Adhesion of fluid infused silicone elastomer to glass

Anisotropic Icephobic Mechanisms of Textured Surface: Barrier or Accelerator?

Icing has been seen as an economic and safety hazard due to its threats to aviation, power generation, offshore platforms, etc., where passive icephobic surfaces with a surface texturing design have the potential to address this problem. However, the intrinsic icephobic principles associated with the surface textures, energy, elasticity, and hybrid effects are still unclear. To explore the anisotropic wettability, ice nucleation, and ice detaching behaviors, a series of textured poly(dimethylsiloxane) (PDMS)-based coatings with various texture orientations were proposed through a simple stamping method with surface functionalization. The anisotropic hydrophobic/icephobic phenomena and mechanisms were discovered from wettability evaluation, experimentally studied by icing/deicing experiments, and finally verified by microscopic numerical simulations. One-way analysis of variance (one-way ANOVA analysis) was used to analyze the effect of surface textures on hydrophobic/icephobic properties, which assisted in understanding anisotropic phenomena. Typical anisotropic ice nucleation and growth on the textured coatings were clarified using in situ environmental scanning electron microscope (ESEM) characterization. The ice/coating interfacial stress responses were studied by numerical stimulation at the microscopic level, further verifying the localized, amplified, and propagated stress at the ice/coating interface. The theoretical anisotropic responses, barrier effect, and accelerating effect were verified to interpret the anisotropic wettability and icephobicity, depending on the specific surface conditions. This study revealed the basics of the anisotropic icephobic mechanisms of textured icephobic surfaces, further facilitating the R&D of passive icephobic surfaces.

Poroviscoelastic relaxations and rate-dependent adhesion in gelatin

Hydrogels, polymeric networks swollen with water, exhibit time/rate-dependent adhesion due to their poroviscoleastic constitution. In this study, we conducted probe-tack experiments on gelatin and investigated the influence of dwelling times and unloading rates on pull-off forces and work of adhesion. We utilized in situ contact imaging to monitor separation kinematics and interfacial crack velocities. We found that the crack velocities scaled nonlinearly with the unloading rate, in a power law with an exponent of 0.8 and were independent of dwelling time. At maximum unloading rates corresponding to subsonic interfacial crack speeds, we observed an order of magnitude enhancement in the apparent work of adhesion. The enhancement of adhesion and the crack velocities were related by a power law with an exponent of 0.39. The maximum vertical extension during unloading, a measure of crack opening, exhibited linear correlation with the enhancement of adhesion. Both correlations were in line with the rate-dependent work of fracture modeled for viscoelastic solids (e.g., Persson and Brener model). We explored the links between dwelling times corresponding to varying degrees of poroelastic diffusion and the adhesion. We found 40% additional enhancement in adhesion at the highest unloading rate. This enhancement is due to the unbalanced osmotic pressure, also known as the suction effect. The influence of dwelling times on adhesion was negligible for the interfacial cracks propagating slower than the diffusive time scales. These results identify viscoelastic relaxations as the dominant mechanism governing the rate-dependent enhancement of adhesion, and hence pave the way for tuning rate-dependent adhesion in soft multiphasic materials.

Adhesion and Contact Aging of Acrylic Pressure-Sensitive Adhesives to Swollen Elastomers

Fluid-infused (or swollen) elastomers are known for their antiadhesive properties. The presence of excess fluid at their surface is the main contributor to limiting contact formation and minimizing adhesion. Despite their potential, the mechanisms for adhesion and contact aging to fluid-infused elastomers are poorly understood beyond contact with a few materials (ice, biofilms, glass). This study reports on adhesion to a model fluid-infused elastomer, poly(dimethylsiloxane) (PDMS), swollen with silicone oil. The effects of oil saturation, contact time, and the opposing surface are investigated. Specifically, adhesion to two different adherents with comparable surface energies but drastically different mechanical properties is investigated: a glass surface and a soft viscoelastic acrylic pressure-sensitive adhesive film (PSA, modulus ∼25 kPa). Adhesion between the PSA and swollen PDMS [with 23% (w/w) silicone oil] retains up to 60% of its value compared to contact with unswollen (dry) PDMS. In contrast, adhesion to glass nearly vanishes in contact with the same swollen elastomer. Adhesion to the PSA also displays stronger contact aging than adhesion to glass. Contact aging with the PSA is comparable for dry and unsaturated PDMS. Moreover, load relaxation when the PSA is in contact with the PDMS does not correlate with contact aging for contact with the dry or unsaturated elastomer, suggesting that contact aging is likely caused by chain interpenetration and polymer reorganization within the contact region. Closer to full saturation of the PDMS with oil, adhesion to the PSA decreases significantly and shows a delay in the onset of contact aging that is weakly correlated to the poroelastic relaxation of the elastomer. Additional confocal imaging suggests that the presence of a layer of fluid trapped at the interface between the two solids could explain the delayed (and limited) contact aging to the oil-saturated PDMS.