Photocatalytic polymer nanomaterials for the production of high value compounds

Tunable Photocatalytic Selectivity by Altering the Active Center Microenvironment of an Organic Polymer Photocatalyst

The favored production of one product over another is a major challenge in synthetic chemistry, reducing the formation of byproducts and enhancing atom efficacy. The formation of catalytic species that have differing reactivities based on the substrate being converted, has been targeted to selectively control reactions. Here, we report the production of photocatalytic self-assembled amphiphilic polymers, with either hydrophilic or hydrophobic microenvironments at the reactive center. Benzothiadiazole-based photocatalysts were polymerized into either the hydrophilic or the hydrophobic compartment of a diblock copolymer by RAFT polymerization. The difference in the reactivity of each microenvironment was dictated by the physical properties of the substrate. Stark differences in reactivity were observed for polar substrates, where a hydrophilic microenvironment was favored. Conversely, both microenvironments performed similarly for very hydrophobic substrates, showing that reagent partitioning is not the only factor that drives photocatalytic conversion. Furthermore, the use of secondary swelling solvents allowed an additional reagent exchange between the continuous phase and the heterogeneous photocatalyst, resulting in a significant 5-fold increase in conversion for a radical carbon-carbon coupling.

Catalytic Ozonation of Norfloxacin Using Co-Mn/CeO2 as a Multi-Component Composite Catalyst

In this study, a Co-Mn/CeO2 composite was prepared through a facile sol-gel method and used as an efficient catalyst for the ozonation of norfloxacin (NOR). The Co-Mn/CeO2 composite was characterized via XRD, SEM, BET and XPS analysis. The catalytic ozonation of NOR by Co-Mn/CeO2 under different conditions was systematically investigated, including the effect of the initial solution’s pH, Co-Mn/CeO2 composite dose, O3 dose and NOR concentration on degradation kinetics. Only about 3.33% of total organic carbon (TOC) and 72.17% of NOR could be removed within 150 min by single ozonation under the conditions of 60 mg/L of NOR and 200 mL/min of O3 at pH= 7 and room temperature, whereas in the presence of 0.60 g/L of the Co-Mn/CeO2 composite under the same conditions, 87.24% NOR removal was obtained through the catalytic ozonation process. The results showed that catalytic ozonation with the Co-Mn/CeO2 composite could effectively enhance the degradation and mineralization of NOR compared to a single ozonation system alone. The catalytic performance of CeO2 was significantly improved by the modification with Mn and Co. Co-Mn/CeO2 represents a promising way to prepare efficient catalysts for the catalytic ozonation of organic polluted water. The removal efficiency of NOR in five cycles indicates that Co-Mn/CeO2 is stable and recyclable for catalytic ozonation in water treatment.

Hairy Conjugated Microporous Polymer Nanoparticles Facilitate Heterogeneous Photoredox Catalysis with Solvent-Specific Dispersibility

Substrate accessibility is a key limiting factor for the efficiency of heterogeneous photoredox catalysis. Recently, a high photoactive surface area of conjugated microporous polymer nanoparticles (CMP NPs) has made them promising candidates for overcoming the mass transfer limitation to achieve high photocatalytic efficiency. However, this potential has not been realized due to limited dispersibility of CMP NPs in many solvents, particularly in water. Here, we report a polymer grafting strategy that furnishes versatile hairy CMP NPs with enhanced solvent-specific dispersibility. The method associates hundreds of solvent-miscible repeating units with one chain end of the photocatalyst surface, allowing minimal modification to the CMP network that preserves its photocatalytic activity. Therefore, the enhanced dispersibility of hairy CMP NPs in organic solvents or aqueous solutions affords high efficiency in various photocatalytic organic transformations.

MoS2-Cu/CuO@graphene Heterogeneous Photocatalysis for Enhanced Photocatalytic Degradation of MB from Water

The industrial revolution resulted in the contamination of natural water resources. Therefore, it is necessary to save and recover the natural water resources. In this regard, polymer-based composites have attracted the scientific community for their application in wastewater treatment. Herein, molybdenum disulfide composites with a mix phase of copper, copper oxide and graphene (MoS₂-Cu/CuO@GN) were synthesized through the hydrothermal method. Methylene blue (MB) was degraded by around 93.8% within the 30 min in the presence of MoS₂-Cu/CuO@GN under visible light. The degradation efficiency was further enhanced to 98.5% with the addition of H₂O₂ as a catalyst. The photocatalytic degradation efficiency of pure MoS₂, MoS₂-Cu/CuO and MoS₂-Cu/CuO@GN were also investigated under the same experimental conditions. The structural analysis endorses the presence of the Cu/CuO dual phase in MoS₂. The charge recombination ratio and band gap of MoS₂-Cu/CuO@GN were also investigated in comparison to pure MoS₂ and MoS₂-Cu/CuO. The chemical states, the analysis of C1s, O1s, Mo3d and Cu2p3, were also analyzed to explore the possible interaction among the present elements. The surface morphology confirms the existence of Cu/CuO and GN to MoS₂.

Singh A, Singh AK, Singh AK, Baeg JO, Gupta SK. Design of a graphitic carbon nitride catalytic–biocatalytic system for solar light-based CO2 production

We report that generating (formic acid) and regenerating (NADH/NADPH) from CO2 and NAD+/NADP+ using a nitrogen-rich polymeric carbon nitride catalytic–biocatalytic system under solar light (λ > 420 nm) could provide a new approach for storage of clean energy.