Improvement of hydroxyapatite formation ability of titanium-based alloys by combination of acid etching and apatite nuclei precipitation

Development of Rapid Bioactivity-Expressed Zr-50Ti Alloys by Surface Treatment with Modified Simulated Body Fluid

Zr-50Ti alloys are promising biomaterials due to their excellent mechanical properties and low magnetic susceptibility. However, Zr-50Ti alloys do not inherently bond well with bone. This study aims to enhance the bioactivity and bonding strength of Zr-50Ti alloys for orthopedic implant materials. Initially, the surface of Zr-50Ti alloys was treated with a sulfuric acid solution to create a microporous structure, increasing surface roughness and area. Subsequently, low crystalline calcium phosphate (L-CaP) precipitation was controlled by adding Mg2+ and/or CO32- ions in modified simulated body fluid (m-SBF). The treated Zr-50Ti alloys were then subjected to cold isostatic pressing to force m-SBF into the micropores, followed by incubation to allow L-CaP formation. The apatite-forming process was tested in simulated body fluid (SBF). The results demonstrated that the incorporation of Mg2+ and/or CO32- ions enabled the L-CaP to cover the entire surface of Zr-50Ti alloys within only one day. After short-term soaking in SBF, the L-CaP layer, modulated by Mg2+ and/or CO32- ions, formed a uniform hydroxyapatite (HA) coating on the surface of the Zr-50Ti alloys, showing potential for optimized bone integration. After soaking in SBF for 14 days, the bonding strength between the apatite layer and alloy has the potential to meet the orthopedic application requirement of 22 MPa. This study demonstrates an effective method to enhance the bioactivity and bonding strength of Zr-50Ti alloys for orthopedic applications.

Development of Ti-10Nb alloy by powder metallurgy processing route for dental application

Titanium and its alloys are used to make dental implants because of its low density, high strength, and corrosion resistance. This paper describes the development of a potential biomaterial Ti-10Nb by powder metallurgy utilizing four different compaction pressures and analyses its microstructural, physical, mechanical, electrochemical, biological, and tribological behavior under various situations. The alloys were fabricated using four different compaction pressures, that is, 600, 650, 700, and 750 MPa, and sintered in a vacuum atmosphere at 1000°C for 1.5 h. The density of the samples was measured using Archimedes principle. X-ray diffraction and scanning electron microscopy equipped with energy dispersive spectroscopy were used to investigate the phase composition and microstructure, and a profilometer was used to examine the surface roughness of various samples. Vickers hardness tester was used to evaluate hardness, and a universal testing machine was used for compression testing. Corrosion and wear behavior were examined using a potentiostat and a Bio-Tribometer, respectively. This Ti-10Nb alloys consist of α + β phase, and have 16% highest porosity in sample compacted at 600 MPa. The samples compacted at 750 MPa achieved highest hardness, yield strength, compressive strength, and elastic modulus of 450 ± 29.72 HV, 718.22 ± 16.37 MPa, 1543.59 ± 24.37 MPa, and 41.27 ± 3.29 GPa, respectively. In addition, it also possesses highest corrosion and wear resistance with lowest icorr of 0.3954 ± 0.008 μA/cm2 and wear volume of (31.25 ± 0.206) × 10-3  mm3 . These results indicate that the developed alloys have a variety of desirable properties, including high hardness, adequate compressive strength, good corrosion and wear resistance, apatite-forming capability, and a low elastic modulus, which is advantageous for avoiding stress shielding. Therefore, it may be recommended to use it as a dental implant material.

A novel rapidly mineralized biphasic calcium phosphate with high acid-resistance stability for long-term treatment of dentin hypersensitivity

OBJECTIVES

Treating dental hypersensitivity (DH) rapidly and maintaining long-term effectiveness remains challenging. We aimed to address this problem by fabricating a novel rapidly mineralized biphasic calcium phosphate (RMBCP), which could rapidly elicit mineralization to form hydroxyapatite (HA) and perform excellent acid-resistant stability, thus effectively blocking the exposed dental tubules and protecting them from acid attack.

METHODS

RMBCP was firstly synthesized by precisely adjusting the molar ratio of acetic acid and calcium hydroxide and characterized by X-ray diffraction (XRD), X-ray fluorescence microprobe (XRF), Fourier-transform infrared (FTIR) spectrometer, scanning electron microscope (SEM), and transmission electron microscope (TEM). Subsequently, using a commercialized desensitizing agent, 45S5 bioglass (BG), as the control group, the mineralization performance of RMBCP was investigated in simulated body fluid (SBF), Dulbecco's modified eagle medium (DMEM), and even slightly acidic artificial saliva (pH=6.6). Moreover, the biocompatibility of RMBCP was studied. Finally, the tubule occlusion effect and acid-resistant stability of RMBCP were evaluated in vitro and in vivo.

RESULTS

The rapid mineralization behavior of RMBCP could easily adhere to the dentin surface and block the dentinal tubules completely in vitro and in vivo within 7days. RMBCP performed high acid-resistant stability to maintain the long-term therapeutic effect of DH treatment.

SIGNIFICANCE

Developing novel bioactive calcium phosphate materials with the ability to trigger mineralization for HA formation rapidly will be an effective strategy for the long-term treatment of dentin hypersensitivity.