Biodiesel production from candlenut oil using a non-catalytic supercritical methanol transesterification process: optimization, kinetics, and thermodynamic studies

Biodiesel Production by Methanolysis of Rapeseed Oil-Influence of SiO2/Al2O3 Ratio in BEA Zeolite Structure on Physicochemical and Catalytic Properties of Zeolite Systems with Alkaline Earth Oxides (MgO, CaO, SrO)

Alkaline earth metal oxide (MgO, CaO, SrO) catalysts supported on BEA zeolite were prepared by a wet impregnation method and tested in the transesterification reaction of rapeseed oil with methanol towards the formation of biodiesel (FAMEs-fatty acid methyl esters). To assess the influence of the SiO2/Al2O3 ratio on the catalytic activity in the tested reaction, a BEA zeolite carrier material with different Si/Al ratios was used. The prepared catalysts were tested in the transesterification reaction at temperatures of 180 °C and 220 °C using a molar ratio of methanol/oil reagents of 9:1. The transesterification process was carried out for 2 h with the catalyst mass of 0.5 g. The oil conversion value and efficiency towards FAME formation were determined using the HPLC technique. The physicochemical properties of the catalysts were determined using the following research techniques: CO2-TPD, XRD, BET, FTIR, and SEM-EDS. The results of the catalytic activity showed that higher activity in the tested process was confirmed for the catalysts supported on the BEA zeolite characterized by the highest silica/alumina ratio for the reaction carried out at a temperature of 220 °C. The most active zeolite catalyst was the 10% CaO/BEA system (Si/Al = 300), which showed the highest triglyceride (TG) conversion of 90.5% and the second highest FAME yield of 94.6% in the transesterification reaction carried out at 220 °C. The high activity of this system is associated with its alkalinity, high value of the specific surface area, the size of the active phase crystallites, and its characteristic sorption properties in relation to methanol.

Engine Performance of High-Acid Oil-Biodiesel through Supercritical Transesterification

Relatively cheaper high-acid oil was used to make biodiesel through supercritical methanol transesterification, where high FFA contents in feedstock might conversely enhance the reaction extent. A direct-injection diesel engine and a dynamometer were used to analyze the engine characteristics of the high-acid oil-biodiesel. The experimental results show that the biodiesel made in this study had adequate fuel properties. This present biodiesel from high-acid oil was found to bear a lower heating value and equivalence ratio, with higher exhaust gas temperature, brake-specific fuel consumption (bsfc), and excess air ratio, than super-low sulfur diesel (SLSD). The biodiesel appeared to have larger-sized carbon residue left after the burning process in comparison with that of SLSD. The higher engine speed resulted in higher exhaust gas temperature and equivalence ratio, while lower bsfc, excess air ratio, was observed for the biodiesel. Supercritical methanol transesterification has been successfully proven to convert those low-cost feedstocks to renewable biodiesel products which own competitive engine performance in this study.

Comprehensive Characterization of Kukui Nuts as Feedstock for Energy Production in Hawaii

Fuel properties of oil-bearing kukui (Aleurites moluccana) nuts, a commonly found crop in Hawaii and tropical Pacific regions, were comprehensively studied to evaluate their potential for bioenergy production. Proximate and ultimate analyses, heating value, and elemental composition of the seed, shell, and de-oiled seed cake were determined across five sampling locations in Hawaii. The aged and freshly harvested kukui seeds were found to have similar oil contents, ranging from 61 to 64%wt. Aged seeds, however, have 2 orders of magnitude greater free fatty acids than those freshly harvested (50% vs 0.4%). The nitrogen content of the de-oiled kukui seed cake was found to be comparable to that of the soybean cake. Aging of kukui seeds can decrease the flashpoint temperature and increase the liquid-solid phase transition temperatures of kukui oil obtained. Mg and Ca are the major ash-forming elements present in the kukui shells, >80%wt of all metal elements detected, which may reduce deposition problems for thermochemical conversion in comparison with hazelnut, walnut, and almond shells. The study also revealed that kukui oil has similar characteristics to canola, indicating that it is well-suited for biofuel production.

Extraction of Municipal Sewage Sludge Lipids Using Supercritical CO2 for Biodiesel Production: Mathematical and Kinetics Modeling

Demand for determining renewable lipids feedstock for the production of biodiesel is increasing with the rapid depletion of petroleum diesel. The present study was conducted to assess the feasibility of utilizing municipal sewage sludge (MSS) as a potential lipids feedstock for biodiesel production. The lipids’ extraction and separation from MSS were conducted using supercritical CO2 (scCO2) with varying treatment time (15–120 min), temperature (30–80°C), pressure (10–50 MPa), and addition of cosolvents (1–10 wt.%). The modified Gompertz equation and Arrhenius equation were employed to evaluate lipids’ extraction and kinetics behavior from municipal sewage sludge using scCO2. About 27% of lipids were extracted from MSS with scCO2 at a temperature of 60°C, pressure of 30 MPa, treatment time of 60 min, and 5 wt.% of ethanol (EtOH) as cosolvent. The modified Gompertz equation was adequately fitted with experimental data of the lipids’ extraction from MSS using scCO2. The kinetics properties analyses revealed that the scCO2 extraction technology was highly dependent on pressure than the temperature for the extraction of the lipids from MSS. The physicochemical characteristics and fatty acid contents of the scCO2 extracted lipids from MSS and sewage sludge biodiesel were determined using a variety of analytical techniques. The physicochemical properties of the sewage sludge biodiesel were compared with the international standard specifications of biodiesel, such as the American Society for Testing and Materials specifications for diesel fuel (ASTM D6751) and European Standard (EN 14214) specifications.

Utilization of Polymeric Materials toward Sustainable Biodiesel Industry: A Recent Review

The biodiesel industry is expanding rapidly in accordance with the high energy demand and environmental deterioration related to the combustion of fossil fuel. However, poor physicochemical properties and the malperformance of biodiesel fuel still concern the researchers. In this flow, polymers were introduced in biodiesel industry to overcome such drawbacks. This paper reviewed the current utilizations of polymers in biodiesel industry. Hence, four utilizing approaches were discussed, namely polymeric biodiesel, polymeric catalysts, cold-flow improvers (CFIs), and stabilized exposure materials. Hydroxyalkanoates methyl ester (HAME) and hydroxybutyrate methyl ester (HBME) are known as polymeric biodiesel sourced from carbon-enriched polymers with the help of microbial activity. Based on the literature, the highest HBME yield was 70.7% obtained at 10% H2SO4 ratio in methanol, 67 °C, and 50 h. With increasing time to 60 h, HAME highest yield was reported as 68%. In addition, polymers offer wide range of esterification/transesterification catalysts. Based on the source, this review classified polymeric catalysts as chemically, naturally, and waste derived polymeric catalysts. Those catalysts proved efficiency, non-toxicity, economic feasibility, and reusability till the 10th cycle for some polymeric composites. Besides catalysis, polymers proved efficiency to enhance the biodiesel flow-properties. The best effect reported in this review was an 11 °C reduction for the pour point (PP) of canola biodiesel at 1 wt% of ethylene/vinyl acetate copolymers and cold filter plugging point (CFPP) of B20 waste oil biodiesel at 0.08 wt% of EVA copolymer. Polymeric CFIs have the capability to modify biodiesel agglomeration and facilitate flowing. Lastly, polymers are utilized for storage tanks and auto parts products in direct contact with biodiesel. This approach is completely exclusive for polymers that showed stability toward biodiesel exposure, such as polyoxymethylene (POM) that showed insignificant change during static immersion test for 98 days at 55 °C. Indeed, the introduction of polymers has expanded in the biodiesel industry to promote green chemistry.