Quantum-state-resolved reactivity of overtone excited CH4on Ni(111): Comparing experiment and theory

Mid-Infrared Scattering in γ-Al2O3 Catalytic Powders

The energy efficiency of heterogeneous catalytic processes may be improved by using mid-infrared light to excite gas-phase reactants during the reaction, since vibrational excitation of molecules has been shown to increase their reactivity at the gas-catalyst interface. A primary challenge for such light-enabled catalysis is the need to ensure close coupling between light-excited molecules and the catalyst throughout the reactor. Thus, it is imperative to understand how to couple infrared light efficiently to molecules near and inside catalytic material. Heterogenous catalysts are often nanoscale metal particles supported on high surface area, porous oxide materials and exhibit feature sizes across multiple scattering regimes with respect to the mid-infrared wavelength. These complex powders make a direct measurement of the scattering properties challenging. Here, we demonstrate that a combination of directional hemispherical measurements along with the in-line transmission measurement allow for a direct measurement of the scattered light signal. We implement this technique to study the scattering behavior of the catalytic support material γ-Al₂O₃ (with and without metal loading) between 1040 and 1220 cm^-1. We first study how both the mean grain size affects the scattering behavior by comparing three different mean grain sizes spanning three orders of magnitude (2, 40, and 900 µm). Furthermore, we study how the addition of metal catalyst nanoparticles, Ru, or Cu, to the support material impacts the light scattering behavior of the powder. We find that the 40 µm grain size scatters the most (up to 97% at 1220 cm^-1) and that the addition of metal nanoparticles narrows the scattering angle but does not decrease the scattering efficiency. The strong scattering of the 40 µm grains makes them the most ideal support material of those studied for the given spectrum because of their ability to distribute light within the reactor. Finally, we estimate that less than 100 mW of laser power is needed to cause significant excitation for testing mid-infrared catalysis in a Harrick Praying Mantis diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) reactor, a magnitude easily available using commercial mid-infrared lasers. Our work also provides a mid-infrared foundation for a wide range of studies of light-enabled catalysis and can be extended to other wavelengths of light or to study the scattering behavior of other complex powders in other fields, including ceramics, biomaterials, and geology.

Computational approaches to dissociative chemisorption on metals: towards chemical accuracy

We review the state-of-the-art in the theory of dissociative chemisorption (DC) of small gas phase molecules on metal surfaces, which is important to modeling heterogeneous catalysis for practical reasons, and for achieving an understanding of the wealth of experimental information that exists for this topic, for fundamental reasons. We first give a quick overview of the experimental state of the field. Turning to the theory, we address the challenge that barrier heights (E_b, which are not observables) for DC on metals cannot yet be calculated with chemical accuracy, although embedded correlated wave function theory and diffusion Monte-Carlo are moving in this direction. For benchmarking, at present chemically accurate E_b can only be derived from dynamics calculations based on a semi-empirically derived density functional (DF), by computing a sticking curve and demonstrating that it is shifted from the curve measured in a supersonic beam experiment by no more than 1 kcal mol^-1. The approach capable of delivering this accuracy is called the specific reaction parameter (SRP) approach to density functional theory (DFT). SRP-DFT relies on DFT and on dynamics calculations, which are most efficiently performed if a potential energy surface (PES) is available. We therefore present a brief review of the DFs that now exist, also considering their performance on databases for E_b for gas phase reactions and DC on metals, and for adsorption to metals. We also consider expressions for SRP-DFs and briefly discuss other electronic structure methods that have addressed the interaction of molecules with metal surfaces. An overview is presented of dynamical models, which make a distinction as to whether or not, and which dissipative channels are modeled, the dissipative channels being surface phonons and electronically non-adiabatic channels such as electron-hole pair excitation. We also discuss the dynamical methods that have been used, such as the quasi-classical trajectory method and quantum dynamical methods like the time-dependent wave packet method and the reaction path Hamiltonian method. Limits on the accuracy of these methods are discussed for DC of diatomic and polyatomic molecules on metal surfaces, paying particular attention to reduced dimensionality approximations that still have to be invoked in wave packet calculations on polyatomic molecules like CH₄. We also address the accuracy of fitting methods, such as recent machine learning methods (like neural network methods) and the corrugation reducing procedure. In discussing the calculation of observables we emphasize the importance of modeling the properties of the supersonic beams in simulating the sticking probability curves measured in the associated experiments. We show that chemically accurate barrier heights have now been extracted for DC in 11 molecule-metal surface systems, some of which form the most accurate core of the only existing database of E_b for DC reactions on metal surfaces (SBH10). The SRP-DFs (or candidate SRP-DFs) that have been derived show transferability in many cases, i.e., they have been shown also to yield chemically accurate E_b for chemically related systems. This can in principle be exploited in simulating rates of catalyzed reactions on nano-particles containing facets and edges, as SRP-DFs may be transferable among systems in which a molecule dissociates on low index and stepped surfaces of the same metal. In many instances SRP-DFs have allowed important conclusions regarding the mechanisms underlying observed experimental trends. An important recent observation is that SRP-DFT based on semi-local exchange DFs has so far only been successful for systems for which the difference of the metal work function and the molecule's electron affinity exceeds 7 eV. A main challenge to SRP-DFT is to extend its applicability to the other systems, which involve a range of important DC reactions of e.g. O₂, H₂O, NH₃, CO₂, and CH₃OH. Recent calculations employing a PES based on a screened hybrid exchange functional suggest that the road to success may be based on using exchange functionals of this category.

Fundamental mechanisms for molecular energy conversion and chemical reactions at surfaces

The dream of theoretical surface chemistry is to predict the outcome of reactions in order to find the ideal catalyst for a certain application. Having a working ab initio theory in hand would not only enable these predictions but also provide insights into the mechanisms of surface reactions. The development of theoretical models can be assisted by experimental studies providing benchmark data. Though for some reactions a quantitative agreement between experimental observations and theoretical calculations has been achieved, theoretical surface chemistry is in general still far away from gaining predictive power. Here we review recent experimental developments towards the understanding of surface reactions. It is demonstrated how quantum-state resolved scattering experiments on reactive and nonreactive systems can be used to test front-running theoretical approaches. Two challenges for describing dynamics at surfaces are addressed: nonadiabaticity in diatomic molecule surface scattering and the increasing system size when observing and describing the dynamics of polyatomic molecules at surfaces. Finally recent experimental studies on reactive systems are presented. It is shown how elementary steps in a complex surface reaction can be revealed experimentally.