Freeze-drying as the post-processing technique improving adsorptive properties of waste Fe/Mn oxides entrapped in polymer beads towards As(III) and As(V)

Selective adsorption of arsenic by water treatment residuals cross-linked chitosan in co-existing oxyanions competition system

Selective adsorption of arsenic in co-existing oxyanions competition systems remains a significant challenge in water treatment due to the limitations of adsorbent materials that often overlook competitive adsorption, resulting in an overestimation of their actual purification potential for target contaminants. In this study, a novel hydrogel bead adsorbent, composed of water treatment residuals (WTRs) and chitosan (Chi), was developed to selectively remove arsenic, while minimizing the interference from phosphate, which is the strongest and most representative competitor in multi-oxyanion systems. The WTRs-Chi beads (WCB) adsorbents were optimized by adjusting the ratios of WTRs:Chi, with characterization results indicating that increased WTR doping improved the degree of crosslinking and the formation of bidentate complexes with enhanced electrostatic selectivity. Importantly, the co-existence of phosphate had minimal adverse effects on arsenic removal compared to other reported adsorbents. The maximum adsorption capacity for As (V) in the binary system was 34.12 mg/g, and the adsorption behavior was fitted well by the pseudo-second-order kinetic model and the extended Langmuir isotherm model. The experimental results, supported by X-ray photoelectron spectroscopy analysis (XPS), revealed that both As (V) and P (V) adsorption in the single system were driven by electrostatic attraction and ligand exchange. However, in the binary system, the inhibition of P (V) adsorption was attributed to competitive desorption caused by electrostatic repulsion, which hindered the formation of inner-sphere complexes. This study provides a practical approach for developing selective adsorbents to address arsenic contamination in complex water environments and promotes the recycling of municipal solid waste.

Preparation of adsorbent based on water treatment residuals and chitosan by homogeneous method with freeze-drying and its As(V) removal performance

Although the chitosan-WTRs particulate adsorbent prepared by embedding method has been proved to have arsenic adsorption capacity, the capacity of it is greatly weakened compared with the original water treatment residuals (WTRs). In this study, WTRs and chitosan were used as raw materials to prepare a new kind of adsorbent beads by a homogeneous method. At the same time, in order to enhance the adsorption capacity and reduce the limitation of kinetics, freeze-drying method was chosen to dry the adsorbent. The WTRs-chitosan beads by homogeneous method (WCB) were characterized by SEM, XRD, XPS and other methods. According to the characterization results, there are regularly arranged pores inside the particles, and the iron in the particles mainly exists in the form of amorphous iron oxyhydroxide. According to the results of batch experiment, the pseudo-second-order kinetic model has a higher degree of fit, indicating that the WCB adsorbs As(V) mainly by chemical adsorption. The maximum adsorption capacity estimated from the Langmuir isotherm model is 42.083 mg/g, which is almost same as the WTRs. Weak acid and neutral conditions are conducive to adsorption, while alkaline conditions have a significant inhibitory effect on arsenic adsorption.

Optimization of hybrid polymer preparation by ex situ embedding of waste Fe/Mn oxides into chitosan matrix as an effective As(III) and As(V) sorbent

A hybrid polymer for deep removal of arsenic from aqueous solutions was obtained by loading of waste Fe/Mn oxides into a chitosan matrix. The process was optimized by studying the influence of selected individual factors and their reciprocal combinations on the adsorptive and physical properties of the product. The influence of chitosan solution concentration, inorganic load amount, the ratio of Fe/Mn oxides to chitosan, and polymer cross-linking degree on kinetics of As(III) and As(V) adsorption was examined. The optimal values of the parameters were chitosan polymer concentration 1.5% w/w, inorganic load to chitosan ratio 1.67, and glutaraldehyde to chitosan amine groups molar ratio 3:1. The selected products were evaluated in terms of their morphology (scanning electron microscopy (SEM) with EDS analysis), porosity (N₂ and CO₂ adsorption isotherms), surface properties (Fourier-transform infrared spectroscopy (FTIR), isoelectric point determination) and durability in an acidic environment. The proposed process makes it possible to obtain a product combining beneficial adsorptive properties toward arsenic with the physical form and durability essential in fixed-bed adsorption systems.