Fabrication of Core–Shell Novel Polyurea Microcapsules Using Isophorone Diisocyanate (IPDI) Trimer for Release System

Saponin Stabilization via Progressive Freeze Concentration and Sterilization Treatment

Saponin is a biopesticide used to suppress the growth of the golden apple snail population. This study aims to determine the stabilized conditions for saponin storage. The maceration process was used for saponin extraction, and for saponin concentration, progressive freeze concentration (PFC) was used. Afterwards, stability analysis was performed by storing the sample for 21 days in two conditions: Room temperature (26 °C) and cold room (10 °C). The samples kept in a cold room were sterilized samples that undergo thermal treatment by placing the sample in the water bath. The non-sterilized samples were kept in room temperature condition for 21 days. The results showed that saponin stored in the cold room (sterilized sample) has low degradation with higher concentration than those stored at room temperature in stability analysis with the highest saponin concentration (0.730 mg/mL) at a concentration temperature of −6 °C and concentration time of 15 min. The lowest saponin concentration obtained by saponin stored at room temperature (non-sterilized sample) is 0.025 mg/mL at a concentration temperature of −6 °C and concentration time of 10 min. Thus, the finding concluded that saponin is sensitive to temperature. Hence, the best storage condition to store saponin after thermal treatment is to keep it in a cold room at 10 °C.

Preparation of Poly(ethylene glycol)@Polyurea Microcapsules Using Oil/Oil Emulsions and Their Application as Microreactors

The development process of catalytic core/shell microreactors, possessing a poly(ethylene glycol) (PEG) core and a polyurea (PU) shell, by implementing an emulsion-templated non-aqueous encapsulation method, is presented. The microreactors' fabrication process begins with an emulsification process utilizing an oil-in-oil (o/o) emulsion of PEG-in-heptane, stabilized by a polymeric surfactant. Next, a reaction between a poly(ethylene imine) (PEI) and a toluene-2,4-diisocyanate (TDI) takes place at the boundary of the emulsion droplets, resulting in the creation of a PU shell through an interfacial polymerization (IFP) process. The microreactors were loaded with palladium nanoparticles (NPs) and were utilized for the hydrogenation of alkenes and alkynes. Importantly, it was found that PEG has a positive effect on the catalytic performance of the developed microreactors. Interestingly, besides being an efficient green reaction medium, PEG plays two crucial roles: first, it reduces the palladium ions to palladium NPs; thus, it avoids the unnecessary use of additional reducing agents. Second, it stabilizes the palladium NPs and prevents their aggregation, allowing the formation of highly reactive palladium NPs. Strikingly, in one sense, the suggested system affords highly reactive semi-homogeneous catalysis, whereas in another sense, it enables the facile, rapid, and inexpensive recovery of the catalytic microreactor by simple centrifugation. The durable microreactors exhibit excellent activity and were recycled nine times without any loss in their reactivity.

A Multi-Scale Approach to Microencapsulation by Interfacial Polymerization

This work applies a multi-scale approach to the microencapsulation by interfacial polymerization. Such microencapsulation is used to produce fertilizers, pesticides and drugs. In this study, variations at three different scales (molecular, microscopic and macroscopic) of product design (i.e., product variables, process variables and properties) are considered simultaneously. We quantify the effect of the formulation, composition and pH change on the microcapsules’ properties. Additionally, the method of measuring the strength of the microcapsules by crushing a sample of microcapsules’ suspension was tested. Results show that the xylene release rate in the microcapsules decreases when the amine functionality is greater due to a stronger crosslinking. Such degree of crosslinking increases the compression force over the microcapsules and improves their appearance. When high levels of amine concentration are used, the initial pH values in the reaction are also high which leads to agglomeration. This study provides a possible explanation to the aggregation based on the kinetic and thermodynamic controls in reactions and shows that the pH measurements account for the polyurea reaction and carbamate formation, which is a reason why this is not a suitable method to study kinetics of polymerization. Finally, the method used to measure the compressive strength of the microcapsules detected differences in formulations and composition with low sensibility.

Pretilachlor Releasable Polyurea Microcapsules Suspension Optimization and Its Paddy Field Weeding Investigation

In this study, pretilachlor was encapsulated into polyurea microcapsules prepared by water-initiated polymerization of polyaryl polymethylene isocyanate and eventually made into pretilachlor microcapsules suspension (PMS). We used response surface methodology (RSM) combined with the Box–Behnken design (BBD) model to optimize the formulation of PMS. The encapsulation efficiency (EE) of PMS was investigated with respect to three independent variables including wall material dosage (X₁), emulsifier dosage (X₂), and polymerization stirring speed (X₃). The results showed that the regression equation model had a satisfactory accuracy in predicting the EE of PMS. To achieve an optimal condition for PMS preparation, the dose of wall material was set to 5%, the dose of emulsifier was set to 3.5% and the polymerization stirring speed was set to 200 rpm. The EE of PMS was up to 95.68% under the optimized condition, and the spherical shape with smooth surface morphology was observed. PMS was also proven to have delayed release capability and in vivo herbicidal activity against barnyard grass [Echinochloa crusgalli (L.) Beauv.] with an LC₅₀ value of 274 mg/L. Furthermore, PMS had efficient weed management compared to commercially available 30% pretilachlor emulsifier (PE), showing a promising potential application for weeding paddy fields.