Nickel-titanium alloys: stress-related temperature transitional range

A novel removable appliance for canine retraction: a case report

This case report outlines the use of a modified Leighton's retractor as a method for canine retraction in a patient with severe hypodontia, a history of aggressive periodontitis with tooth loss and idiopathic root resorption affecting multiple teeth. Treatment involved an upper removable appliance in combination with a lower sectional fixed appliance with the aim of improving aesthetics and function for the patient, whilst balancing the need to minimise treatment duration and modify treatment mechanics to reduce the orthodontic risks.

Can we expect similar behavior among CuNiTi 35°C wires?

Objective:

This paper aims to verify the thermodynamic, mechanical and chemical properties of CuNiTi 35ºC commercial wires.

Methods:

Forty pre-contoured copper-nickel-titanium thermodynamic 0.017 x 0.025-in archwires with an Af temperature of 35°C were used. Eight wires from five different manufacturers (American Orthodontics® [G1], Eurodonto® [G2], Morelli® [G3], Ormco® [G4] and Orthometric® [G5]) underwent cross-sectional dimension measurements, tensile tests, SEM-EDS and differential scanning calorimetry (DSC) tests. Parametric tests (One-way ANOVA and Tukey post-test) were used, with a significance level of 5%, and Pearson’s correlation coefficient test was performed between the Af and chemical elements of the wires. All sample tests and statistical analyses were double-blinded.

Results:

All wires presented standard dimensions (0.017 x 0.025-in) and superelastic behavior, with mean plateau forces of: G1 = 36.49N; G2 = 27.34N; G3 = 19.24 N; G4 = 37.54 N; and G5 = 17.87N. The Af means were: G1 = 29.40°C, G2 = 29.13°C and G3 = 31.43°C, with p>0.05 relative to each other. G4 (32.77°C) and G5 (35.17°C) presented statistically significant differences between each other and among the other groups. All samples presented Ni, Ti, Cu and Al in different concentrations.

Conclusions:

The chemical concentration of the elements that compose the alloy significantly influenced the thermodynamic and mechanical properties.

Comparison and ranking of superelasticity of different austenite active nickel-titanium orthodontic archwires using mechanical tensile testing and correlating with its electrical resistivity

Introduction:

The application of light and continuous forces for optimum physiological response and the least damage to the tooth supporting structures should be the primary aim of an orthodontist. Nickel-titanium (NiTi) alloys with their desirable properties are one of the natural choices of the clinicians.

Aim:

This study was aimed to compare and rank them based on its tensile strength and electrical resistivity.

Materials and Methods:

The sample consisted of eight groups of 0.017 inch × 0.025 inch rectangular archwires from eight different manufacturers, and five samples from each group for tensile testing and nine samples for electrical resistivity tests were used. Data for stress at 10% strain and the initial slope were statistically analyzed with an analysis of variance and Scheffe tests with P < 0.05. The stress/strain plots of each product were ranked for superelastic behavior. The rankings of the wires tested were based primarily on the unloading curve's slope which is indicative of the magnitude of the deactivation force and secondarily on the length of the horizontal segment which is indicative of continuous forces during deactivation. For calculating the electric resistivity, the change in resistance after inducing strain in the wires was taken into account for the calculation of degree of martensite transformation and for ranking.

Results:

In tensile testing Ortho Organizers wires ranked first and GAC Lowland NiTi wires ranked last. For resistivity tests Ormco A wires were found superior and Morelli remained last.

Conclusion:

these rankings should be correlated clinically and need further studies.

Superelasticity and force plateau of nickel-titanium springs: an in vitro study

OBJECTIVE

This paper analyzed whether nickel-titanium closed coil springs (NTCCS) have a different superelastic (SE) behavior according to activation and whether their force plateau corresponds to that informed by the manufacturer.

METHODS

A total of 160 springs were divided into 16 subgroups according to their features and activated proportionally to the length of the extensible part (NiTi) of the spring (Y). The force values measured were analyzed to determine SE rates and force plateaus, which were mathematically calculated. These plateaus were compared to those informed by the manufacturer. Analysis of variance was accomplished followed by Tukey post-hoc test to detect and analyze differences between groups.

RESULTS

All subgroups were SE at the activation of 400% of Y length, except for: subgroups 4B and 3A, which were SE at 300%; subgroups 4E and 4G, which were SE at 500%; and subgroup 3C, which was SE at 600%. Subgroup 3B did not show a SE behavior. Force plateaus depended on activation and, in some subgroups and some activations, were similar to the force informed.

CONCLUSIONS

Most of the springs showed SE behavior at 400% of activation. Force plateaus are difficult to compare due to lack of information provided by manufacturers.

Comparison of deactivation forces between thermally activated nickel-titanium archwires

OBJECTIVE

The aim of the present study was to investigate and compare load-deflection characteristics of commercially available thermally activated nickel-titanium archwires using a three-point bending test.

MATERIALS AND METHODS

Sixty thermally activated 0.019×0.025-inch nickel-titanium archwires from six different manufacturers were investigated. The superelastic properties of these archwires were evaluated by conducting a three-point bending test under identical testing conditions. Forces generated at deactivation for a deflection of 0.5, 1, 2 and 3 mm at a temperature of 37° C were selected for statistical comparison of the data. The results of forces of deactivation at all deflections applied were compared by two-way analysis of variance and the Tukey test.

RESULTS

Statistical differences (P<0.05) were found at all force levels during deactivations. The results showed that the range of forces displayed great variation in quantitative behaviour. None of the archwires showed permanent deformation after the three-point bending test.

CONCLUSIONS

This study revealed significant differences in deactivation forces among the six types of thermally activated nickel-titanium archwires tested. NiTinol Termoativado (Aditek) and NeoSentalloy F200 (GAC) produced the least amount of force in all four deactivation categories.

Thermal and mechanical characteristics of stainless steel, titanium-molybdenum, and nickel-titanium archwires

INTRODUCTION

In recent years, nickel-titanium (Ni-Ti) archwires have been developed that undergo thermal transitions. Before the practitioner can fully utilize these products, the effect of those transitions within the clinical application must be understood.

METHODS

The transitional temperatures and mechanical stiffnesses of 3 archwire alloys--stainless steel, beta-titanium, and Ni-Ti--were investigated were for 7 products. Among the nickel-titanium alloys, 2 were thought to represent classic Ni-Ti products and 3 copper (Cu)-Ni-Ti products. By using 2 techniques, differential scanning calorimetry to measure heat flow and dynamic mechanical analysis to measure storage modulus, transition temperatures were evaluated from -30 degrees C to +80 degrees C.

RESULTS

With regard to the first technique, no transitions were observed for the stainless steel alloy, the beta-titanium alloy, and 1 of the 2 classic Ni-Ti products. For the other classic Ni-Ti product, however, a martensitic-austenitic transition was suggested on heating, and a reverse transformation was suggested on cooling. As expected, the Cu-Ni-Ti 27, 35, and 40 products manifested austenitic finish temperatures of 29.3 degrees C, 31.4 degrees C, and 37.3 degrees C, respectively, as the enthalpy increased from 2.47 to 3.18 calories per gram. With regard to the second technique, the storage modulus at a low frequency of 0.1 Hz paralleled static mechanical tests for the stainless steel alloy (183 gigapascal [GPa]), the beta-titanium alloy (64 GPa), and the Nitinol Classic (3M Unitek, Monrovia, Calif) product that represented a stable martensitic phase (41 GPa). The remaining 4 Ni-Ti products generally varied from 20 to 35 GPa when the low-temperature or martensitic phase was present and from 60 to 70 GPa after the high-temperature or austenitic phase had formed.

CONCLUSIONS

From the clinical viewpoint, the Orthonol (Rocky Mountain Orthodontics, Denver, Colo), Cu-Ni-Ti 27, Cu-Ni-Ti 35, and Cu-Ni-Ti 40 (SDS/Ormco, Glendora, Calif) products increased at least twofold in stiffness as temperature increased, best emulating the stiffness of Nitinol Classic below the transformational temperature and the stiffness of TMA (SDS/Ormco, Glendora, Calif) above the transformational temperature. Of the 3 Cu-Ni-Ti products, the least differences were found between Cu-Ni-Ti 27 and Cu-Ni-Ti 35, thereby questioning the justification for 3 similar products.

Accuracy of third-order bends of nickel-titanium wires and the effect of high and low pressure during memorizing heat treatment

This study evaluated the accuracy of third-order bends of nickel-titanium wires and determined the effect of high and low pressure for maintaining the wire shape during memorizing heat treatment. A computer-aided bending machine was used to incorporate 200 randomly determined torsional angles between 0 degrees and 60 degrees into 30 linear 0.016 x 0.022-in NeoSentalloy F80 (GAC International, Central Islip, NY) wires. The torsional bendings were randomized into 2 groups. Bends assigned to group 1 (n = 100) received heat treatment of 1.6 MPa (16 bar) pressure, and bends assigned to group 2 (n = 100) received heat treatment of 50 MPa (500 bar) pressure. Cross-sectional cuts from the bent wires were prepared by using standard metallurgical techniques, and the torsional angles were analyzed under computer control. The results of our study show that third-order bends </= 30 degrees can be made with adequate clinical accuracy with an error of 1.89 degrees +/- 1.75 degrees (0 degrees to 10 degrees ) and 3.57 degrees +/- 1.57 degrees (20 degrees to 30 degrees ), irrespective of the pressure applied. With bends > 30 degrees but </= 40 degrees , the method with the higher pressure offers fundamentally greater precision than that with the lower pressure. With torque bends > 40 degrees , the bending error with both methods is clinically unacceptable. In addition to the variability in the dimension and composition of nickel-titanium wires, the scale of the incorporated plastic deformations makes a substantial contribution to the bending error. As far as permitted by the clinical situation, then, the bend should be distributed over the maximum possible wire length. Third-order bends in the first rectangular pseudoelastic nickel-titanium wires represent an efficient means of effecting torque at an early stage. This individualization allows the full therapeutic potential of these archwires to be exploited right from the initial phase of treatment.

Force-deflection comparison of superelastic nickel-titanium archwires

This in vitro study compared the force-deflection behavior of 6 superelastic nickel-titanium orthodontic archwires (0.016 x 0.022 in) under controlled moment and temperature. To simulate leveling, maxillary canine brackets and first molar tubes were bonded in such a manner as to remove the tip and angulation from the system. The wires (n = 10) were passively self-ligated into stainless steel brackets attached to an acrylic jig to simulate the maxillary arch. A testing machine recorded deactivations of 3 distances (5, 4, and 3 mm) at 37 degrees C in the canine position. Force-deflection measurements were recorded from the deactivations only. Forces produced during deactivation, at deflections of 2.5, 2.0, and 1.5 mm, were compared by analysis of variance. Significant differences (P < 0.0001) in forces were observed among the wires at the various deflections. All wires exhibited superelastic behavior, and rankings were derived according to statistically significant differences for each deflection distance.

Pseudoelasticity and thermoelasticity of nickel-titanium alloys: a clinically oriented review. Part II: Deactivation forces

The purpose of this review was to organize a systematic reference to help orthodontists evaluate commonly used orthodontic nickel-titanium alloys. Part I of the article reviewed the data available in the literature regarding the temperature transitional ranges of the alloys. The thermomechanical behavior of these compounds is, in fact, strictly dependent upon the correlation between the temperature transitional range and the oral temperature range. Part II focuses on the mechanical characteristics of the alloys, such as the magnitude of the forces delivered and correlations with the temperature transitional range and oral temperature.

Pseudoelasticity and thermoelasticity of nickel-titanium alloys: a clinically oriented review. Part I: Temperature transitional ranges

The purpose of this review was to organize a systematic reference to help orthodontists evaluate commonly used orthodontic nickel-titanium alloys. Part I of the article reviews the data available in the literature regarding the temperature transitional ranges of the alloys. The thermomechanical behavior of these compounds is, in fact, strictly dependent on the correlation between the temperature transitional range and the oral temperature range. Part II of the article will focus on the mechanical characteristics of the alloys, such as the magnitude of the forces delivered and its correlations with temperature transitional range and oral temperature.