Uniform block copolymer nanofibers for the delivery of paclitaxel in 2D and 3D glioblastoma tumor models

Cancer treatment has transformed in recent years, with the introduction of immunotherapy providing substantial improvements in prognoses for certain cancers. However, traditional small molecule chemotherapeutics remain the major frontline of defence, and improving their delivery to solid tumors is of utmost importance for improving potency and reducing side effects. Here, length-controlled one-dimensional seed nanofibers (ca. 25 nm, ĐL = 1.05) were generated from poly(fluorenetrimethylenecarbonate)-block-poly(dimethylaminoethylmethacrylate) via living crystallization-driven self-assembly. Paclitaxel, with an encapsulation content ranging from 1 to 100 wt%, was loaded onto the preformed nanoparticles by solvent addition and evaporation. Drug loading was quantified by dynamic light scattering and transmission electron microscopy. Drug-loaded vectors were then incubated with U87 MG glioblastoma cells in a 2D cell assay for up to 72 h, and their anticancer properties were determined. It was observed that seed nanofibers loaded with 20 wt% paclitaxel were the most advantageous combination (IC50 = 0.48 μg mL-1), while pure seed nanofibers with no loaded drug displayed much lower cytotoxicity (IC50 = 11.52 μg mL-1). The IC50 of the loaded seed nanofibers rivaled that of the commercially approved Abraxane® (IC50 = 0.46 μg mL-1). 3D tumor spheroids were then cultured and subjected to the same stresses. Live/dead cell staining revealed that once more, seed nanofibers with 20 wt% paclitaxel, Abraxane®, and paclitaxel all exhibited similar levels of potency (55% viability), whereas control samples exhibited much higher cell viability (70%) after 3 days. These results demonstrate that nanofibers contain great potential as biocompatible drug delivery vehicles for cancer treatment as they exert a similar anticancer effect to the commercially available Abraxane®.

Role of Competitive Crystallization Kinetics in the Formation of 2D Platelets with Distinct Coronal Surface Patterns via Seeded Growth

Low dispersity 2D platelet micelles with controllable surface patterns were prepared by seeded-growth/living crystallization-driven self-assembly (CDSA) of block copolymer/homopolymer (BCP/HP) blends of poly(ferrocenyldimethylsilane)-b-poly(2-vinyl pyridine) (PFS-b-P2VP) and PFS. The precise morphology was found to be dependent on the proportion of the P2VP corona block, which can be efficiently controlled by changing the molar concentration ratio of PFS-b-P2VP/PFS, (c_B/c_H)_t, as well as their relative rates of crystallization, (G_B/G_H)_t. In the case where their molar concentration ratio was comparable to their crystallization rate ratio, platelets with a uniform distribution of P2VP coronal chains were formed. In other cases, as the concentration ratio increased (or decreased) during the living CDSA process, hierarchical structures were formed, including chain-like assemblies consisting of end-to-end linked rectangular platelets and fusiform (tapered) micelles. (G_B/G_H)_t was adjusted by tuning the degree of polymerization of the crystallizable PFS core-forming block and the BCP block ratio and by varying the terminus of the HP or changing the solvent used. Furthermore, the open edge of the platelets remained active for further growth, which permitted control of the morphology and dimensions of the platelets. Interestingly, in cases where the molar concentration ratio was lower than the crystallization rate ratio, growth rings were observed after two or more living CDSA steps. This study on the formation of platelet micelles by living CDSA of BCP/HP blends under kinetic control offers a considerable scope for the design of 2D polymer nanomaterials with controlled shape and surface patterns.

Exploring the "Living" Growth of Block Copolymer Nanofibers from Surface-Confined Seeds by In Situ Solution-Phase Atomic Force Microscopy

Living crystallization-driven self-assembly of polymeric and molecular amphiphiles is of growing interest as a seeded growth route to uniform 1D, 2D, and more complex micellar nanoparticles with controlled dimensions and a range of potential applications. Although most studies have been performed using colloidally stable seeds in bulk solution, growth of block copolymer (BCP) nanofibers from seeds confined to a surface is attracting increased attention. Herein, we have used atomic force microscopy (AFM) to undertake detailed studies of the growth of BCP nanofibers from immobilized seeds located on a Si surface. Through initial ex situ AFM studies and in situ AFM video analysis in solution, we determined that growth occurred in four stages, whereby an initial surface-bound growth regime transitions to surface-limited growth. As the nanofiber length increases, surface influence is diminished as the newly grown micelle segment is no longer bound to the Si substrate. Finally, a surface-independent regime occurs where nanofiber growth continues into bulk solution. In addition to the anticipated nanofiber elongation, our studies revealed occasional examples of AFM tip-induced core fragmentation. In these cases, the termini of the newly formed fragments were also active to further growth. Furthermore, unidirectional growth was detected in cases where the seed was oriented at a significant angle with respect to the surface, thereby restricting unimer access to one terminus.