Anatomic Locking Plate for Displaced Intraarticular Calcaneal Fracture: Design and Application

Clinical and radiological outcomes of internal fixation of complex talar neck and body fractures with locking plates through a dual approach

INTRODUCTION

Talar fractures are rare and surgical treatment has not been standardized. The literature is rather poor on preserving talar vascularization in single or dual approaches. A dual approach allows better exposure and should limit devascularization. Locking plates are one of the modern solutions for challenging comminuted fractures. The aim of this study was to determine clinical and radiological outcomes in complex talar fracture (CTF) of the neck and body, fixed by locking plates through a dual approach with at least one locking plate.

HYPOTHESIS

Locking-plate fixation of CTF through a dual approach leads to good clinical outcome.

MATERIAL AND METHODS

A single-center retrospective study included 12 cases of CTF treated between January 2007 and May 2019. 3D CT was systematically performed to plan surgery. A dual approach and at least one locking plate were used for fixation. Clinical outcome was evaluated on AOFAS score. Reduction quality and correlation to clinical results were evaluated, reduction with<2mm joint step being considered satisfactory. Consolidation rate and occurrence of avascular necrosis of the talus (ANT), post-traumatic arthritis (PTA) and postoperative complications were analyzed.

RESULTS

Mean follow-up was 27 months (range, 15-47). Mean AOFAS score was 70±18 (range, 30-97). Inframillimetric reduction was achieved in 67% of cases, without significant correlation with clinical results. The consolidation rate was 91.6%, ANT rate 18.2% and PTA rate 45.5%. One patient presented septic osteoarthritis secondary to scar necrosis.

CONCLUSION

Locking plate fixation of CTF through a dual approach provided acceptable clinical outcomes.

LEVEL OF EVIDENCE

IV; retrospective study.

Plating technique outcome evaluation in calcaneal fracture based on American orthopaedics foot and ankle score and Böhler-Gissane angle: A case series

Introduction

Intraarticular Calcaneal fracture treatment nowadays is still up for debate. Surgical plating treatment is favorable because of the rapid healing process and better anatomical reduction despite the invasive intervention. Hence, clinical evaluation is needed to assess the quality-of-life index from foot and ankle by the American orthopaedics Foot and Ankle Society (AOFAS) score postoperatively. Then, the outcome evaluation of reduction in calcaneal plating of intraarticular calcaneal fracture with Böhler angle and Gissane angle to see if the calcaneal plating technique is a recommended treatment for the calcaneal fracture.

Methods

We treated six patients from December 2020–July 2021 with a calcaneal fracture that underwent surgical plating, mainly by one surgeon. A calcaneal fracture is classified according to sanders classification. In this study, four patients are above the age of 40, and two are under 25. Pre-operative Böhler angle ranged from 8 to 65°, and Gissane angle ranged from 134 to 158°.

Outcomes

Surgical plating was performed on all six patients. From clinical evaluation using the AOFAS score, we got satisfactory results on all patients who underwent calcaneal plating surgery. Three patients achieved excellent range outcomes with 95% and 99% of AOFAS Scores, and three patients reported AOFAS score good range outcomes with the lowest score of 88%. From the radiological outcome, most of the patient's Böhler and Gissane angles achieved normal value after surgical plating.

Conclusion

The calcaneal plating technique gives better anatomical reduction depending on Bohler and Gissane angle. These results promise that anatomical reduction can improve clinical outcomes based on the AOFAS score. Thus, the plating method can be used effectively to treat an intraarticular calcaneal fracture.

•

Limited studies reported the outcome method of “Plating technique” surgery for calcaneal fracture.

•

Anatomical reduction achieved with Plating technique

•

Satisfactory clinical outcome was concluded after Plating technique surgery for calcaneal fracture.

[Study on sustentaculum tali screw placement for constant fragment of calcaneal fracture]

Objective

To investigate the anatomical characters of the sustentaculum tali (ST), accurate entry point and direction for the placement of ST screw from posterior subtalar joint facet to the constant fragment (CF) in calcaneal fractures.

Methods

A total of 100 patients with calcaneal fractures performed ankle CT scans were enrolled between January 2016 and April 2016. According to the inclusion criteria, the clinical data of 33 patients were analyzed, including 18 males and 15 females, with a median age of 41.0 years (range, 18-60 years). There were 16 cases on left side and 17 cases on the right side. Three-dimensional (3D) calcaneal model was reconstructed by Mimics 17.0 software, and the ST anatomical references were measured, including the length of upper and lower edge, the length and height of the midline, the horizontal angle between the midline and foot plantar surface. The parameters of the optimal entry point position (P' point) and placement angle of the ST screw were determined. The length of ST screw was also measured. The differences between males and females or left and right sides were compared.

Results

The length of upper edge of the ST was (16.60±2.23) mm, lower edge (20.65±2.90) mm, midline (20.56±2.62) mm, and the height of midline was (9.61±1.36) mm. The horizontal angle between the midline and foot plantar surface was (23.43±3.36)°. The vertical distance from P' point to the lowest point of the tarsal sinus was (3.09±1.65) mm, while the horizontal distance was (14.29±2.75) mm. The distance from P' point to the apex of the lateral talus, subchondral bone of subtalar joint, calcaneocuboid joint was (11.41±3.22), (6.59±2.22), (34.58±3.75) mm, respectively. The horizontal angle between the ST screw and foot plantar surface was (-1.17±2.07)°. The anteversion angle of ST screw was (16.18±2.05)° and the length was (41.64 ± 3.09) mm. There were significant differences in the length of upper and lower edge, the length and height of the midline, the distance from P' point to the apex of the lateral talus, subchondral bone of subtalar joint, and calcaneocuboid joint, and the anteversion angle and length of the ST screw between males and females ( P<0.05). There was no significant difference in above all parameters between left and right sides ( P>0.05).

Conclusion

After appropriate reduction of the calcaneal fractures, the entry point of ST screw was recommended at about 14 mm posterior and about 3 mm upper related to the foot horizontal line through the lowest tarsal sinus point; and the direction of ST screw placement was about 17° anteversion for males and 15° anteversion for females.