New Ni(II)-Ni(II) Dinuclear Complex, a Resting State of the (α-diimine)NiBr2/AlMe3 Catalyst System for Ethylene Polymerization

A novel room-temperature stable diamagnetic nickel complex 2 was detected upon activation of Brookhart-type ethylene polymerization pre-catalyst LNiBr2 (1, L = 1,4-bis-2,4,6-trimethylphenyl-2,3-dimethyl-1,4-diazabuta-1,3-diene) with AlMe3. Using in situ 1H, 2H, and 13C NMR spectroscopy, as well as DFT calculations, this species has been identified as an antiferromagnetically coupled homodinuclear complex [LNiII(μ-Me)(μ-CH2)NiIIL]+Br−. Its behavior in the reaction solution is characteristic of the resting state of nickel catalyzed ethylene polymerization.

Direct Synthesis of Partially Chain-Straightened Propylene Oligomers and P-MA Co-Oligomers Using Axially Flexible Shielded Iminopyridyl Palladium Complexes

In this study, a series of partially chain-straightened propylene oligomers and functional propylene−methyl acrylate (P-MA) co-oligomers were synthesized with 8-alkyl-iminopyridyl Pd(II) catalysts. The molecular weight and polar monomer incorporation ratio could be tuned by using Pd(II) catalysts with various 8-alkyl-naphthyl substituents (8-alkyl: H, Me, and n-Bu). In propylene oligomerization, all the 8-alkyl-iminopyridyl Pd(II) catalysts convert propylene to partially chain-straightened (119−136/1000 C) oligomers with low molecular weights (0.3−1.5 kg/mol). Among the catalysts, Pd1 with non-substituent (H) on the ligand showed the highest activity of 5.4 × 104 g/((mol of Pd) h), generating oligomers with the lowest molecular weight (Mn: 0.3 kg/mol). Moreover, polar-functionalized propylene-MA co-oligomers with very high incorporation ratios (22.8−36.5 mol %) could be obtained in the copolymerization using these 8-alkyl-iminopyridyl Pd(II) catalysts. Additionally, Pd1 exhibited the best performance in propylene-MA copolymerization as it displayed the highest MA incorporation ratio of up to 36.5 mol%. All the three catalysts are capable of generating partially chain-straightened P-MA co-oligomers and the activities decrease gradually while the molecular weight increases with the increasing steric hindrance of the alkyl substituent (H < Me < n-Bu). Compared to Pd4 with the rigid 8-aryl substituent, the flexible 8-alkyl-iminopyridyl Pd(II) catalysts (Pd1-3) not only showed much higher activities in the propylene oligomerization, but also yielded P-MA co-oligomers with significantly higher incorporation ratios in the propylene co-oligomerization.

Unsymmetrical Strategy on α-Diimine Nickel and Palladium Mediated Ethylene (Co)Polymerizations

Among various catalyst design strategies used in the α-diimine nickel(II) and palladium(II) catalyst systems, the unsymmetrical strategy is an effective and widely utilized method. In this contribution, unsymmetrical nickel and palladium α-diimine catalysts (Ipty/ⁱPr-Ni and Ipty/ⁱPr-Pd) derived from the dibenzobarrelene backbone were constructed via the combination of pentiptycenyl and diisopropylphenyl substituents, and investigated toward ethylene (co)polymerization. Both of these catalysts were capable of polymerizing ethylene in a broad temperature range of 0-120 °C, in which Ipty/ⁱPr-Ni could maintain activity in the level of 10⁶ g mol^-1 h^-1 even at 120 °C. The branching densities of polyethylenes generated by both nickel and palladium catalysts could be modulated by the reaction temperature. Compared with symmetrical Ipty-Ni and ⁱPr-Ni, Ipty/ⁱPr-Ni exhibited the highest activity, the highest polymer molecular weight, and the lowest branching density. In addition, Ipty/ⁱPr-Pd could produce copolymers of ethylene and methyl acrylate, with the polar monomer incorporating both on the main chain and the terminal of branches. Remarkably, the ratio of the in-chain and end-chain polar monomer incorporations could be modulated by varying the temperature.

Thermally Stable and Highly Efficient N,N,N-Cobalt Olefin Polymerization Catalysts Affixed with N-2,4-Bis(Dibenzosuberyl)-6-Fluorophenyl Groups

The cobalt(II) chloride N,N,N-pincer complexes, [2-{(2,4-(C15H13)2-6-FC6H2)N=CMe}-6-(ArN=CMe)C5H3N]CoCl2 (Ar = 2,6-Me2C6H3) (Co1), 2,6-Et2C6H3 (Co2), 2,6-i-Pr2C6H3 (Co3), 2,4,6-Me3C6H2 (Co4), 2,6-Et2-4-MeC6H2 (Co5), and [2,6-{(2,4-(C15H13)2-6-FC6H2)N=CMe}2C5H3N]CoCl2 (Co6), each containing at least one N-2,4-bis(dibenzosuberyl)-6-fluorophenyl group, were synthesized in good yield from their corresponding unsymmetrical (L1–L5) and symmetrical bis(imino)pyridines (L6). The molecular structures of Co1 and Co2 spotlighted their distorted square pyramidal geometries (τ5 value range: 0.23–0.29) and variations in steric hindrance offered by the dissimilar N-aryl groups. On activation with either MAO or MMAO, Co1–Co6 all displayed high activities for ethylene polymerization, with levels falling in the order: Co1 > Co4 > Co5 > Co2 > Co3 > Co6. Indeed, the least sterically hindered 2,6-dimethyl Co1 in combination with MAO exhibited a very high activity of 1.15 × 107 g PE mol−1 (Co) h−1 at the operating temperature of 70 °C, which dropped by only 15% at 80 °C and 43% at 90 °C. Vinyl-terminated polyethylenes of high linearity and narrow dispersity were generated by all catalysts, with the most sterically hindered, Co3 and Co6, producing the highest molecular weight polymers [Mw range: 30.26–33.90 kg mol−1 (Co3) and 42.90–43.92 kg mol−1 (Co6)]. In comparison with structurally related cobalt catalysts, it was evident that the presence of the N-2,4-bis(dibenzosuberyl)-6-fluorophenyl groups had a limited effect on catalytic activity but a marked effect on thermal stability.