Molecular chemisorption of N2 on IrO2(110)

Surface chlorination of IrO2(110) by HCl

The ability to controllably chlorinate metal-oxide surfaces can provide opportunities for designing selective oxidation catalysts. In the present study, we investigated the surface chlorination of IrO2(110) by HCl using temperature programmed reaction spectroscopy (TPRS), x-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) calculations. We find that exposing IrO2(110) to HCl, followed by heating to 650 K in ultrahigh vacuum, produces nearly equal quantities of on-top and bridging Cl atoms on the surface, Clt and Clbr, where the Clbr atoms replace O-atoms that are removed from the surface by H2O formation. After HCl adsorption at 85 K, only H2O desorbs at low Cl coverages during TPRS, but HCl begins to desorb in increasing yields as the Cl coverage is increased above about 0.5 monolayer (ML). The desorption of Cl2 was not observed under any conditions, in good agreement with the high barrier for this reaction predicted by DFT. A maximum Cl coverage of 1 ML, with nearly equal coverages of Clt and Clbr atoms, could be generated by reacting HCl with IrO2(110) in UHV. Our results suggest that a kinetic competition between recombinative HCl and H2O desorption under the conditions studied limits the saturation Cl coverage to a value less than the 2 ML maximum predicted by thermodynamics. XPS further shows that the partitioning of Cl between the Clt and Clbr states can be altered by subjecting partially chlorinated IrO2(110) to reductive or oxidative treatments, demonstrating that the Cl site population can change dynamically in response to the gas environment. Our results provide insights for understanding the chlorination of IrO2(110) by HCl and can enable future experimental studies to determine how Cl-modification alters the surface chemical reactivity of IrO2(110) and potentially enhances selectivity toward partial oxidation chemistry.

Tuning Surface Potential Polarization to Enhance N2 Affinity for Ammonia Electrosynthesis

Electrocatalytic N2 reduction reaction (NRR) to synthesize ammonia is a sustainable reaction that is expected to replace Haber Bosch process. Laminated Bi2WO6 has great potential as an NRR electrocatalyst, however, the effective activity requires that the inert substrate is fully activated. Here, for the first time, success is achieved in activating the Bi2WO6 basal planes with NRR activity through Ti doping. The introduction of Ti successfully tunes the surface potential distribution and enhances the N2 adsorption. The subsequently strong hybrid coupling of d(Ti)-p(N) orbitals fills the electronic state of N2 antibonding molecular orbital, which greatly weakens the bonding strength of N≡N bonds. Further, in situ synchrotron radiation-based Fourier transform infrared (SR-FTIR) spectrum and theoretical calculations show that surface potential polarization enhances the adsorption of HNN* by Bi-Ti dual-metal sites, which is beneficial for the subsequent activation hydrogenation process. The Ti-Bi2WO6 nanosheets achieve 11.44% Faradaic efficiency (-0.2 V vs. RHE), a NH3 yield rate of 23.14 µg mg-1 h-1 (15N calibration), and satisfactory stability in 0.1 M HCl environment. The mutual assistance of theory and experiment can help understand and develop of excellent two-dimensional (2D) materials for the NRR.

Kinetics and selectivity of methane oxidation on an IrO2(110) film

Undercoordinated, bridging O-atoms (O_br) are highly active as H-acceptors in alkane dehydrogenation on IrO₂(110) surfaces but transform to HO_brgroups that are inactive toward hydrocarbons. The low C-H activity and high stability of the HO_brgroups cause the kinetics and product selectivity during CH₄oxidation on IrO₂(110) to depend sensitively on the availability of O_bratoms prior to the onset of product desorption. From temperature programmed reaction spectroscopy (TPRS) and kinetic simulations, we identified two O_br-coverage regimes that distinguish the kinetics and product formation during CH₄oxidation on IrO₂(110). Under excess O_brconditions, when the initial O_brcoverage is greater than that needed to oxidize all the CH₄to CO₂and HO_brgroups, complete CH₄oxidation is dominant and produces CO₂in a single TPRS peak between 450 and 500 K. However, under O_br-limited conditions, nearly all the initial O_bratoms are deactivated by conversion to HO_bror abstracted after only a fraction of the initially adsorbed CH₄oxidizes to CO₂and CO below 500 K. Thereafter, some of the excess CH_xgroups abstract H and desorb as CH₄above ∼500 K while the remainder oxidize to CO₂and CO at a rate that is controlled by the rate at which O_bratoms are regenerated from HO_brduring the formation of CH₄and H₂O products. We also show that chemisorbed O-atoms ('on-top O') on IrO₂(110) enhance CO₂production below 500 K by efficiently abstracting H from O_bratoms and thereby increasing the coverage of O_bratoms available to completely oxidize CH_xgroups at low temperature. Our results provide new insights for understanding factors which govern the kinetics and selectivity during CH₄oxidation on IrO₂(110) surfaces.

Formation and stability of small polarons at the lithium-terminated Li4Ti5O12 (LTO) (111) surface

Zero strain insertion, high cycling stability, and a stable charge/discharge plateau are promising properties rendering Lithium Titanium Oxide (LTO) a possible candidate for an anode material in solid state Li ion batteries. However, the use of pristine LTO in batteries is rather limited due to its electronically insulating nature. In contrast, reduced LTO shows an electronic conductivity several orders of magnitude higher. Studying bulk reduced LTO, we could show recently that the formation of polaronic states can play a major role in explaining this improved conductivity. In this work, we extend our study toward the lithium-terminated LTO (111) surface. We investigate the formation of polarons by applying Hubbard-corrected density functional theory. Analyzing their relative stabilities reveals that positions with Li ions close by have the highest stability among the different localization patterns.

High-Resolution X-ray Photoelectron Spectroscopy of an IrO2(110) Film on Ir(100)

High-resolution X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) were used to characterize IrO₂(110) films on Ir(100) with stoichiometric as well as OH-rich terminations. Core-level Ir 4f and O 1s peaks were identified for the undercoordinated Ir and O atoms and bridging and on-top OH groups at the IrO₂(110) surfaces. Peak assignments were validated by comparison of the core-level shifts determined experimentally with those computed using DFT, quantitative analysis of the concentrations of surface species, and the measured variation of the Ir 4f peak intensities with photoelectron kinetic energy. We show that exposure of the IrO₂(110) surface to O₂ near room temperature produces a large quantity of on-top OH groups because of reaction of background H₂ with the surface. The peak assignments made in this study can serve as a foundation for future experiments designed to utilize XPS to uncover atomic-level details of the surface chemistry of IrO₂(110).