Influence of surfactants on anaerobic digestion of waste activated sludge: acid and methane production and pollution removal

Enhancing biogas production from palm oil mill effluent through the synergistic application of surfactants and iron supplements

In this study, the effects of various surfactants on the soluble chemical oxygen demand (COD) fraction and biogas production from palm oil mill effluent (POME) were investigated. A cationic surfactant (cetyltrimethylammonium bromide, CTAB) and a nonionic surfactant (Tween 80; TW80) were found to adsorb onto the particulate matter from POME, markedly reducing the soluble COD, unlike an anionic surfactant (sodium dodecyl sulfate, SDS). The mechanism underlying this phenomenon might be the adsolubilization of oil on particulate matter induced by the adsorbed surfactants. In terms of biogas production, 0.1 % w/v SDS and CTAB dramatically reduced the biogas yield, while 0.1 % w/v TW80 did not have this negative effect. A synergistic effect was observed when TW80 (0.1 % w/v) was combined with FeSO4 (400 mg/L), resulting in a 17 % greater biogas yield than that achieved with treatments using TW80 or FeSO4 alone. Moreover, the combination of TW80 and FeSO4 increased the biogas production rate. Surprisingly, the water-soluble iron fraction remained consistent across all treatments, suggesting that the adsorption of TW80 on particulate matter may limit micelle formation. Importantly, the proportion of methane in the generated biogas remained stable in all the treatments. Microbial community analysis revealed that the introduction of TW80 and FeSO4 had no discernible impact on the microbial community of the system. Pretreatment with TW80 and an iron supplement significantly enhanced biogas production and reduced the retention time of the anaerobic digestion (AD) system while maintaining the biogas quality and microbial community stability.

Complete biodegradability assessment of polyoxyethylene glycerol ester non-ionic surfactant: Aerobic, anaerobic, combined biodegradation and inhibitory effects

Aerobic and anaerobic biodegradability have become one of the most relevant characteristics for all contaminants. This is especially important in case of surfactants, which are discharged in wastewater treatment plants or directly into the aquatic bodies. The aim of this study is the integral assessment of the biodegradability of the non-ionic surfactant polyoxyethylene glycerol ester PGE-OE17. The aerobic and anaerobic biodegradation of PGE-OE17 was evaluated at different initial surfactant concentrations, and the evolution of the toxicity of the surfactant and its by-products was followed during the aerobic and anaerobic processes using bacteria Vibrio fischeri. PGE-OE17 was not completely biodegradable neither aerobically nor anaerobically, and the increase in the initial surfactant concentration had a negative effect in the biodegradation. Toxicity of the surfactant solutions and degradation by-products had a first increase followed by a gradual decrease during both tests, revealing that toxic substances released can harm the microorganisms and therefore hinder the biodegradation. Additionally, combined aerobic-anaerobic biodegradation tests were performed, consisting in a first aerobic treatment of different duration and initial concentration, followed by a complete anaerobic treatment. Results showed that a balance between aerobic and anaerobic biodegradation duration can maximize the biodegradation rates in comparison with only aerobic or anaerobic tests.

Dual effects of PFOA or PFOS on reductive dechlorination of trichloroethylene (TCE)

PFASs and chlorinated solvents are the common co-contaminants in soil and groundwater at firefighter training areas (FTAs). Although PFASs mixtures could have adverse impacts on bioremediation of trichloroethylene (TCE) by inhibiting Dehalococcoides (Dhc), little is known about the effect and contribution of PFOA or PFOS on dechlorination of TCE by non-Dhc organohalide-respiring bacteria (OHRB). To study this, PFOA and PFOS were amended to the growth medium of a non-Dhc OHRB-containing enrichment culture to determine the impact on dechlorination. This study demonstrated that high levels of PFOA or PFOS (100 mg L^-1) inhibited TCE dechlorination in four non-Dhc OHRB-containing community including Geobacter, Desulfuromonas, Desulfitobacterium, and Dehalobacter, but low levels of PFOA or PFOS (≤10 mg L^-1) enhanced TCE dechlorination. Four non-Dhc OHRB were less inhibited by PFOA than that by PFOS, and high level of PFOS killed Desulfitobacterium and Dehalobacter and decreased the biodiversity of bacterial community. Although most fermenters were killed by the presence of 100 mg L^-1 PFOS, two important co-cultures (Desulfovibrio and Sedimentibacter) of OHRB were enriched, indicating that the syntrophic relationships between OHRB and co-cultures still remained, and PFOA or PFOS inhibited TCE dechlorination by directly repressing non-Dhc OHRB. Our results highlight that the bioattenuation of chloroethene contamination could be confounded by non-Dhc OHRB in high levels of PFOS contaminated subsurface environments at FTAs.

Application and improvement methods of sludge alkaline fermentation liquid as a carbon source for biological nutrient removal: A review

Alkaline fermentation can reduce the amount of waste activated sludge and prepare sludge alkaline fermentation liquid (SAFL) rich in short-chain fatty acids (SCFAs), which can be used as a high-quality carbon source for the biological nutrient removal (BNR) process. This review compiles the production method of SAFL and the progress of its application as a BNR carbon source. Compared with traditional carbon sources, SAFL has the advantages of higher efficiency and economy, and different operating conditions can influence the yield and structure of SCFAs in SAFL. SAFL can significantly improve the nutrient removal efficiency of the BNR process. Taking SAFL as the internal carbon source of BNR can simultaneously solve the problem of carbon source shortage and sludge treatment difficulties in wastewater treatment plants, and further reduce the operating cost. However, the alkaline fermentation process results in many refractory organics, ammonia and phosphate in SAFL, which reduces the availability of SAFL as a carbon source. Purifying SCFAs by removing nitrogen and phosphorus, directly extracting SCFAs, or increasing the amount of SCFAs in SAFL by co-fermentation or combining with other pretreatment methods, etc., are effective measures to improve the availability of SAFL.

The Collision between g-C3 N4 and QDs in the Fields of Energy and Environment: Synergistic Effects for Efficient Photocatalysis

Recently, graphitic carbon nitride (g-C₃ N₄ ) has attracted increasing interest due to its visible light absorption, suitable energy band structure, and excellent stability. However, low specific surface area, finite visible light response range (<460 nm), and rapid photogenerated electron-hole (e^- -h⁺ ) pairs recombination of the pristine g-C₃ N₄ limit its practical applications. The small size of quantum dots (QDs) endows the properties of abundant active sites, wide absorption spectrum, and adjustable bandgap, but inevitable aggregation. Studies have confirmed that the integration of g-C₃ N₄ and QDs not only overcomes these limitations of individual component, but also successfully inherits each advantage. Encouraged by these advantages, the synthetic strategies and the fundamental of QDs/g-C₃ N₄ composites are briefly elaborated in this review. Particularly, the synergistic effects of QDs/g-C₃ N₄ composites are analyzed comprehensively, including the enhancement of the photocatalytic performance and the avoidance of aggregation. Then, the photocatalytic applications of QDs/g-C₃ N₄ composites in the fields of environment and energy are described and further combined with DFT calculation to further reveal the reaction mechanisms. Moreover, the stability and reusability of QDs/g-C₃ N₄ composites are analyzed. Finally, the future development of these composites and the solution of existing problems are prospected.

Physiological Responses of Methanosarcina barkeri under Ammonia Stress at the Molecular Level: The Unignorable Lipid Reprogramming

Acetotrophic methanogens' dysfunction in anaerobic digestion under ammonia pressure has been widely concerned. Lipids, the main cytomembrane structural biomolecules, normally play indispensable roles in guaranteeing cell functionality. However, no studies explored the effects of high ammonia on acetotrophic methanogens' lipids. Here, a high-throughput lipidomic interrogation deciphered lipid reprogramming in representative acetoclastic methanogen (Methanosarcina barkeri) upon high ammonia exposure. The results showed that high ammonia conspicuously reduced polyunsaturated lipids and longer-chain lipids, while accumulating lipids with shorter chains and/or more saturation. Also, the correlation network analysis visualized some sphingolipids as the most active participant in lipid-lipid communications, implying that the ammonia-induced enrichment in these sphingolipids triggered other lipid changes. In addition, we discovered the decreased integrity, elevated permeability, depolarization, and diminished fluidity of lipid-supported membranes under ammonia restraint, verifying the noxious ramifications of lipid abnormalities. Additional analysis revealed that high ammonia destabilized the structure of extracellular polymeric substances (EPSs) capable of protecting lipids, e.g., declining α-helix/(β-sheet + random coil) and 3-turn helix ratios. Furthermore, the abiotic impairment of critical EPS bonds, including C-OH, C═O-NH-, and S-S, and the biotic downregulation of functional proteins involved in transcription, translation, and EPS building blocks' supply were unraveled under ammonia stress and implied as the crucial mechanisms for EPS reshaping.

Insights into the impact of quaternary ammonium disinfectant on sewage sludge anaerobic digestion: Dose-response, performance variation, and potential mechanisms

Wide commercial applications of antimicrobial quaternary ammonium compounds (QACs) inevitably lead to the release into wastewater and enrichment in sewage sludge. This study evaluated the impacts of levels and structures of QACs on sewage sludge properties, microbial community, and methane production during anaerobic digestion. Methane production was stimulated or not affected at low QACs concentrations, but significantly inhibited at high QACs concentrations. Compared with benzyl and alkyltrimethyl QACs, dialkyl QACs showed least toxicity on digestion performance. Meanwhile, microbial community analysis indicated that shifts in bacterial communities mainly depended on QACs doses, but the archaeal communities were affected by both QACs doses and types. The dominant methanogenic pathway shifted from acetotrophic/methylotrophic methanogens to mixotrophic methanogens by low levels of benzyl and alkyltrimethyl QACs but not dialkyl QACs, and further to hydrogenotrophic methanogens at high QACs concentration. Mechanism exploration revealed that the presence of QACs promoted sludge solubilization by the integrated effects of cell lysis, electric neutralization, and hydrophobicity improvement, but inhibited methanogenesis due to the accumulation of volatile fatty acids and susceptibility of methanogens to QACs. These findings provided a reference for potential impacts of different QACs on sludge biological treatment, which had implications for the use and selection of QACs disinfectants.

Successive choline addition enhancing the methanogenesis of waste activated sludge anaerobic digestion: Insight from hydrophilicity, electrochemical performance and microbial community

Anaerobic digestion (AD) is a promising technology to treat waste-activated sludge, previous study proved that methane production could be enhanced with the addition of choline, this work aimed to solve the problem of rapid biodegradability of choline in the AD process by changing its dosing method. With 0.75 g/L as the optimal choline dosing concentration, experimental results showed that successive choline dosing during the first 3-6 days of AD (experimental groups, EGs) performed better than the single dosing. The accumulative biogas production in EGs was increased by 35.55-36.73%, which could be caused by the simultaneous promotion of hydrolysis-acidification and methanogenesis processes. Especially, the electron exchange capacity of digested sludge in EGs was increased by 16.71-34.58%. In addition, the surface Gibbs free energy (△G_SL) of sludge in EGs was 105.51-172.21% higher (corresponding to stronger hydrophilicity and repulsion), which might help disperse sludge flocs and improve mass transfer efficiency, and the △G_SL values were positively correlated with the accumulative methane production (R² = 0.7029). Microbiological analysis showed that microbial communities in EGs were richer and Methanosaeta was regarded as the dominant species with 15.93-30.08% higher relative abundance with choline addition. According to Kyoto Encyclopedia of Genes and Genomes (KEGG) pathway analysis, EGs were found to be more active in metabolism clusters. Collectively, these findings demonstrated that successive choline dosing during the first 3-6 days is an effective and novel method to enhance methane production in AD process.

Influences of specific surfactant structures on biohydrogen production from oily wastewater in batch and continuous anaerobic dark fermentation

Residual oil in palm oil mill effluent (POME) poses difficulties in its treatment chain. Non-ionic surfactants containing different hydrophobic tail structures and their optimal concentrations were evaluated for effectiveness in biohydrogen production. By adding the surfactants at their critical micelle concentration in synthetic oily wastewater, the maximal H₂ yield was increased by 2.2 and 3.5 times for Triton X-100 and Tergitol 15-S-9, respectively, compared to the control. Using real POME, the supplemental Tergitol 15-S-9 resulted in a 56.4 % improvement in H₂ production. For continuous digestion studies, pure POME and Tergitol 15-S-9 supplemented POME (sPOME) were fed to thermophilic anaerobic sequencing batch reactors (ASBRs) under hydraulic retention time (HRT) of 32-12.5 days. Optimally at HRT 19 days, H₂ content in the biogas from sPOME-fed ASBR was noticeably higher, which gave a superior yield of 203.4 mLH₂/gCOD_removed (+15 %).

Primary Sludge from Dairy and Meat Processing Wastewater and Waste from Biomass Enzymatic Hydrolysis as Resources in Anaerobic Digestion and Co-Digestion Supplemented with Biodegradable Surfactants as Process Enhancers

Incorporation of various alternative resources as co-digestion substrates aids to reduce the consumption of agricultural crops for biogas production. However, the efficiency and limitations of these co-substrates is still not fully understood. Use of biomass waste remaining after enzymatic hydrolysis for high value chemical fermentation, meat processing and dairy wastewater primary sludge as co-substrates in an agricultural resource anaerobic digestion plant is tackled within this study. The results showed that anionic surfactants (<200 ppm) can be used to improve fat, oil and grease (FOG) solubility in water and, at the same time, enhance the biomethane potential of FOG-containing sludge by increasing it from 1374.5 to 1765 mLCH4/gVS for meat processing wastewater primary sludge, and from 534 to 740 mLCH4/gVS for dairy wastewater primary sludge, when agricultural digestate is used as a substrate and sludge loading is not more than 10% from the volatile solids loaded. At the same time, only 549.7 mLCH4/gVS was produced as 30-day BMP when 5% biomass hydrolysis waste was used. Biomass hydrolysis waste co-digestion with primary sludge from dairy and meat processing wastewaters has an antigenic effect, and separate substrate anaerobic digestion gave a better results, thus, showing that excessive combination of various waste resources can be inhibitory for biogas production and the appropriate substrate selection and combination is a technical challenge for the biogas industry.

Effects of three surfactants on co-conversion of endogenous carbon and nitrogen of dairy wastewater in mesophilic hydrolytic acidification coupled microalgae culture system

To determine the feasibility of enhancing co-conversion of endogenous C and N in dairy wastewater by surfactants, the effects of varying dosages of sodium lignosulfonate (LS), sodium dodecyl sulfate (SDS), and Tween-80 on mesophilic hydrolytic acidification coupled microalgae culture system were investigated. Tween-80 had a positive effect on hydrolytic acidification, while LS had no clear effect and SDS had a negative effect. Tween-80 significantly increased the C/N ratio in hydrolytic acidification liquor (HAL) (maximum HAc/NH₄⁺-N rate reached 7.90 in 2.9% Tween-80 test). Pyrosequencing analysis demonstrated that community richness and diversity decreased and the proportion of acidobacteria increased with increasing Tween-80 dosage. Furthermore, the effect of Tween-80-enhanced HAL on microalgae (Chlorella pyrenoidosa) growth and nitrogen removal and the assimilation of C and N on the microalgae culture system were investigated. The biomass concentration and a C and N assimilation yield of 4.8% Tween-80 test (1.75 g/L, 825.01 mg/L, 126.68 mg/L) were significantly higher than those of both the low-concentration Tween-80 tests and control. The yield of protein and carbohydrates and higher heating value in the microalgae culture system were also promoted by Tween-80.

Tube wall delamination engineering induces photogenerated carrier separation to achieve photocatalytic performance improvement of tubular g-C3N4

Morphology adjustment is a feasible method to change the physicochemical properties of photocatalysts. The issue that excessively thick tube wall of tubular g-C₃N₄ is not conducive to the electron migration from inside to the surface thus inhibiting the separation of photogenerated carriers has always been ignored. Potassium ions were used to regulate the structure of the tubular supramolecular precursor by breaking hydrogen bonds, thereby promoting the synthesis of delaminated laminar tubular g-C₃N₄ (K-CN), which not only shortened the transfer distance of photogenerated electrons but also provided abundant reaction active sites. Experiments and DFT calculations were combined to reveal the details of the physicochemical properties of K-CN. The photocatalytic capacity of K-CN for tetracycline hydrochloride (TCH) degradation and H₂O₂ generation were 83% and 133 μM, respectively. This work not only synthesized a novel delaminated tubular g-C₃N₄ but also provided a strategy and inspiration for structure and performance optimization for tubular g-C₃N₄.

Distribution patterns of functional microbial community in anaerobic digesters under different operational circumstances: A review

Anaerobic digestion (AD) processes are promising to effectively recover resources from organic wastes or wastewater. As a microbial-driven process, the functional anaerobic species played critical roles in AD. However, the lack of effective understanding of the correlations of varying microbial communities with different operational factors hinders the microbial regulation to improve the AD performance. In this paper, the main anaerobic functional microorganisms involved in different stages of AD processes were first demonstrated. Then, the response of anaerobic microbial community to different operating parameters, exogenous interfering substances and digestion substrates, as well as the digestion efficiency, were discussed. Finally, the research gaps and future directions on the understanding of functional microorganisms in AD were proposed. This review provides insightful knowledge of distribution patterns of functional microbial community in anaerobic digesters, and gives critical guidance to regulate and enrich specific functional microorganisms to accumulate certain AD products.

Microwave-assisted high-efficiency degradation of methyl orange by using CuFe2O4/CNT catalysts and insight into degradation mechanism

Microwave-assisted catalytic oxidation technology has become an effective technology for rapid removal of organic pollutants in wastewater. In this research, the removal of methyl orange (MO) from aqueous solution by CuFe₂O₄ loaded on carbon nanotubes (CuFe₂O₄/CNTs) under microwave irradiation was studied. The effects of different loadings (1:2, 1:4, 1:8) of CuFe₂O₄ on the dielectric loss, magnetic loss, dielectric loss factor, magnetic loss factor, and reflection loss of composite materials were studied. The results showed that the microwave adsorption performance was improved by loading CuFe₂O₄ on CNTs. These different composites were further characterized by SEM, FTIR, and XRD techniques. In addition, this article also studied the effects of different microwave irradiation time, pH, and ionic factors on the degradation of MO. In particular, the mechanism of MO degradation by composite materials under different pH conditions was also studied in detail. The results showed that the removal rate reaches 97% with 5 min under the best conditions, and the composite material had good anti-interference performance. This study may provide a new option to degrade organic dye in wastewater treating.

High-solid digestion from cellulosic ethanol stillage with activated sludge of simultaneous propionate degradation and methanogenesis

High solid anaerobic digestion (HSAD) was an emerging bioconversion technology which had the advantages of small digester, less digestate and low heating energy. A one-stage anaerobic system in CSTR by inoculating activated sludge of simultaneous propionate degradation and methanogenesis was proposed to improve the high-solid digestion performance and to stabilize the reaction process. Semi-continuous mode was successfully used to perform HSAD from cellulosic ethanol whole stillage at an initial substrate loading of 15.4% (w/w) dry matter content with different OLRs from 1.5 to 5.0 gVS·L^-1 d^-1 at an HRT of 30 days. The average methane yield during whole digestion reached 349.9 mL⋅gVS^-1 with a total VS removal rate of 61.3%. The acclimation mechanism of multifunctional activated sludge was also explored by analyzing the functional property, physiological activity and microbial community structure. The results indicated the feasibility and efficiency of multifunctional activated sludge in a semi-continuous high-solid stirred tank reactor system.

Comprehensive insight into surfactant modified-PBAT physico-chemical and biodegradability properties

This work aimed to prepare surfactant modified-PBAT (poly(butylene adipate-co-terephthalate)) sheets with superior properties to increase the PBAT applicability and be a possible solution for plastic disposal environmental problems. Three different surfactant contents (0, 1, 5, and 10 wt%) were investigated, and their effects on PBAT chemical structure, mechanical and morphological properties, wettability, and water absorption were investigated. Modified-PBAT samples showed high hydrogen bond coefficients (0.57) than the pristine PBAT (0.54), indicating an excellent electrostatic interaction between both components and the formation of a rigid hydrogen-bonded network, as confirmed by mechanical tests, where the elastic modulus values for PBAT and PBAT+10% surfactant were 44 and 60 MPa. SEM images and roughness measurements showed changes in PBAT morphology after surfactant addition, improving the roughness and wettability by the voids and polar groups presence, altering the water absorption (WA) behavior. The higher water affinity resulted in high water absorption for PBAT-10%S (17%) compared to the pristine PBAT (2%), which improves hydrolysis tendency, which is the initial step to biodegradation. Biodegradation results indicated that the roughness and WA behavior influenced the biodegradation rate, facilitating hydrolysis and microbial attack, and accelerating modified samples weight loss. Our results suggested developing a material with superior mechanical properties, mainly for PBAT-10%S, that can be applied in several applications, such as packaging and furniture. After discharge, it is not an environmental problem, being a biodegradable material with a green character.

Surfactant-assisted thermal hydrolysis off waste activated sludge for improved dewaterability, organic release, and volatile fatty acid production

The surfactant-assisted thermal hydrolysis pretreatment (THP) of waste activated sludge (WAS) was investigated, focusing on the effect of the surfactant addition on the results of sludge disintegration, dewaterability, organic release, and production of volatile fatty acids (VFAs) via fermentation. Typical anionic surfactant sodium dodecyl sulfate (SDS) and cationic surfactant cetyl trimethyl ammonium bromide (CTAB) were used for the THP experiments. The supernatant of the THP-treated sludge was anaerobically fermented to determine its potential VFAs yield. The results showed that the surfactant addition, particularly CTAB, enhanced the hydrolysis and organic solubilization of the sludge during THP. CTAB addition led to a 36% increase of dissolved organic and a 27% increase of VFAs production. For the THP-treated sludge with the surfactant addition, its dewaterability was also greatly improved. When the CTAB dosage increased from 0 to 0.10 g/g VSS, the minimum capillary suction time (CST) of the sludge decreased from 205 to 50 s/g TSS, and the sludge particles became smaller and less negative with the zeta potential changing from -12.4 to -8.2 mV. Analysis of extracellular polymeric substances (EPS) of the sludge revealed that the surfactant addition increased the sludge disintegration and organic dissolution during the THP process. The surfactant-assisted THP is shown to be a promising technology to enhance the WAS treatment for improved sludge dewaterability, waste reduction, and resource recovery.

In-situ self-assembly construction of hollow tubular g-C3N4 isotype heterojunction for enhanced visible-light photocatalysis: Experiments and theories

A highly reactive hollow tubular g-C₃N₄ isotype heterojunction (SCN-CN) was designed to enhance visible light absorption and manipulate the directed transfer of electrons and holes. The results of UV-vis DRS, XPS valence band and DFT theoretical calculations indicated S doping increases the visible-light absorption capacity and changed the ba nd gap structure of g-C₃N₄ (CN), resulting in the transfer of electrons from the CN to the SCN and holes from the SCN to the CN under visible light. In addition, the tubular structure of the SCN-CN facilitated the transfer of electrons in the longitudinal direction, which reduced charge carrier recombination. Furthermore, the optical properties, electronic structure, and electron transfer of SCN-CN were also studied by experiments and theoretical calculations. The antibiotic tetracycline hydrochloride (TCH) and dye Rhodamine B (RHB) were subjected to evaluate the photocatalytic performance of SCN-CN. The scavenger tests and ESR data showed that the h⁺, ·O₂^- and ·OH worked together in the photocatalytic process. Moreover, the photocatalytic degradation pathway was analyzed by LC-MS. This study synthesized a hollow tubular CN isotype heterojunction with high visible-light photocatalytic performance and provided a theoretical basis for CN isotype heterojunction.

Influence of polyether sulfone microplastics and bisphenol A on anaerobic granular sludge: Performance evaluation and microbial community characterization

The retention of polyether sulfone (PES) and bisphenol A (BPA) in wastewater has received extensive attention. The effects of PES and BPA on the removal of organic matter by anaerobic granular sludge were investigated. We also analyzed the changes in the electron transport system and the effects on the composition of extracellular polymeric substances (EPS), as well as alternations of the microbial community in the anaerobic granular sludge. In the experimental groups which received BPA, the removal of the chemical oxygen demand (COD) were significantly suppressed, which an average removal efficiency of less than 65%, 30% lower than that of the control group. In the loosely-bound EPS (LB-EPS) excitation-emission matrix (EEM) spectra, the absorption peak of tryptophan disappeared when the BPA pollutants was added, which it was present in the control group without added pollutants. The addition of PES and BPA also affected protease, acetate kinase, and coenzyme F₄₂₀ activities in the anaerobic granular sludge. Especially, the coenzyme F₄₂₀ reduced from 0.0045 to 0.0017 μmol/L in the presence of PES and BPA. The relative abundance of Spirochaetes decreased in the presence of PES and BPA, while the relative abundance of Bacteroidetes increased from 12.98% to 22.87%. At the genus level, in the presence of PES and BPA, the relative abundance of Acinetobacter increased from 2.20% to 9.64% and Hydrogenophaga decreased sharply from 15.58% to 0.12%.

Potential influences of exogenous pollutants occurred in waste activated sludge on anaerobic digestion: A review

Anaerobic digestion is a promising approach for waste activated sludge (WAS) disposal. However, a wide range of exogenous pollutants (e.g. heavy metals, nanoparticles) exists in WAS and their influences on anaerobic digestion are neglected. This study investigates the correlations between exogenous pollutants and anaerobic digestion performance. The results indicate that exogenous pollutants exhibit dose-dependent influences on WAS digestion. Most of the pollutants improve the performance of anaerobic digestion by partially or wholly promoting the hydrolysis, acidification and methanogenesis processes at low dose, but exhibit negative effects at high levels due to their toxicity. Generally, methanogens are more vulnerable than those hydrolytic and acidogenic bacteria. Poly-aluminum chloride and polyacrylamide show strong inhibition on WAS digestion, which are primarily attributed to their physical enmeshments of organic matters in WAS. The synergistic effects of different mixed pollutants and the mitigating strategies for typical pollutants inhibition deserve more attention in light of WAS anaerobic digestion.