Membrane distillation and pervaporation for ethanol removal: are we comparing in the right way?

Pioneering the preparation of porous PIM-1 membranes for enhanced water vapor flow

In this study, porous polymers of intrinsic microporosity (PIM-1) membranes were prepared by non-solvent induced phase inversion (NIPS) and investigated for water vapor transport in view of their application in membrane distillation (MD). Due to the lack of high boiling point solvents for PIM-1 that are also water miscible, the mixture of tetrahydrofuran (THF) and N-methyl-2-pyrrolidone (NMP) was found to be optimal for the formation of a membrane with a developed porous system both on the membrane surface and in the bulk. PIM-1 was synthesized by using low and high temperature methods to observe how molecular weight effects the membrane structure. Low molecular weight PIM-1 was produced at low temperatures, while high molecular weight PIM-1 was obtained at high temperatures. Several membranes were prepared, including PM-6, PM-9, and PM-11 from low molecular weight PIM-1, and PM-13 from high molecular weight PIM-1. Scanning electron microscopy (SEM) was used to image the surface and cross-section of different porous PIM-1 membranes. Among all the PIM-1 membranes (PM) obtained, PM-6, PM-9, PM-11 and PM-13 showed the most developed porous structure, while PM-13 showed large voids in the bulk of the membrane. Contact angle measurements showed that all PIM-1 porous membranes are highly hydrophobic. Liquid water flux measurements showed that PM-6, PM-9 and PM-11 showed minimal water fluxes due to small surface pore size, while PM-13 showed a high water flux due to a large surface pore size. Water vapor transport measurements showed high permeance values for all membranes, demonstrating the applicability of the developed membranes for MD. In addition, a thin film composite (TFC) membrane with PIM-1 selective layer was prepared and investigated for water vapor transport to compare with porous PIM-1 membranes. The TFC membrane showed an approximately 4-fold lower vapor permeance than porous membranes. Based on these results, we postulated that the use of porous PIM-1 membranes could be promising for MD due to their hydrophobic nature and the fact that the porous membranes allow vapor permeability through the membrane but not liquid water. The TFC membrane can be used in cases where the transfer of water-soluble contaminants must be absolutely avoided.

Synergy of biofuel production with waste remediation along with value-added co-products recovery through microalgae cultivation: A review of membrane-integrated green approach

Development of advanced biofuels such as bioethanol and biodiesel from renewable resources is critical for the earth's sustainable management and to slow down the global climate change by partial replacement of gasoline and diesel in the transport sector. Being a diverse group of aquatic micro-organisms, algae are the most prominent resources on the planet, distributed in an aquatic system, a potential source of bioenergy, biomass and secondary metabolites. Microalgae-based biofuel production is widely accepted as non-food fuel sources and better choice for achieving goals of incorporation of a clean fuel source into the transportation sector. The present review article provides a comprehensive literature survey as well as a novel approach on the application of microalgae for their simultaneous cultivation and bioremediation of high nutrient containing wastewater. In addition to that, merits and demerits of different existing conventional techniques for microalgae culture reactors, harvesting of algal biomass, oil recovery, use of different catalysts for transesterification reactions and other by-products recovery have been discussed and compared with the membrane-based system to find out the best optimal conditions for higher biomass as well as lipid yield. This article also deals with the use of a tailor-made membrane in an appropriate module that can be used in upstream and downstream processes during algal-based biofuels production. Such membrane-integrated system has the potential of low-cost and eco-friendly separation, purification and concentration enrichment of biodiesel as well as other valuable algal by-products which can bring the high degree of process intensification for scale-up at the industrial stage.