In vitro elution of gentamicin, amikacin, and ceftiofur from polymethylmethacrylate and hydroxyapatite cement

Sodium fusidate loaded apatitic calcium phosphates: Adsorption behavior, release kinetics, antibacterial efficacy, and cytotoxicity assessment

The present work reports the adsorption, release, antibacterial properties, and in vitro cytotoxicity of sodium fusidate (SF) associated with a carbonated calcium phosphate bone cement. The adsorption study of SF on cement powder compared to stoichiometric hydroxyapatite and nanocrystalline carbonated apatite was investigated to understand the interaction between this antibiotic and the calcium phosphate phases involved in the cement formulation and setting reaction. The adsorption data revealed a fast kinetic process. However, the evolution of the amount of adsorbed SF was well described by a Freundlich-type isotherm characterized by a low adsorption capacity of the materials toward the SF molecule. The in vitro release results indicated a prolonged and controlled SF release for up to 34 days. The SF amounts eluted daily were at a therapeutic level (0.5-2 mg/L) and close to the antibiotic minimum inhibitory concentration (0.1-0.9 mg/L). Furthermore, the release data fitting and modeling suggested that the drug release occurred mainly by a diffusion mechanism. The antibacterial activity showed the effectiveness of SF released from the formulated cements against Staphylococcus aureus. Furthermore, the biological in vitro study demonstrated that the tested cements didn't show any cytotoxicity towards human peripheral blood mononuclear cells and did not significantly induce inflammation markers like IL-8.

Can Amoxicillin and Clavulanic Acid Impregnated Plaster of Paris Beads Serve as an Effective Alternative to Systemic Antibiotics for Third Molar Surgeries? A Split Mouth Randomized Clinical Trial

Purpose

The present work was a pilot study undertaken to evaluate the effectiveness of amoxicillin and clavulanic acid impregnated plaster of paris beads for prevention of infection of third molar extraction sockets.

Materials and Methods

This was a prospective, randomized, split mouth clinical trial done on 16 patients (32 sites) who required surgical extraction of mandibular third molars. Control arm patients were given Tab. amoxicillin 500 mg with clavulanic acid 125 mg (Tab. Klavimed 625 mg, Indomed, India), thrice daily for 3 days after extraction, whereas test arm patients received Antibiotic Impregnated Microbeads (AIM), containing Amoxicillin 500 mg and Clavulanic Acid 100 mg placed in situ in the extraction socket. The primary outcome parameter was infection and the secondary outcome parameters were pain, trismus, swelling and wound healing.

Results

None of the patients in either group had post operative infection. There was no significant difference in pain intensity between the two groups (1st day p = 0.41; 3rd day p = 0.38, 7th day p = 0.37). Both the groups were also similar with respect to swelling (p = 0.596, 0.146, 0.871, 0.820 on 1st, 3rd, 7th, 15th post-op day ,respectively).

Conclusion

Amoxycillin with clavulanic acid impregnated PoP beads appears to be as effective as oral 3 day amoxicillin with clavulanic acid regime for prevention of 3 M socket infection.

Successful treatment of a chronic oroantral fistula infected with extensively drug resistant bacteria using long-term oesophageal tube feeding and several non-conventional treatments in a horse

BACKGROUND

Chronic oroantral fistulae (OAF) with secondary sinusitis can occur following repulsion of cheek teeth in horses.

CASE REPORT

An 8-year-old Andalusian cross gelding presented with an iatrogenic clinical crown fracture of tooth 209, which underwent repulsion of its apical portion (day 0). The horse was treated with intramuscular penicillin and intravenous gentamicin (5 days), followed by oral trimethoprim-sulphonamide (10 days) and then oral doxycycline (14 days). The acute iatrogenic OAF created during the initial repulsion persisted; a chronic OAF was identified on day 24. On day 48, septic sinusitis with multidrug-resistant (MDR) Escherichia coli was confirmed. Although susceptible to enrofloxacin in vitro, 30 days of therapy was unsuccessful. Subsequent serial cultures grew multiple MDR and extensively drug-resistant (XDR) gram-negative microorganisms. Whole-genome sequencing (WGS) revealed multiple sequence types of E. coli, with a range of resistance and virulence genes. The orientation of the OAF, regional osteomyelitis and septic sinusitis were confirmed with computed tomography on day 70. On day 74, enteral nutrition was provided through a cervical oesophagostomy tube for 3 months for prevention of oral feed contamination. The OAF was treated with various alternative therapeutics, including apple cider vinegar, propolis and amikacin impregnated products, until resolution on day 116.

CONCLUSION

These non-conventional therapeutics, antimicrobials and long-term oesophagostomy contributed to the successful treatment of a complicated OAF. In the future, WGS may be useful to inform antimicrobial selection when MDR or XDR organisms are identified.

Thermal Stability and in Vitro Elution Kinetics of Alternative Antibiotics in Polymethylmethacrylate (PMMA) Bone Cement

BACKGROUND

Amikacin, meropenem, minocycline, and fosfomycin have potential clinical utility for orthopaedic infections; however, their suitability for use in polymethylmethacrylate (PMMA) is poorly understood. The purpose of this study was (1) to quantify the thermal stability of these antibiotics at clinically relevant temperatures and (2) to determine the elution pharmacodynamics of these alternative antibiotics in vitro from PMMA beads of different sizes.

METHODS

Polymerization temperatures of 10-mm PMMA beads were measured over time to generate a simulated heating curve. Aqueous solutions of tobramycin, amikacin, meropenem, minocycline, and fosfomycin were subjected to the temperature curves, followed by incubation at 37°C. Minimum inhibitory concentrations of each antibiotic were evaluated against Staphylococcus aureus, Escherichia coli, and Acinetobacter baumannii. High-dose 4.5-mm, 6-mm, and 10-mm antibiotic-laden PMMA beads (10% antibiotic by weight) were submerged individually in a phosphate-buffered saline solution and incubated at 37°C. Antibiotic elution was determined with use of high-performance liquid chromatography with mass spectrometry.

RESULTS

Tobramycin, amikacin, and fosfomycin demonstrated thermal stability and maintained antimicrobial activity for 28 days. Minocycline and meropenem lost antimicrobial activity against all 3 organisms after 48 hours and 7 days, respectively. Elution concentrations, rates, and cumulative drug mass for tobramycin, amikacin, and meropenem were orders of magnitude higher than minocycline and fosfomycin at each time point.

CONCLUSIONS

This study identified notable differences in thermal stability and elution among antibiotics used to treat infections. Amikacin exhibited activity similarly to tobramycin. Meropenem demonstrated favorable elution kinetics and thermal stability in the initial 7-day period.

CLINICAL RELEVANCE

Amikacin and meropenem show pharmacologic promise as potential acceptable alternatives for local delivery in PMMA for treatment of orthopaedic infections. Further work to establish clinical relevance and utility is needed.

Safety and tolerability of liquid amikacin in antibiotic-loaded bone cement - a case series

High-dose liquid antibiotics are uncommon in bone cement. We present a case series of patients in which up to 16 mL of liquid amikacin (250 mg mL-1) was successfully incorporated into bone cement to treat periprosthetic joint infections. We did not observe adverse drug reactions definitively attributed to its use.

In vitro Elution of Penicillin, Ampicillin, Tetracycline, Tulathromycin, and Florfenicol From Plaster of Paris Beads

The objectives of this study were to report a recipe for making antibiotic impregnated Plaster of Paris (AI-PoP) beads using penicillin, ampicillin, tetracycline, tulathromycin, and florfenicol and to determine the in vitro elution rates of those antibiotics in the beads. The AI-PoP beads were made using Plaster of Paris powder, antibiotic, and water, cured for 24 h, sterilized by ethylene oxide, and stored up to 5 months before testing. For each antibiotic, 20 beads were combined with bovine serum in sterile tubes and incubated at 37°C on a rocker. Serum was replaced at intervals over the 14 days study period, and antibiotic concentrations were determined by high pressure liquid chromatography with mass spectrometry. Separately, in a proof-of-concept study, the growth of E. coli and T. pyogenes in eluent from 10 beads for each antibiotic was quantified by flow cytometry. Antibiotic was detected in AI-PoP bead eluent for 14 days for all but the ampicillin beads, for which antibiotic was detected for 8 days. The concentration of antibiotic in eluent was greater than the minimum inhibitory concentration (MIC) of tested bacteria for the entire study period for penicillin, tetracycline, tulathromycin, and florfenicol. The concentration of ampicillin remained greater than the MIC of E. coli for 4 days and T. pyogenes for 6 days. The colony forming units (CFU)/ml of live E. coli and T. pyogenes was reduced over a 72-h period by 1-3 log10 CFU, with the exception of tetracycline, which reduced CFU/ml of T. pyogenes by Collapse

Key Words

• Plaster of Paris
• antibiotics
• cattle
• elution
• wound infection

Collapse

MESH Headings Collapse

Grants Collapse

Affiliation(s)

Paul Merkatoris Department of Veterinary Diagnostic and Production Animal Medicine, College of Veterinary Medicine, Iowa State University, Ames, IA, United States
Jennifer Schleining Department of Large Animal Clinical Sciences, College of Veterinary Medicine & Biomedical Sciences, Texas A&M University, College Station, TX, United States
Adam Krull Department of Veterinary Diagnostic and Production Animal Medicine, College of Veterinary Medicine, Iowa State University, Ames, IA, United States
David Borts Department of Veterinary Diagnostic and Production Animal Medicine, College of Veterinary Medicine, Iowa State University, Ames, IA, United States
Virginia Fajt Department of Veterinary Physiology and Pharmacology, College of Veterinary Medicine & Biomedical Sciences, Texas A&M University, College Station, TX, United States

Collapse

In Vivo Release of Vancomycin from Calcium Phosphate Cement

Calcium phosphate cement (CPC) has good release efficiency and has therefore been used as a drug delivery system for postoperative infection. The release profile of CPC has mainly been evaluated by in vitro studies, which are carried out by immersing test specimens in a relatively large amount of solvent. However, it remains unclear whether antibiotic-impregnated CPC has sufficient clinical effects and release in vivo. We examined the in vivo release profile of CPC impregnated with vancomycin (VCM) and compared this with that of polymethylmethacrylate (PMMA) cement. To evaluate the release profile in vitro, the test specimens were immersed in 10 mL sterile phosphate-buffered saline per gram of test specimen and incubated at 37°C for 56 days in triplicate. For in vivo experiments, the test specimens were implanted between the fascia and muscle of the femur of rats. Residual VCM was extracted from the removed test specimens to determine the amount of VCM released into rat tissues. CPC released more VCM over a longer duration than PMMA in vitro. Released levels of VCM from CPC/VCM in vivo were 3.4-fold, 5.0-fold, and 8.6-fold greater on days 1, 7, and 28, respectively, than those released on the corresponding days from PMMA/VCM and were drastically greater on day 56 due to inefficient release from PMMA/VCM. The amount of VCM released from CPC and PMMA was much higher than the minimum inhibitory concentration (1.56 μg) and lower than the detection limit, respectively. Our findings suggest that CPC is a suitable material for releasing antibiotics for local action against established postoperative infection.

Surgical repair of thoraco-lumbar vertebral fracture-luxations in eight cats using screws and polymethylmethacrylate fixation

Objective: To report our clinical experience in the surgical treatment of feline thora-columbar vertebral fracture-luxations using optimal safe implantation corridors as previously described in vitro.

Study design: Retrospective clinical study.

Materials and Methods: Medical records and radiographs of cats with vertebral fracture- luxations stabilized by screws and polymethylmethacrylate (PMMA) using optimal safe implantation corridors between 2009 and 2011 were reviewed. For each patient the data included: signalment, cause of vertebral fracture-luxations, presence of concurrent injuries, pre- and postoperative neurological grade, surgical treatment, imaging findings, and clinical outcome with short-term (2 weeks) and long-term (12 months) follow-up.

Results: Eight cats with vertebral fracture-luxations involving the lumbar (L)(n = 5), the thoracic (T) spinal segments (n = 2), or the thoraco-lumbar junction (n = 1) were included in the study. Screws and PMMA were used bilaterally in five cats and unilaterally in three cats. No surgical intra-operative complications using the defined corridors were recorded. Implant failure followed by spontaneous recovery was recorded in one case. Two cats died in the postoperative period (≤4 days). The short-term and long-term clinical outcome was excellent in four out of eight cats and satisfactory in two out of eight cats.

Conclusion and Clinical relevance: This pilot study demonstrates the clinical applicability of optimal safe implantation corridors for stabilization of feline thoraco-lumbar vertebral fracture-luxations with screws and PMMA. This technique can be used with limited risks of iatrogenic injuries for stabilization of vertebral fracture-luxation localized between T11-L4.

A review of local antibiotic implants and applications to veterinary orthopaedic surgery

In the face of increasing incidence of multidrug resistant implant infections, local antibiotic modalities are receiving increased attention for both infection prophylaxis and treatment. Local antibiotic therapy that achieves very high antibiotic drug concentrations at the site of the implant may represent an avenue for treatment of biofilmforming bacterial pathogens. Randomized controlled trials in human patients have demonstrated an infection risk reduction when antibiotic-impregnated cement is used for infection prophylaxis in implanted joint prostheses, and when a gentamicin-impregnated collagen sponge is used for infection prophylaxis in midline sternotomy. The other modalities discussed have for the most part yet to be evaluated in randomized controlled trials in veterinary or human patients. In general, the in vivo pharmacokinetics and appropriate dosing profiles for local antibiotic modalities have yet to be elucidated. Toxicity is possible, and attention to the dose applied is warranted.

Surgical Treatment of Facial Abscesses and Facial Surgery in Pet Rabbits

Odontogenic facial abscesses associated with periapical infections and osteomyelitis of the jaw represent an important part of the acquired and progressive dental disease syndrome in pet rabbits. Complications such as retromasseteric and retrobulbar abscesses, extensive osteomyelitis of the mandible, and empyemas of the skull are possible sequelae. Standard and advanced diagnostic imaging should be pursued to make a detailed and proper diagnosis, and plan the most effective surgical treatment. This article reviews the surgical anatomy, the pathophysiology, and the classification of abscesses and empyemas of the mandible, the maxilla, and the skull. It also discusses surgical techniques for facial abscesses.

Osteogenic response and osteoprotective effects in vivo of a nanostructured titanium surface with antibacterial properties

In implantology, as an alternative approach to the use of antibiotics, direct surface modifications of the implant addressed to inhibit bacterial adhesion and to limit bacterial proliferation are a promising tactic. The present study evaluates in an in vivo normal model the osteogenic response and the osteointegration of an anodic spark deposition nanostructured titanium surface doped with gallium (ASD + Ga) in comparison with two other surface treatments of titanium: an anodic spark deposition treatment without gallium (ASD) and an acid etching treatment (CTR). Moreover the study assesses the osteoprotective potential and the antibacterial effect of the previously mentioned surface treatments in an experimentally-induced peri-implantitis model. The obtained data points out a more rapid primary fixation in ASD and ASD + Ga implants, compared with CTR surface. Regarding the antibacterial properties, the ASD + Ga surface shows osteoprotective action on bone peri-implant tissue in vivo as well as an antibacterial effect within the first considered time point.

Biomaterials approaches to treating implant-associated osteomyelitis

Orthopaedic devices are the most common surgical devices associated with implant-related infections and Staphylococcus aureus (S. aureus) is the most common causative pathogen in chronic bone infections (osteomyelitis). Treatment of these chronic bone infections often involves combinations of antibiotics given systemically and locally to the affected site via a biomaterial spacer. The gold standard biomaterial for local antibiotic delivery against osteomyelitis, poly(methyl methacrylate) (PMMA) bone cement, bears many limitations. Such shortcomings include limited antibiotic release, incompatibility with many antimicrobial agents, and the need for follow-up surgeries to remove the non-biodegradable cement before surgical reconstruction of the lost bone. Therefore, extensive research pursuits are targeting alternative, biodegradable materials to replace PMMA in osteomyelitis applications. Herein, we provide an overview of the primary clinical treatment strategies and emerging biodegradable materials that may be employed for management of implant-related osteomyelitis. We performed a systematic review of experimental biomaterials systems that have been evaluated for treating established S. aureus osteomyelitis in an animal model. Many experimental biomaterials were not decisively more efficacious for infection management than PMMA when delivering the same antibiotic. However, alternative biomaterials have reduced the number of follow-up surgeries, enhanced the antimicrobial efficacy by delivering agents that are incompatible with PMMA, and regenerated bone in an infected defect. Understanding the advantages, limitations, and potential for clinical translation of each biomaterial, along with the conditions under which it was evaluated (e.g. animal model), is critical for surgeons and researchers to navigate the plethora of options for local antibiotic delivery.

Elution of Clindamycin and Enrofloxacin From Calcium Sulfate Hemihydrate Beads In Vitro

OBJECTIVE

To compare the in vitro elution characteristics of clindamycin and enrofloxacin from calcium sulfate hemihydrate beads containing a single antibiotic, both antibiotics, and each antibiotic incubated in the same eluent well.

STUDY DESIGN

Experimental in vitro study.

METHODS

Calcium sulfate hemihydrate beads were formed by mixing with clindamycin and/or enrofloxacin to create 4 study groups: (1) 160 mg clindamycin/10 beads; (2) 160 mg enrofloxacin/10 beads; (3) 160 mg clindamycin + 160 mg enrofloxacin/10 beads; and (4) 160 mg clindamycin/5 beads and 160 mg enrofloxacin/5 beads. Chains of beads were formed in triplicate and placed in 5 mL phosphate buffered saline (PBS; pH 7.4 and room temperature) with constant agitation. Antibiotic-conditioned PBS was sampled at 14 time points from 1 hour to 30 days. Clindamycin and enrofloxacin concentrations in PBS were determined using high-performance liquid chromatography.

RESULTS

Eluent concentrations from clindamycin-impregnated beads failed to remain sufficiently above minimum inhibitory concentration (MIC) for common infecting bacteria over the study period. Enrofloxacin eluent concentrations remained sufficiently above MIC for common wound pathogens of dogs and cats and demonstrated an atypical biphasic release pattern. No significant differences in elution occurred as a result of copolymerization of the antibiotics into a single bead or from individual beads co-eluting in the same eluent well.

CONCLUSION

Clindamycin-impregnated beads cannot be recommended for treatment of infection at the studied doses; however, use of enrofloxacin-impregnated beads may be justified when susceptible bacteria are cultured.

Daptomycin-loaded polymethylmethacrylate bone cement for joint arthroplasty surgery

Antibiotic-loaded acrylic bone cement has been frequently used as an infection prophylaxis or antibiotic-loaded spacer in infected arthroplasty. In addition, daptomycin has been used recently against broad spectrum Gram-positive organisms. The goal of this in vitro study is to investigate the bacteriacidal and mechanical properties of daptomycin-incorporated polymethylmethacrylate (PMMA) bone cement and evaluate its feasibility for clinical use. Daptomycin (0.5, 1, or 2 g) was premixed with 40 g of PMMA bone cement powder before curing. The mechanical properties of the daptomycin-loaded acrylic bone cement (DLABC) were estimated following standard guidance, and the release profile and kinetics of daptomycin from PMMA were analyzed. The antimicrobial efficacy of DLABC was determined with a zone of inhibition (ZOI) assay against Staphylococcus aureus, Staphylococcus epidermis, Enterococcus faecalis, and Enterococcus faecium, respectively. The results showed that the compressive strength, of PMMA bone cement, which was higher than 100 MPa in all groups, was sufficient according to ISO 5833 after incorporation of daptomycin. The encapsulated daptomycin was released for 2 weeks with a 9.59 ± 0.85%, 15.25 ± 0.69%, and 20.64 ± 20.33% released percentage on the first day in the low, mid, and high groups, respectively. According to the calculated release kinetics, incorporated daptomycin should be 3.3 times the original dose to double its release. Although all recipes of DLABC had a microbial inhibitory effect, the effect with a higher encapsulated amount of daptomycin was more significant. Therefore, we believe that daptomycin can be locally delivered from PMMA bone cement at the surgical site as a prophylactic or treatment for osteomyelitis against Gram-positive organisms with intact cement function.

Relevance of microstructure for the early antibiotic release of fresh and pre-set calcium phosphate cements

Calcium phosphate cements (CPCs) have great potential as carriers for controlled release and vectoring of drugs in the skeletal system. However, a lot of work still has to be done in order to obtain reproducible and predictable release kinetics. A particular aspect that adds complexity to these materials is that they cannot be considered as stable matrices, since their microstructure evolves during the setting reaction. The aims of the present work were to analyze the effect of the microstructural evolution of the CPC during the setting reaction on the release kinetics of the antibiotic doxycycline hyclate and to assess the effect of the antibiotic on the microstructural development of the CPC. The incorporation of the drug in the CPC modified the textural and microstructural properties of the cements by acting as a nucleating agent for the heterogeneous precipitation of hydroxyapatite crystals, but did not affect its antibacterial activity. In vitro release experiments were carried out on readily prepared cements (fresh CPCs), and compared to those of pre-set CPCs. No burst release was found in any formulation. A marked difference in release kinetics was found at the initial stages; the evolving microstructure of fresh CPCs led to a two-step release. Initially, when the carrier was merely a suspension of α-TCP particles in water, a faster release was recorded, which rapidly evolved to a zero-order release. In contrast, pre-set CPCs released doxycycline following non-Fickian diffusion. The final release percentage was related to the total porosity and entrance pore size of each biomaterial.

RNA therapeutics targeting osteoclast-mediated excessive bone resorption

RNA interference (RNAi) is a sequence-specific post-transcriptional gene silencing technique developed with dramatically increasing utility for both scientific and therapeutic purposes. Short interfering RNA (siRNA) is currently exploited to regulate protein expression relevant to many therapeutic applications, and commonly used as a tool for elucidating disease-associated genes. Osteoporosis and their associated osteoporotic fragility fractures in both men and women are rapidly becoming a global healthcare crisis as average life expectancy increases worldwide. New therapeutics are needed for this increasing patient population. This review describes the diversity of molecular targets suitable for RNAi-based gene knock down in osteoclasts to control osteoclast-mediated excessive bone resorption. We identify strategies for developing targeted siRNA delivery and efficient gene silencing, and describe opportunities and challenges of introducing siRNA as a therapeutic approach to hard and connective tissue disorders.

Calcium phosphate cements as drug delivery materials

Calcium phosphate cements are used as synthetic bone grafts, with several advantages, such as their osteoconductivity and injectability. Moreover, their low-temperature setting reaction and intrinsic porosity allow for the incorporation of drugs and active principles in the material. It is the aim of the present work to: a) provide an overview of the different approaches taken in the application of calcium phosphate cements for drug delivery in the skeletal system, and b) identify the most significant achievements. The drugs or active principles associated to calcium phosphate cements are classified in three groups, i) low molecular weight drugs; ii) high molecular weight biomolecules; and iii) ions.

In vitro release kinetics and physical, chemical and mechanical characterization of a POVIAC®/CaCO3/HAP-200 composite

Coralline calcium-hydroxyapatite and calcium carbonate from Porites Porites coral were added to a polymeric matrix based on polyvinyl acetate (POVIAC(®)), to obtain a novel bone substitute composite as well as a system for the controlled drug (cephalexin) release. Composite samples with different compositions were characterized by physical-chemical and mechanical methods. Furthermore, the in vitro release profile of cephalexin and the kinetic behavior of its release from these composites were analyzed by appropriate mathematical models. It was shown that there is no chemical interaction between the inorganic filler and the polymer matrix, each conserving the original properties of the raw materials. The compressive mechanical strength and Young modulus of the composite with 17.5% of POVIAC(®), has better mechanical properties than those of cancellous bone. The variation of POVIAC(®) content can affect the cephalexin release kinetic in the composite. The cephalexin release mechanism from the composites can be considered as the result of the joint contribution of a prevailing Fickian diffusion and of polymer chain relaxation. It was also demonstrated that cephalexin is occluded inside the composites and not on their surface.

Total ear canal ablation and lateral bulla osteotomy for treatment of otitis externa and media in a rabbit

CASE DESCRIPTION

A 7-year-old spayed female Miniature Rex European rabbit (Oryctolagus cuniculus) was evaluated because of scratching at the right ear. Physical examination revealed purulent exudate in the right ear canal.

CLINICAL FINDINGS

Microbial culture of the exudate yielded Pseudomonas aeruginosa susceptible to marbofloxacin; however, the infection was refractory to appropriate medical treatment. Computed tomography revealed isoattenuating material within the right tympanic bulla and external ear canal with no enhancement following IV administration of contrast medium. The left tympanic bulla appeared normal.

TREATMENT AND OUTCOME

A total ear canal ablation and lateral bulla osteotomy were performed on the right ear, and polymethylmethacrylate beads containing either gentamicin or cefazolin were placed within the bulla and surrounding tissues. Two weeks after surgery, the patient appeared comfortable with no signs of scratching at the right ear.

CLINICAL RELEVANCE

Total ear canal ablation and lateral bulla osteotomy can be successfully performed for treatment of chronic otitis externa and media in rabbits. Cartilage plates that compose the external ear canal, a bony acoustic duct, lack of a horizontal ear canal, and thickness of the lateral aspect of the tympanic bulla are features unique to rabbits and have not been described in relation to these surgical procedures in rabbits. Rabbits also produce a caseous exudate, and it is difficult to resolve infections of bone and soft tissues. Placement of antimicrobial-impregnated polymethylmethacrylate beads is recommended to minimize the risk of recurrent infection.

Successful treatment of a prosthetic joint infection due to Mycobacterium abscessus

Prosthetic joint infection due to Mycobacterium abscessus is uncommon and optimal therapy remains poorly defined. Following a two-stage revision, clinical and microbiological cure was achieved in a patient with a M abscessus-infected total hip arthroplasty. A prolonged course of directed antibacterial therapy comprising clarithromycin and cefoxitin coupled with the application of amikacin-impregnated cement likely contributed to the successful outcome.

In vitro elution of amikacin and ticarcillin from a resorbable, self-setting, fiber reinforced calcium phosphate cement

OBJECTIVE

To determine in vitro elution characteristics of amikacin and ticarcillin from fiber reinforced calcium phosphate beads (FRCP).

SAMPLE POPULATION

Experimental.

METHODS

FRCP beads with water (A), amikacin (B), ticarcillin/clavulanate (C), or both amikacin and ticarcillin/clavulanate (D) were bathed in mL phosphate-buffered saline (PBS) at 37°C, 5% CO(2) and 95% room air. PBS was sampled (eluent) and beads were placed in fresh PBS at time points 1 and 8 hours and 1, 2, 3, 4, 5, 6, 7, 10, 12, 14, 18, 21, 25, 28, 35, 42, 49, and 56 days. Antibiotic concentration and antimicrobial activity of eluent against Escherichia coli, Staphylococcus aureus, and Klebsiella pneumoniae were determined.

RESULTS

Both antibiotics eluted in a bimodal pattern. Beads with a single antibiotic eluted 20.8 ± 2.5% of amikacin and 29.5 ± 0.8% of ticarcillin over 56 days. Coelution of the antibiotics resulted in a lower proportion (AUC(0-∞) ) of antibiotics eluted for both amikacin (9.5 ± 0.2%) and ticarcillin (21.7 ± 0.09%). Bioassay of antimicrobial activity of the eluent (t = 1, 8, and 24 hours) established reduced antimicrobial activity of amikacin from combination beads (D).

CONCLUSIONS

FRCP beads with amikacin or ticarcillin/clavulanate, but not the combination, are suitable carriers for wound implantation.

CLINICAL RELEVANCE

Duration before complete resorption of FRCP beads in vivo should be determined before clinical use as a resorbable depot. The results of this study underscore the importance of testing drug combinations, despite success of the combination systemically, before their use in local applications.

In vitro elution of amikacin and vancomycin from impregnated plaster of Paris beads

OBJECTIVE

To describe in vitro elution characteristics of amikacin and vancomycin from calcium sulfate hemihydrate 98% (plaster of Paris, POP) beads and characterize eluent inhibition of Staphylococcus spp.

STUDY DESIGN

Experimental study.

METHODS

POP beads were impregnated with amikacin or vancomycin alone or in combination and then incubated alone or in combination for 84 days at 37 degrees C in plastic tubes containing sterile phosphate-buffered saline (PBS). Beads containing no antimicrobial served as negative control. Beads were intermittently moved to a new tube containing drug-free PBS. Antimicrobial was measured in the eluent using a polarized fluorescent immunoassay. Eluent inhibition of Staphylococcus spp. was determined at each time point.

RESULTS

Antimicrobial release from beads was characterized by an initial rapid phase then a slower phase. Although antimicrobial release from beads occurred throughout the 84 days, most was in the first 24 hours, except for vancomycin alone. Duration of eluent inhibition of Staphylococcus spp. growth ranged from 0.5 (amikacin alone) to 56 days (vancomycin alone). Control eluent did not inhibit bacterial growth.

CONCLUSIONS

Amikacin elution from POP beads was rapid, inhibiting growth for <24 hours with or without vancomycin. Vancomycin elution was slower and inhibited growth for 56 days alone or for 5 days with amikacin.

CLINICAL RELEVANCE

Vancomycin-impregnated beads appear to be reasonable as a therapeutic option whereas amikacin-impregnated POP beads and amikacin and vancomycin combinations may require further study before considering as a therapeutic option.

Surgical management of complete diaphyseal third metacarpal and metatarsal bone fractures: clinical outcome in 10 mature horses and 11 foals

REASONS FOR PERFORMING STUDY

Osteosynthesis of third metacarpal (McIII) and third metatarsal (MtIII) bone fractures in horses is a surgical challenge and complications surrounding the repair are common. Retrospective studies evaluating surgical repair, complications and outcome are necessary to increase knowledge and improve success of long bone fracture repair in the horse.

OBJECTIVES

To evaluate clinical findings, surgical repair, post operative complications and outcome of 10 mature horses and 11 foals with McIII or MtIII fractures that were treated with open reduction and internal fixation (ORIF).

METHODS

Medical records were reviewed and follow-up information obtained by means of radiographs and/or telephone questionnaire.

RESULTS

Survival was achieved in 62% of the horses (3 mature/10 foals). On long-term evaluation (> 6 months) 11 horses (2 mature/9 foals) were fit for their intended activity, one mature horse had a chronic low grade lameness, and one foal was lost to follow-up because it was sold. The main fracture types were simple transverse (333%) or simple oblique (28.6%) and 71.4% of the fractures were open, 3 Type I (one mature/2 foals) and 12 type II (7 mature/5 foals). The preoperative assessment revealed inadequate emergency treatment in 10 horses (5 mature/5 foals; 47.6%). Survival rate of horses with open fractures was 12.5% (1/8) in mature and 85.7% (6/7) in foals. Post operative incisional infection (4 mature, 3 foals) was only managed successfully in 2 foals. Fracture instability related to inadequate fracture fixation technique occurred in 4 horses (all mature) and was always associated with unsuccessful outcome.

CONCLUSIONS

Age, bodyweight and infection are strongly associated with outcome in treatment of complete McIII/MtIII fractures.

CLINICAL RELEVANCE

Rigid fixation using plates and screws can be successful in treatment of closed or open, complete diaphyseal McIII/MtIII fractures in mature horses and foals. Instable fixation, infection and a bodyweight > 320 kg are major risk factors for unsuccessful outcome.

Cephalexin-loaded injectable macroporous calcium phosphate bone cement

Different types of calcium phosphate cements (CPCs) have been studied as potential matrices for incorporating different types of antibiotics. All of these matrices were morphologically microporous whereas macroporosity is essential for rapid cement resorption and bone replacement. In this study, liberation of cephalexin monohydrate (CMH) from a macroporous CPC was investigated over 0.5-300 h in simulated body fluid and some mathematical models were fitted to the release profiles. Macroporosity was introduced into the cement matrix by using sodium dodecyl sulfate molecules as air-entraining agents and the effect of both surfactant and CMH on basic properties of the CPC was studied. Incorporation of CMH into the CPC composition increased the setting time, decreased the crystallinity of the formed apatite phase, and improved the injectability of the paste. The use of both CMH and sodium dodecyl sulfate did not affect the rate of conversion of the reactants into apatite phase while soaking the cements in simulated body fluid. Results showed that the liberation rate of the drug from porous CPC was higher than that of the nonporous CPC but same release patterns were experienced in both types of cements, that is, like to nonporous CPC, a time-dependent controlled release of the incorporated drug was obtained from macroporous CPC. The Weibull model was the best fitting-equation for release profiles of all cements. The liberated CMH was as active as fresh cephalexin. It is concluded that this macroporous CPC can be successfully used as drug carrier with controlled release profile for the treatment of bone infections.

New antimicrobials, systemic distribution, and local methods of antimicrobial delivery in horses

The local delivery of antimicrobials is a valuable therapeutic tool with a low morbidity, is practical to use, and is well tolerated by horses. Clinically, its use has allowed equine practitioners to achieve better results when treating musculoskeletal infections, and it represents an extremely useful tool in the practitioner's armamentarium against these types of infections. The technique is indicated to combat orthopedic infections involving bones, joints, physes, tendon sheaths, and foot tissues. Optimal treatment must include other approaches, such as systemic antimicrobial therapy and surgical debridement and lavage, and monitoring of the clinical progression of the patient can help to determine the ideal protocol for each patient.

In vitro elution studies of amikacin and cefazolin from polymethylmethacrylate

OBJECTIVE

To compare the in vitro elution characteristics of amikacin and cefazolin from polymethylmethacrylate (PMMA) alone and in combination.

STUDY DESIGN

A prospective, controlled, experimental study.

METHODS

Three aliquots of 6 g sterile PMMA were measured and to them added (1) 750 mg amikacin; (2) 1050 mg cefazolin; and (3) 750 mg amikacin and 1050 mg cefazolin. Ten beads of each antimicrobial/PMMA combination were placed in 5 mL phosphate-buffered saline (PBS) at pH 7.4 and room temperature with constant agitation. PBS was sampled at 15 time points between 1 hour and 30 days. Amikacin concentrations were determined by fluorescence polarization immunoassay and cefazolin concentrations by high-performance liquid chromatography.

RESULTS

Amikacin and cefazolin eluted at concentrations greater than 8 and 4 times, respectively, above the minimum inhibitory concentration (MIC) for susceptible bacteria over 30 days. Co-elution of the antibiotics resulted in a greater rate and proportion of antibiotic eluted. Concentrations of amikacin and cefazolin in the co-eluted fluid were not maintained sufficiently above the MIC for selected bacteria over 30 days.

CONCLUSIONS

PMMA beads of only amikacin or cefazolin-eluted concentrations greater than the MIC for selected bacteria for 30 days. Co-elution of the antibiotics at the selected doses resulted in a significantly shorter duration of elution and may not be effective for treatment of wound infection.

CLINICAL RELEVANCE

Co-elution of amikacin and cefazolin from PMMA at the selected doses cannot be recommended for sustained treatment of infection.

Effects of porcine small intestinal submucosa on elution characteristics of gentamicin-impregnated plaster of Paris

OBJECTIVE

To evaluate effects of small intestinal submucosa (SIS) on elution properties of plaster of Paris (POP).

SAMPLE POPULATION

27 POP cylinders, 27 POP spheres, and 9 polymethylmethacrylate (PMMA) spheres.

PROCEDURES

Pellets were loaded with gentamicin (50 mg/g) and divided into 7 groups of 9 beads each: PMMA spheres; POP cylinders coated with 0, 4, or 8 layers of SIS; and POP spheres coated with 0, 4, or 8 layers of SIS. Gentamicin concentration was measured 6, 12, 18, 24, 32, 40, and 48 hours and 3, 4, 5, 7, 14, 21, 28, 35, and 42 days after wrapping. Porosity was evaluated via scanning electron microscopy. Curvature factor of elution curves, total amount of drug released (TDR), time required to reach 50% of total release (TDR(t50)), and number of days with concentrations > or = 1 microg/mL were compared among groups.

RESULTS

SIS decreased the curvature factor and increased the TDR(t50) and TDR of POP spheres and cylinders. Curvature factor of the PMMA-release curve remained lower than that for any POP group, but all POP groups wrapped in SIS released more gentamicin than PMMA spheres. Gentamicin concentrations remained > or = 1 microg/mL in SIS-wrapped POP and PMMA groups throughout the study. Wrapping POP in SIS minimized the increase in porosity of pellets.

CONCLUSIONS AND CLINICAL RELEVANCE

Wrapping POP with SIS slows the release and increases the amount of gentamicin leaching from spheres and cylinders. All groups wrapped in SIS maintained antimicrobial concentrations greater than the minimum inhibitory concentration of most pathogens.

Infection of a total hip prosthesis in a dog caused by Achromobacter(Alcaligenes) xylosoxidans

A four-year-old male, neutered Labrador retriever was presented with progressive left hindlimb lameness 10 months following total hip replacement. Radiography revealed changes consistent with infection and culture of joint fluid from the left coxofemoral joint revealed Achromobacter (Alcaligenes) xylosoxidans. The prosthesis was removed. Culture of the acetabular cup confirmed Achromobacter xylosoxidans. Achromobacter xylosoxidans is an uncommon but serious cause of nosocomial epidemics in hospitals for human beings. To the authors' knowledge, this is the first report of total hip prosthetic infection with Achromobacter xylosoxidans. Little is reported about its pathogenicity in human beings and the authors failed to retrieve any reports of its clinical significance in animals.

Osteomyelitis in Horses

Much has been learned in the past decade about osteomyelitis. The inhibitory mechanisms of the "biofilm slime" layer that is formed by bacterial extracapsular exopolysaccharides and binds to bone, joints, and implants are now better understood than in the past. The surface colonization of bacteria that occurs within these biofilms is a biologic phenomenon that is somewhat unique to orthopedic infections. This survival strategy of bacteria is effective, and it is important for veterinarians who treat osteomyelitis to be aware of current diagnostic and therapeutic treatment modalities. The practitioner should be aware of the most common bacteria associated with osteomyelitis and the traditional treatments that are still used. Current therapeutic treatment modalities, such as antibiotic- impregnated polymethylmethacrylate, antibiotic-impregnated plaster of Paris, and regional perfusion, have become routine, however, and have been responsible for improving the prevention and outcome of osteomyelitis in the horse. It is the intent of this article to make equine veterinarians aware of current information as well as the future treatments of osteomyelitis.

Calcium phosphate cements as bone drug delivery systems: A review

Since calcium phosphate cements were proposed, several formulations have been developed, some of them commercialised, and they have proven to be very efficient bone substitutes in different applications. Some of their properties, such as the injectability, or the low-temperature setting, which allows the incorporation of different drugs, make them very attractive candidates as drug carriers. In this article, the performance of calcium phosphate cements as carriers of different types of drugs, such as antibiotics, analgesics, anticancer, anti-inflammatory, as well as growth factors is reviewed.

[In vitro elution and mechanical properties of antibiotic-loaded SmartSet HV and Palacos R acrylic bone cements]

BACKGROUND

The continuing emergence of new bone cements with additional antibiotics makes it important to establish which one will provide the most favourable antibiotic elution. An in vitro antibiotic elution and mechanical study was therefore carried out to compare a newer bone cement, SmartSet, with the established Palacos R cement.

METHODS

Samples were prepared with each cement adding 1 g gentamicin, 1 g of vancomycin, or 1 g of gentamicin and vancomycin. The samples were analysed using fluorescence polarisation immunoassay. Mechanical tests were performed to determine whether any significant degradation in the cement strength occurred following addition of the antibiotic.

RESULTS

With regards to gentamicin release Palacos R eluted significantly more antibiotic over the study period than SmartSet (p<0.001). Both cements eluted significantly more gentamicin when two antibiotics were added. With respect to vancomycin release there was no significant difference. Palacos R was significantly stronger than SmartSet in the 4-point bending test when the gentamicin + vancomycin antibiotic groups were compared (p=0.01). Palacos R also demonstrated a higher elastic modulus than SmartSet when the gentamicin and gentamicin + vancomycin groups were compared (p=0.03, p=0.005).

CONCLUSIONS

Gentamcin shows better release characteristics from Palacos R. Both cements exhibited synergistic release of combined antibiotics.

Diagnosis and Treatment of Septic Arthritis

Septic arthritis (SA) is a common orthopedic condition encountered in horses that are presented to equine veterinarians. Successful out-come is dependent on prompt and thorough evaluation and treatment. This article briefly reviews the pathophysiology, outlines diagnostics, describes treatment options and prognostics, and discusses current research in diagnosis and treatment of SA.

Vertebroplasty and kyphoplasty: filler materials

Over 700,000 osteoporotic compression fractures occur each year in the United States, twice the number of hip fractures. These vertebral fractures, most of which occur in the elderly, represent significant personal and societal burdens. Percutaneous vertebroplasty (PVP) is a minimally invasive method that involves the percutaneous injection of polymethylmethacrylate (PMMA) into a collapsed vertebral body to stabilize the vertebra. Kyphoplasty is an advanced minimally invasive technique with a number of potential advantages over PVP, including lower risk of cement extravasation and better restoration of vertebral body height and spinal biomechanics. The filling materials used for both these techniques require good biocompatibility, good biomechanical strength and stiffness, and good radiopacity for the fluoroscopy guided procedures. New filler materials (synthetic bone substitutes, e.g., composite resin materials, calcium phosphate or calcium sulfate cements) in addition to new PMMA formulations are now available for clinical use. In this review paper, we will focus on the issues and characteristics of these filler materials as they pertain to vertebral augmentation procedures.