and ageing time have been identified as the key factors affecting EC formation in aquatic environments. Moreover, the EC absorbed on MNPs significantly changed their environmental behaviour and toxicity to aquatic organisms. This review gives a full understanding of the EC formation progress on the surface of MNPs and different analytical methods for EC have been summarised which can further assist the ecological risk assessment of MNPs in the aquatic environment.

Impact of microplastics from polyethylene and biodegradable mulch films on rice (Oryza sativa L.)

Extensive use of plastic film mulch has resulted in accumulation of a large amount of residual plastic, which will eventually fragment into microplastics in agricultural soils. However, it is unclear how microplastics from plastic mulch film affect crops. To address this issue, rice plants exposed to microplastics derived from poly(butyleneadipate-co-terephthalate) (PBAT)-based biodegradable mulch film (BM) and polyethylene (PE) mulch film (PM) were investigated for plant growth, physio-biochemical processes, and gene expressions. Both types of microplastics significantly reduced the height and dry weight of rice plant. Oxidative stress was induced by microplastics in rice shoot and root, with levels of ROS relatively higher under treatment PM than that under treatment BM. Transcriptomic data showed that more genes were down-regulated by treatment PM than that by treatment BM. Genes encoding ammonium and nitrate transporters were down-regulated by both types of microplastics in rice roots at vegetative stage, whereas up-regulated at reproductive stage, as compared to their respective treatment with no microplastics (CK). Similar results regarding phenylpropanoid biosynthesis pathway and lignin content were also observed in rice roots. Net photosynthetic rate and SPAD value were significantly inhibited by treatments BM and PM in rice shoot, and the expression of genes involved in light reaction was reduced at vegetative stage, whereas there were no differences of them at reproductive stage, as compared to their respective treatment CK. Our study suggests that microplastics from BM and PM both affect the growth of rice plants via nitrogen metabolism and photosynthesis. The negative effects imposed by both types of microplastics on rice plant can be mitigated with the growth of plants, and the negative effects of microplastics from PE mulch film on rice plant are relatively stronger than that from the PBAT-based biodegradable film.