1
|
Gubitosa J, Rizzi V, Fini P, Nuzzo S, Cosma P. Kiwi peel waste as a recyclable adsorbent to remove textile dyes from water: Direct Blue 78 removal and recovery. Phys Chem Chem Phys 2024; 26:9891-9905. [PMID: 38465407 DOI: 10.1039/d4cp00174e] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 03/12/2024]
Abstract
According to circular bioeconomy principles, the use of kiwi peels to remove Direct Blue 78 (DB) from water is investigated during this work, proposing food waste as a recyclable adsorbent substrate. Direct Blue 78 (DB) was adopted as a model pollutant, employing its visible spectrum to monitor its adsorption. The adsorption process was thus fully characterized, investigating the roles of ionic strength, pH values, adsorbent/pollutant amounts, and temperature. The thermodynamics, kinetics, and adsorption isotherms were also studied. To extend the kiwi peels' lifetime, quite complete desorption was obtained by adopting hot water as a safe and eco-friendly strategy. Despite the relatively low kiwi peels' maximum adsorption capacity (6 mg g-1) for DB when adsorbed in the presence of NaCl, 10 cycles of adsorption/desorption were attempted, proposing the recycling of both the dye and kiwi peels as dictated by circular economy principles. Dyeing experiments were also performed, evidencing the dye's ability to color cotton fabrics after its recycling. Finally, the removal of other textile dyes, Direct Red 83 : 1 and Direct Yellow 86, was demonstrated in a mixture with DB. A preliminary investigation was performed to find the best working conditions for inducing the solid-state dye photodegradation, proposing a possible alternative for the adsorbent regeneration.
Collapse
Affiliation(s)
- Jennifer Gubitosa
- Dipartimento di Chimica, Università degli Studi di Bari "Aldo Moro", Via Orabona, 4-70126 Bari, Italy.
| | - Vito Rizzi
- Dipartimento di Chimica, Università degli Studi di Bari "Aldo Moro", Via Orabona, 4-70126 Bari, Italy.
| | - Paola Fini
- Consiglio Nazionale delle Ricerche CNR-IPCF, UOS Bari, Via Orabona, 4-70126 Bari, Italy
| | - Sergio Nuzzo
- Consiglio Nazionale delle Ricerche CNR-IPCF, UOS Bari, Via Orabona, 4-70126 Bari, Italy
| | - Pinalysa Cosma
- Dipartimento di Chimica, Università degli Studi di Bari "Aldo Moro", Via Orabona, 4-70126 Bari, Italy.
- Consiglio Nazionale delle Ricerche CNR-IPCF, UOS Bari, Via Orabona, 4-70126 Bari, Italy
| |
Collapse
|
2
|
Viotti P, Marzeddu S, Antonucci A, Décima MA, Lovascio P, Tatti F, Boni MR. Biochar as Alternative Material for Heavy Metal Adsorption from Groundwaters: Lab-Scale (Column) Experiment Review. MATERIALS (BASEL, SWITZERLAND) 2024; 17:809. [PMID: 38399060 PMCID: PMC10890072 DOI: 10.3390/ma17040809] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/22/2023] [Revised: 01/22/2024] [Accepted: 01/31/2024] [Indexed: 02/25/2024]
Abstract
The purpose of this manuscript is to present a review of laboratory experiments (including methodology and results) that use biochar, a specific carbon obtained by a pyrolysis process from different feedstocks, as an alternative material for heavy metal adsorption from groundwater. In recent years, many studies have been conducted regarding the application of innovative materials to water decontamination to develop a more sustainable approach to remediation processes. The use of biochar for groundwater remediation has particularly attracted the interest of researchers because it permits the reuse of materials that would be otherwise disposed of, in accordance with circular economy, and reduces the generation of greenhouse gases if compared to the use of virgin materials. A review of the different approaches and results reported in the current literature could be useful because when applying remediation technologies at the field scale, a preliminary phase in which the suitability of the adsorbent is evaluated at the lab scale is often necessary. This paper is therefore organised with a short description of the involved metals and of the biochar production and composition. A comprehensive analysis of the current knowledge related to the use of biochar in groundwater remediation at the laboratory scale to obtain the characteristic parameters of the process that are necessary for the upscaling of the technology at the field scale is also presented. An overview of the results achieved using different experimental conditions, such as the chemical properties and dosage of biochar as well as heavy metal concentrations with their different values of pH, is reported. At the end, numerical studies useful for the interpretation of the experiment results are introduced.
Collapse
Affiliation(s)
- Paolo Viotti
- Department of Civil, Building and Environmental Engineering (DICEA), Faculty of Civil and Industrial Engineering, Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
| | - Simone Marzeddu
- Department of Civil, Building and Environmental Engineering (DICEA), Faculty of Civil and Industrial Engineering, Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
| | - Angela Antonucci
- Department of Civil, Building and Environmental Engineering (DICEA), Faculty of Civil and Industrial Engineering, Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
| | - María Alejandra Décima
- Department of Civil, Building and Environmental Engineering (DICEA), Faculty of Civil and Industrial Engineering, Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
| | - Pietro Lovascio
- Department of Civil, Building and Environmental Engineering (DICEA), Faculty of Civil and Industrial Engineering, Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
| | - Fabio Tatti
- National Centre of Waste and Circular Economy, Italian Institute for Environmental Protection and Research (ISPRA), Via Vitaliano Brancati 48, 00144 Rome, Italy
| | - Maria Rosaria Boni
- Department of Civil, Building and Environmental Engineering (DICEA), Faculty of Civil and Industrial Engineering, Sapienza University of Rome, Via Eudossiana 18, 00184 Rome, Italy
| |
Collapse
|
3
|
Núñez-Delgado A, Dominguez JR, Zhou Y, Race M. New trends on green energy and environmental technologies, with special focus on biomass valorization, water and waste recycling: editorial of the special issue. JOURNAL OF ENVIRONMENTAL MANAGEMENT 2022; 316:115209. [PMID: 35533594 DOI: 10.1016/j.jenvman.2022.115209] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/22/2022] [Accepted: 04/30/2022] [Indexed: 06/14/2023]
Abstract
In this editorial piece, the Editors of the Virtual Special Issue (VSI) "New Trends on Green Energy and Environmental Technologies, with Special Focus on Biomass Valorization, Water and Waste Recycling", present summarized data corresponding to the accepted submissions, as well as additional comments regarding the thematic of the VSI. Overall, 83 manuscripts were received, with final publication of those having the highest quality, accepted after peer-reviewing. The Editors think that the result is a set of very interesting papers that increase the knowledge on the matter, and which would be useful for researchers and the whole society.
Collapse
Affiliation(s)
- Avelino Núñez-Delgado
- Dept. Soil Sci. and Agric. Chem., Univ. Santiago de Compostela, Engineering Polytech. School, Campus Univ. S/n, 27002, Lugo, Spain.
| | - Joaquín R Dominguez
- Department of Chemical Engineering and Physical Chemistry, University of Extremadura, Spain
| | - Yaoyu Zhou
- College of Resources and Environment, Hunan Agricultural University, Changsha, 410128, Hunan Province, China
| | - Marco Race
- Department of Civil and Mechanical Engineering, University of Cassino and Southern Lazio, Via di Biasio 43, 03043, Cassino, Italy
| |
Collapse
|
4
|
Regenerable Kiwi Peels as an Adsorbent to Remove and Reuse the Emerging Pollutant Propranolol from Water. Processes (Basel) 2022. [DOI: 10.3390/pr10071417] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/16/2022] Open
Abstract
This work aims to characterize the adsorption process of propranolol HCl, an emerging pollutant and a widely used β-blocker, onto kiwi peels, an agricultural waste. The use of UV-vis spectroscopy was considered to obtain information about the pollutant removal working in the in-batch mode. In a relatively short time, the adsorption process could remove the pollutant from water. A kiwi peel maximum adsorption capacity of 2 mg/g was obtained. With the perspective of scaling up the process, preliminary in-flux measurements were also performed. The investigation of the whole in-batch adsorption process was conducted by studying the effect of ionic strength (adopting salt concentrations from 0 to 0.4 M), pH values (from 2 to 12), adsorbent/pollutant amounts (from 25 to 100 mg and from 7.5 to 15 mg/L, respectively), and temperature values (from 289 to 305 K). The thermodynamics, the adsorption isotherms, and the kinetics of the adsorption process were also carefully investigated. The Langmuir model fitted the experimental data well, with an R2 of 0.9912, restituting KL: 1 L/mg and Q0: 1.8 mg/g. The temperature increase enhanced the pollutant removal due to the endothermic adsorption characteristics. Accordingly, a ΔH°298K of +70 KJ/mol was obtained. The pseudo-first-order kinetic model described the process. Due to the results observed during the study of the effects of pH and ionic strength, the prominent presence of electrostatic interactions, working in synergy with hydrophobic forces and H-bonds between the pollutant and kiwi peel surfaces, was successfully demonstrated. In particular, FTIR-ATR measurements confirmed the latter findings. Finally, desorption experiments for recycling 100% of propranolol for each cycle were performed using 0.1 M MgCl2. Ten cycles of adsorption/desorption were obtained and indicated that the percentage of propranolol removal was not affected during each run, increasing the maximum adsorption from 2 to 20 mg/g.
Collapse
|
5
|
Experimental Investigation on Environmentally Sustainable Cement Composites Based on Wheat Straw and Perlite. MATERIALS 2022; 15:ma15020453. [PMID: 35057171 PMCID: PMC8777943 DOI: 10.3390/ma15020453] [Citation(s) in RCA: 6] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 12/21/2021] [Revised: 12/30/2021] [Accepted: 01/05/2022] [Indexed: 12/04/2022]
Abstract
Environmentally sustainable cement mortars containing wheat straw (Southern Italy, Apulia region) of different length and dosage and perlite beads as aggregates were prepared and characterised by rheological, thermal, acoustic, mechanical, optical and microstructural tests. A complete replacement of the conventional sand was carried out. Composites with bare straw (S), perlite (P), and with a mixture of inorganic and organic aggregates (P/S), were characterised and compared with the properties of conventional sand mortar. It was observed that the straw fresh composites showed a decrease in workability with fibre length decrease and with increase in straw volume, while the conglomerates with bare perlite, and with the aggregate mixture, showed similar consistency to the control. The thermal insulation of the straw mortars was extremely high compared to the sand reference (85–90%), as was the acoustic absorption, especially in the 500–1000 Hz range. These results were attributed to the high porosity of these composites and showed enhancement of these properties with decrease in straw length and increase in straw volume. The bare perlite sample showed the lowest thermal insulation and acoustic absorption, being less porous than the former composites, while intermediate values were obtained with the P/S samples. The mechanical performance of the straw composites increased with length of the fibres and decreased with fibre dosage. The addition of expanded perlite to the mixture produced mortars with an improvement in mechanical strength and negligible modification of thermal properties. Straw mortars showed discrete cracks after failure, without separation of the two parts of the specimens, due to the aggregate tensile strength which influenced the impact compression tests. Preliminary observations of the stability of the mortars showed that, more than one year from preparation, the conglomerates did not show detectable signs of degradation.
Collapse
|
6
|
Methyl Orange Photo-Degradation by TiO2 in a Pilot Unit under Different Chemical, Physical, and Hydraulic Conditions. Processes (Basel) 2021. [DOI: 10.3390/pr9020205] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/04/2023] Open
Abstract
The photo-catalytic degradation of a textile azo-dye as Methyl Orange was studied in an innovative unit constituted by a channel over which a layer of titanium dioxide (TiO2) catalyst in anatase form was deposited and activated by UVB irradiation. The degradation kinetics were followed after variation of the chemical, physical, and hydraulic/hydrodynamic parameters of the system. For this purpose, the influence of the TiO2 dosage (g/cm3), dye concentration (mg/L), pH of the solution, flow-rate (L/s), hydraulic load (cm), and irradiation power (W) were evaluated on the degradation rates. It was observed that the maximum dosage of TiO2 was 0.79 g/cm3 while for higher dosage a reduction of homogeneity of the cement conglomerate occurred. The Langmuir–Hinshelwood (LH) kinetic model was followed up to a dye concentration around 1 mg/L. It was observed that with the increase of the flow rate, an increase of the degradation kinetics was obtained, while the further increase of the flow-rate associated with the modification of the hydraulic load determined a decrease of the kinetic rates. The results also evidenced an increase of the kinetic rates with the increase of the UVB intensity. A final comparison with other dyes such as Methyl Red and Methylene Blue was carried out in consideration of the pH of the solution, which sensibly affected the removal efficiencies.
Collapse
|
7
|
Rizzi V, Gubitosa J, Fini P, Romita R, Nuzzo S, Gabaldón JA, Gorbe MIF, Gómez-Morte T, Cosma P. Chitosan film as recyclable adsorbent membrane to remove/recover hazardous pharmaceutical pollutants from water: the case of the emerging pollutant Furosemide. JOURNAL OF ENVIRONMENTAL SCIENCE AND HEALTH. PART A, TOXIC/HAZARDOUS SUBSTANCES & ENVIRONMENTAL ENGINEERING 2020; 56:145-156. [PMID: 33284713 DOI: 10.1080/10934529.2020.1853985] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/29/2020] [Revised: 11/13/2020] [Accepted: 11/16/2020] [Indexed: 06/12/2023]
Abstract
Due to the negative effects of emerging contaminants on the environment, that can potentially induce deleterious effects in aquatic and human life, this paper focuses on the removal from the water of Furosemide, through the adsorption process. Indeed, only a few papers are available in the literature about the Furosemide adsorption and, chitosan films are thus proposed for this purpose as safe, sustainable, and recyclable adsorbent materials. In the present work, the effects on the adsorption process of several experimental parameters such as the pH values, ionic strength, amount of adsorbent/pollutant, and temperature values were investigated. The kinetics models, isotherms of adsorption, and the thermodynamic parameters were studied showing that the Furosemide physisorption occurred on the heterogeneous Chitosan surface, endothermically (ΔH° = +31.27 ± 3.40 kJ mol-1) and spontaneously (ΔS° = +150.00 ± 10.00 J mol-1 K-1), following a pseudo-second-order kinetic model. The 90% of the pollutant was adsorbed in 2 h, with a maximum adsorption capacity of 3.5 mg × g-1. Despite these relatively low adsorption capacities, experiments of desorption were performed and 100% of adsorbed Furosemide was recovered by using concentrated NaCl solutions, proposing a low-cost and green approach, with respect to the previous literature relative to the Furosemide adsorption, fundamental for the pollutant recovery and adsorbent reuse.
Collapse
Affiliation(s)
- Vito Rizzi
- Dip. Chimica, Università degli Studi "Aldo Moro" di Bari, Bari, Italy
| | - Jennifer Gubitosa
- Dip. Chimica, Università degli Studi "Aldo Moro" di Bari, Bari, Italy
| | - Paola Fini
- Consiglio Nazionale delle Ricerche CNR-IPCF, UOS Bari, Bari, Italy
| | - Roberto Romita
- Dip. Chimica, Università degli Studi "Aldo Moro" di Bari, Bari, Italy
| | - Sergio Nuzzo
- Consiglio Nazionale delle Ricerche CNR-IPCF, UOS Bari, Bari, Italy
| | - José Antonio Gabaldón
- Departamento Ciencia y Tecnología de Alimentos, Universidad Católica San Antonio de Murcia, Guadalupe, Murcia, Spain
| | - María Isabel Fortea Gorbe
- Departamento Ciencia y Tecnología de Alimentos, Universidad Católica San Antonio de Murcia, Guadalupe, Murcia, Spain
| | - Teresa Gómez-Morte
- Departamento Ciencia y Tecnología de Alimentos, Universidad Católica San Antonio de Murcia, Guadalupe, Murcia, Spain
| | - Pinalysa Cosma
- Dip. Chimica, Università degli Studi "Aldo Moro" di Bari, Bari, Italy
- Consiglio Nazionale delle Ricerche CNR-IPCF, UOS Bari, Bari, Italy
| |
Collapse
|
8
|
Mehta N, Cipullo S, Cocerva T, Coulon F, Dino GA, Ajmone-Marsan F, Padoan E, Cox SF, Cave MR, De Luca DA. Incorporating oral bioaccessibility into human health risk assessment due to potentially toxic elements in extractive waste and contaminated soils from an abandoned mine site. CHEMOSPHERE 2020; 255:126927. [PMID: 32417510 DOI: 10.1016/j.chemosphere.2020.126927] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/27/2020] [Revised: 04/26/2020] [Accepted: 04/27/2020] [Indexed: 05/19/2023]
Abstract
The waste rock, tailings and soil around an abandoned mine site in Gorno (northwest Italy) contain elevated concentrations of potentially toxic elements (PTE) exceeding the permissible limits for residential uses. Specifically, the maximum concentrations of As, Cd, Pb, and Zn were 107 mg/kg, 340 mg/kg, 1064 mg/kg, and 148 433 mg/kg, respectively. A site-specific human health risk assessment (HHRA) was conducted for residential and recreational exposure scenarios, using an approach based on Risk Based Corrective Action (RBCA) method, refined by incorporating oral bioaccessibility data. Oral bioaccessibility analyses were performed by simulating the human digestion process in vitro (Unified BARGE Method). Detailed analysis of oral bioaccessible fraction (BAF i.e. ratio of bioaccessible concentrations to total concentrations on <250 μm fraction) indicated BAF of As (5-33%), Cd (72-98%), Co (24-42%), Cr (3-11%), Cu (25-90%), Ni (17-60%), Pb (16-88%) and Zn (73-94%). The solid phase distribution and mineralogical analyses showed that the variation of BAF is attributed to presence of alkaline calcareous rocks and association of PTE with a variety of minerals. The HHRA for ingestion pathway, suggested that bioaccessibility-corrected cancer risk reached up to 2.7 × 10-5 and 0.55 × 10-5 for residential and recreational senarios respectively (acceptable level is 1 × 10-5). The hazard index (HI) recalculated after incorporation of oral bioaccessible concentrations for a residential scenario ranged from 0.02 to 17.9. This was above the acceptable level (>1) for 50% of the samples, indicating potential human health risks. This study provides information for site-specific risk assessments and planning future research.
Collapse
Affiliation(s)
- Neha Mehta
- Queen's University Belfast, School of Mechanical and Aerospace Engineering, Belfast, BT9 5AH, UK; University of Torino, Department of Earth Sciences, Torino, 10125, Italy.
| | - Sabrina Cipullo
- Cranfield University, School of Water, Energy and Environment, Cranfield, MK43 0AL, UK
| | - Tatiana Cocerva
- Queen's University Belfast, School of Natural and Built Environment, Belfast, BT9 5AG, UK
| | - Frederic Coulon
- Cranfield University, School of Water, Energy and Environment, Cranfield, MK43 0AL, UK
| | | | - Franco Ajmone-Marsan
- University of Torino, Department of Agricultural, Forest and Food Sciences, Grugliasco, 10095, Italy
| | - Elio Padoan
- University of Torino, Department of Agricultural, Forest and Food Sciences, Grugliasco, 10095, Italy
| | - Siobhan Fiona Cox
- Queen's University Belfast, School of Natural and Built Environment, Belfast, BT9 5AG, UK
| | - Mark R Cave
- British Geological Survey, Keyworth, Nottingham, NG12 5GG, UK
| | | |
Collapse
|
9
|
Petrella A, Di Mundo R, Notarnicola M. Recycled Expanded Polystyrene as Lightweight Aggregate for Environmentally Sustainable Cement Conglomerates. MATERIALS (BASEL, SWITZERLAND) 2020; 13:E988. [PMID: 32098376 PMCID: PMC7078601 DOI: 10.3390/ma13040988] [Citation(s) in RCA: 21] [Impact Index Per Article: 5.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 01/20/2020] [Revised: 02/14/2020] [Accepted: 02/20/2020] [Indexed: 11/16/2022]
Abstract
In the present work the rheological, thermo-mechanical, microstructural, and wetting characteristics of cement mortars with recycled expanded polystyrene (EPS) were analyzed. The samples were prepared after partial/total replacement of the conventional sand aggregate with EPS having different grain size and size distribution. Lightness and thermal insulation were relevant features for all the bare EPS composites, despite the mechanical strengths. Specifically, EPS based mortars were characterized by higher thermal insulation with respect to the sand reference due to the lower specific mass of the specimens mainly associated with the low density of the aggregates and also to the spaces at the EPS/cement paste interfaces. Interesting results in terms of low thermal conductivity and high mechanical resistances were obtained in the case of sand-EPS mixtures although characterized by only 50% in volume of the organic aggregate. Moreover, sand-based mortars showed hydrophilicity (low WCA) and high water penetration, whereas the presence of EPS in the cement composites led to a reduction of the absorption of water especially on the bulk of the composites. Specifically, mortars with EPS in the 2-4 mm and 4-6 mm bead size range showed the best results in term of hydrophobicity (high WCA) and no water penetration in the inner surface, due to low surface energy of the organic aggregate together with a good particle distribution. This was indicative of cohesion between the ligand and the polystyrene as observed in the microstructural detections. Such a property is likely to be correlated to the observed good workability of this type of mortar and to its low tendency to segregation compared to the other EPS containing specimens. These lightweight thermo-insulating composites can be considered environmentally sustainable materials because they are prepared with no pre-treated secondary raw materials and can be used for indoor applications.
Collapse
Affiliation(s)
- Andrea Petrella
- Dipartimento di Ingegneria Civile, Ambientale, Edile, del Territorio e di Chimica, Politecnico di Bari, Via E. Orabona, 4, 70125 Bari, Italy; (R.D.M.); (M.N.)
| | | | | |
Collapse
|
10
|
Petrella A, Di Mundo R, De Gisi S, Todaro F, Labianca C, Notarnicola M. Environmentally Sustainable Cement Composites Based on End-of-Life Tyre Rubber and Recycled Waste Porous Glass. MATERIALS (BASEL, SWITZERLAND) 2019; 12:E3289. [PMID: 31658637 PMCID: PMC6829454 DOI: 10.3390/ma12203289] [Citation(s) in RCA: 15] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 09/11/2019] [Revised: 10/01/2019] [Accepted: 10/08/2019] [Indexed: 11/16/2022]
Abstract
In this paper, environmentally sustainable cement mortars were prepared with end-of-life tyre rubber (TR) and recycled waste porous glass (PG) as aggregates in order to obtain lightweight products characterized by renewable and not-pretreated materials specifically for indoor applications. The secondary raw materials were added as partial and/or total replacement of the conventional sand aggregate. The resulting lightweight specimens were characterized by rheological, mechanical, thermal, microstructural and wettability tests. Fine tyre rubber aggregates affected the cohesiveness of the composites, as opposite to coarse tyre rubber and porous glass. The flexural and the compressive strengths of the porous glass samples were higher than the tyre rubber samples because of the higher stiffness and good adhesion of the glass to the cement paste as observed by microstructural observations. On the contrary, an unfavorable adhesion of the tyre aggregates to the cement paste was observed, together with discrete cracks after failure without separation of the two parts of the specimens. The latter result can explain the best results obtained by tyre rubber mortars in the case of impact compression tests where the super-elastic properties of the elastomeric material were evidenced by a deep groove before complete failure. Moreover, the thermal conductivity decrease of the lightweight porous TR and PG composites was in the range of ~80-90% with respect to the sand-based samples, which suggests that they can be used as plasters and masonries, and, in the case of tyre rubber specimens, outside applications are not excluded as observed from the wettability tests.
Collapse
Affiliation(s)
- Andrea Petrella
- Dipartimento di Ingegneria Civile, Ambientale, Edile, del Territorio e di Chimica, Politecnico di Bari, Via E. Orabona 4, 70125 Bari, Italy.
| | - Rosa Di Mundo
- Dipartimento di Ingegneria Civile, Ambientale, Edile, del Territorio e di Chimica, Politecnico di Bari, Via E. Orabona 4, 70125 Bari, Italy.
| | - Sabino De Gisi
- Dipartimento di Ingegneria Civile, Ambientale, Edile, del Territorio e di Chimica, Politecnico di Bari, Via E. Orabona 4, 70125 Bari, Italy.
| | - Francesco Todaro
- Dipartimento di Ingegneria Civile, Ambientale, Edile, del Territorio e di Chimica, Politecnico di Bari, Via E. Orabona 4, 70125 Bari, Italy.
| | - Claudia Labianca
- Dipartimento di Ingegneria Civile, Ambientale, Edile, del Territorio e di Chimica, Politecnico di Bari, Via E. Orabona 4, 70125 Bari, Italy.
| | - Michele Notarnicola
- Dipartimento di Ingegneria Civile, Ambientale, Edile, del Territorio e di Chimica, Politecnico di Bari, Via E. Orabona 4, 70125 Bari, Italy.
| |
Collapse
|