Shear/peel bond strength of repositioned ceramic brackets

Mean Shearing Stroke Frequency of Orthodontic Brackets under Cycling Loading: An In Vitro Study

Based on the development of many adhesive systems and bonding techniques, bonding strength of orthodontic brackets has become even more important in modern clinical orthodontics. The aim of this study was to determine mean shearing stroke frequency of different orthodontic bracket types and bonding agents under cycling loading. Therefore, 10 different types of orthodontic bracket from 4 different brands were divided into 2 groups. Two different adhesives, namely Transbond™ XT etch-and-rinse for Group 1 and Transbond™ Plus self-etching-primer adhesive for Group 2 were considered. The brackets were tested under cycling loading force of 10-N and a crosshead speed of 300 mm/min and 40 cycle/min. The frequency of strokes that the brackets failed were determined and these data were analyzed by statistical analysis using an independent sample t-test and one-way analysis of variance (ANOVA). The level of significance was set at p < 0.05. Generally, differences between the frequency of shearing strokes of the bracket failures were found to be statistically significant depending on the type of adhesives and brackets (p < 0.05). The bonding technique for Group 1 was found to have a significantly higher shear bonding strength than Group 2. It is also seen that different types of bracket belonging to the same or different brands had different shear bonding strength. It may be concluded that: (i) all bracket types used in this study can be applied with both bonding techniques, (ii) in order to minimize the risk of hard tissue damage, ceramic brackets should be carefully bonded using the self-etching primary adhesive technique.

Enamel Resistance to Demineralization After Bracket Debonding Using Fluoride Varnish

The aim of this study was to evaluate the elemental content and morphology of enamel subjected to demineralization cycles after bracket debonding, adhesive remnant removal, and application of a fluoride varnish. 125 bovine teeth were divided into five groups (n = 25): 1) Intact enamel; 2) Intact enamel + demineralization cycles (DC); 3) Enamel after adhesive removal; 4)Enamel after adhesive removal + DC; 5) Enamel after adhesive removal + Profluorid + DC. The weight percentages of calcium (Ca), phosphorous (P) and fluoride (F) were calculated using energy dispersive X-ray spectroscopy (EDX). Samples were observed under scanning electron microscopy (SEM). Data were analyzed using Kruskal-Wallis and Mann-Whitney test. The weight percentages of Ca and P in Group 1 were significantly higher than Groups 2, 4, and 5. The weight percentages of Ca and P in Group 2 were significantly higher than Groups 4 and 5. Group 3 presented significantly higher percentages of Ca and P than Group 4. Group 5 showed a significantly higher percentage of Ca than Group 4. The presence of F was detected in Group 5. SEM images showed more signs of demineralization in Group 4 than Group 5. Fluoride varnish application may protect enamel from demineralization after bracket debonding.

Effect of Er:YAG Laser and Sandblasting in Recycling of Ceramic Brackets

Introduction: This study was performed to determine the shear bond strength of rebonded mechanically retentive ceramic brackets after recycling with Erbium-Doped Yttrium Aluminum Garnet (Er:YAG) laser or sandblasting. Methods: Twenty-eight debonded ceramic brackets plus 14 intact new ceramic brackets were used in this study. Debonded brackets were randomly divided into 2 groups of 14. One group was treated by Er:YAG laser and the other with sandblasting. All the specimens were randomly bonded to 42 intact human upper premolars. The shear bond strength of all specimens was determined with a universal testing machine at a crosshead speed of 0.5 mm/min until bond failure occurred. The recycled bracket base surfaces were observed under a scanning electron microscope (SEM). Analysis of variance (ANOVA) and Tukey tests were used to compare the shear bond strength of the 3 groups. Fisher exact test was used to evaluate the differences in adhesive remnant index (ARI) scores. Results: The highest bond strength belonged to brackets recycled by Sandblasting (16.83 MPa). There was no significant difference between the shear bond strength of laser and control groups. SEM photographs showed differences in 2 recycling methods. The laser recycled bracket appeared to have as well-cleaned base as the new bracket. Although the sandblasted bracket photographs showed no remnant adhesives, remarkable micro-roughening of the base of the bracket was apparent. Conclusion: According to the results of this study, both Er:YAG laser and sandblasting were efficient to mechanically recondition retentive ceramic brackets. Also, Er:YAG laser did not change the design of bracket base while removing the remnant adhesives which might encourage its application in clinical practice.

Analysis of Shear Bond Strength and Morphology of Er:YAG Laser-Recycled Ceramic Orthodontic Brackets

Objective. The aim of this study was to compare the recycling of deboned ceramic brackets via an Er:YAG laser or via the traditional chairside processing methods of flaming and sandblasting; shear bond strength and morphological changes were evaluated in recycled brackets versus new brackets. Materials and Methods. 3M Clarity Self-Ligating Ceramic Brackets with a microcrystalline base were divided into groups subjected to flaming, sandblasting, or exposure to an Er:YAG laser. New ceramic brackets served as a control group. Shear bond strengths were determined with an Electroforce test machine and tested for statistical significance through analysis of variance. Morphological examinations of the recycled ceramic bracket bases were conducted with scanning electron microscopy and confocal laser scanning microscopy. Residue on the bracket base was analyzed with Raman spectroscopy. Results. Faded, dark adhesive was left on recycled bracket bases processed via flaming. Adhesive was thoroughly removed by both sandblasting and exposure to an Er:YAG laser. Compared with new brackets, shear bond strength was lower after sandblasting (p < 0.05), but not after exposure to an Er:YAG laser. The Er:YAG laser caused no damage to the bracket. Conclusion. Er:YAG lasers effectively remove adhesive from the bases of ceramic brackets without damaging them; thus, this method may be preferred over other recycling methods.