Superior adsorption and removal of industrial dye from aqueous solution via magnetic silver metal-organic framework nanocomposite

Adsorption and removal of Pb (II) via layer double hydroxide encapsulated with chitosan; synthesis, characterization adsorption isotherms, kinetics, thermodynamics, & optimization via Box-Behnken design

The study aimed to enhance the stability and efficiency of removing bivalent Pb(II) by encapsulating AlNi-layered double hydroxide (LDH) in chitosan and itaconic acid to create an adsorbent with chemically active sites. The resulting material, AlNi-LDH/CS, underwent thorough property analysis using XRD, FT-IR, XPS, EDX, N2 adsorption/desorption isotherm, and FESEM to find out what textural characteristics it has. Specifically, nitrogen adsorption/desorption isotherms were utilized to assess the textural properties of AlNi-LDH/CS. The Al/Ni-LDH/CS surface displayed a specific surface area of 71.95 m2/g and an average pore size of 2.537 nm, consistent with the platelets' external surface. The effects of dose, pH, temperature, and starting concentration on the adsorption process were also investigated in this study. The adsorption characteristics have been examined by means of equilibrium and adsorption kinetics. The adsorption process adhered to the pseudo-second-order and Langmuir isotherm models. The predominant adsorption process was found to be chemisorption, which had an adsorption energy of 28.42 kJ·mol-1. An endothermic and spontaneous adsorption process is suggested by the increase in metal absorption at increasing temperatures. The Box-Behnken design software was utilized to establish the optimal adsorption parameters as pH 5, a dosage of 0.2 g of AlNi-LDH/CS per 25 mL, and an adsorption capacity of 453.05 mg/g for the Pb(II) arsenate solution. For the composite sponge to be most effective in adsorbing arsenate and be used in water purification procedures, these factors are essential. The adsorption process was successfully improved with few planned tests by applying the Box-Behnken design and response surface technique aspects of the Design-Expert software. An evaluation of the adsorbent's reusability using six successive cycles of adsorption and desorption confirmed its stability and showed no discernible decrease in removal efficiency. Additionally, it retained its original chemical composition before and after reuse, showcased consistent efficiency, and maintained uniform XRD data.

Synthesis, characterization and adsorption optimization of bimetallic La-Zn metal organic framework for removal of 2,4-dichlorophenylacetic acid

To eliminate the hazardous pesticide 2,4-dichlorophenylacetic acid (2,4-D) through aqueous solutions, stacked nanorods known as hetero bimetallic organic frameworks (MOFs) of 2-methyl imidazole based on lanthanum and zinc are created. The research's convincing discoveries displayed that La/Zn-MOF is an actual adsorbent for the removal of 2,4-D through aqueous solutions. The La/Zn-MOF was investigated using a variability of techniques, with scanning electron microscope (SEM), powered X-ray diffraction (PXRD), and Brunauer-Emmett-Teller (BET) investigation. La/Zn-MOF has a significant pore capacity of 1.04 cm³/g and a comparatively large surface area of 897.69 m2/g. Our findings, which are quite intriguing, demonstrate that adsorption behavior is pointedly wedged by variations in pH. A pH 6 dose of 0.02 g was shown to be the optimal setting for the greatest capacity for adsorption. Because adsorption is an endothermic process, temperature variations affect its capability. The adsorption method was fit both isothermally and kinetically using the Langmuir isotherm classical. It was created that the entire process made use of a chemisorption mechanism. Solution pH, temperature, adsorbent dosage, and time were all improved using the Box-Behnken design (BBD) and Response Surface Methodology (RSM). We were able to accurately calculate the values of ΔHo, ΔSo, and ΔGo for 2,4-D by following the guidelines. These results demonstrated the spontaneous and endothermic character of the adsorption procedure employing La/Zn-MOF as an adsorbent. Adsorption-desorption cycles can be carried out up to five times. With the synthesized La/Zn-MOF adsorbent due to its exceptional reusability. Many processes, such π-π interaction, pore filling, H-bonding, or electrostatic contact, were postulated to explain the connection between La/Zn-MOF and 2,4-D after extra research to appreciate well the link was conducted. This is the first study to demonstrate the effectiveness of utilizing La/Zn-MOF as an adsorbent to eliminate 2,4-D from wastewater models. The results display that a pH of 6 is required to achieve the maximal 2,4-D adsorption capability on La/Zn-MOF, which is 307.5 mg/g.

Tailoring magnetic Sn-MOFs for efficient amoxicillin antibiotic removal through process optimization

This study investigated the efficacy of magnetic Sn metal-organic frameworks (MSn-MOFs) in removing the insecticide amoxicillin (AMX) from aqueous solutions. Our thorough experimental investigation showed that MSn-MOFs were an incredibly effective adsorbent for removing AMX. Several methods were used to characterize the material. BET investigation of the data displayed a significant surface area of 880 m2 g-1 and a strong magnetic force of 89.26 emu g-1. To identify the point of zero charge, surface characterization was carried out and the value was 7.5. This shows that the adsorbent carries a positive and negative charge below and above this position, respectively. Moreover, the impact of pH on adsorption equilibrium was explored. The results of kinetic models to explore the adsorption of AMX on MSn-MOFs supported the pseudo-second-order, and the adsorption complied well with the Langmuir isotherm. The results revealed that the overall adsorption mechanism may entail chemisorption via an endothermic spontaneous process with MSn-MOFs. The precise modes by which MSn-MOFs and AMX interacted may involve pore filling, H-bonding, π-π interaction, or electrostatic interaction. Determining the nature of this interaction is essential in understanding the adsorption behavior of the MOFs and optimize the adsorbent design for real-world applications. The use of the MSn-MOF adsorbent provides a straightforward yet efficient method for the filtration of water and treatment of industrial effluents. The results showed 2.75 mmol g-1 as the maximum capacity for adsorption at pH = 6. Additional tests were conducted to assess the adsorbent regeneration, and even after more than six cycles, the results demonstrated a high level of efficiency. The adsorption results were enhanced by the application of the Box-Behnken design.

Facile synthesis of new metal-organic framework/chitosan composite sponge for Hg(II) removal: Characterization, adsorption efficiency, and optimization using Box-Behnken design

The objective of this research was to develop a novel adsorbent to eliminate mercury (Hg(II)) from water. A unique citrate-crosslinked La-MOF/citrate crosslinked chitosan composite sponge (La-MOF@CSC composite sponge) was successfully synthesized in an acidic environment using a one-step technique. Modifying the composition of adsorbent materials is a commonly employed strategy to enhance adsorption capacity, particularly for materials composed of metal-organic frameworks. The study investigated the impact of the composite sponge on the adsorption and removal of Hg(II). The composite sponge exhibited a maximum adsorption capacity (qmax) for Hg(II) at 765.22 mg/g and an impressive high surface area of 1208 m2/g. Various factors influencing the adsorption capacity were taken into account in this study. The adsorption isotherm and kinetics were modeled using Langmuir and pseudo-second-order equations, respectively. Consistent with thermodynamics, the adsorption process was identified as spontaneous and endothermic. The quantities of adsorbed substances increased with rising temperature. The La-MOF@CSC composite sponge demonstrated the ability to be reused up to five times with satisfactory efficiency, retaining its chemical composition and exhibiting similar XRD and XPS data before and after each reuse. The interaction between heavy metals and the La-MOF/CSC composite sponge was examined. Optimization of the adsorption outcomes was conducted using the Box-Behnken design (BBD).

Malachite green (cationic dye) removal with modified Pinus brutia biochar

Dyes are frequently used in industries such as textile, leather, paper and printing, to water sources causes harmful effects on the environment and human health. Therefore, it is crucial to effectively remove colored contaminants from water in order to protect the environment and public health, maintain biodiversity and preserve the esthetic aspects of water resources. In this study, wood chips obtained from Pinus brutia (PB) tree grown in many parts of the world were turned into biochar and then modified and used for the removal of malachite green, a cationic dye. For this purpose, biochar (PBB) was made by collecting PB wood and turning it into chips (PB). Later, PBB was modified to gain nano-magnetic properties. The structure of the obtained PBB and nM-PBB adsorbents was characterized by FT-IR. pH (2-9), temperature (25 °C-55 °C), time change (15 min-240 min), adsorbent amount change (0.05 g-0.45g) and MG concentration (25 mg/L-250 mg/L) were investigated in MG removal of PBB and nM-PBB. The process was found to be pseudo-second-order and spontaneous endothermic reaction. PBB and nM-PBB were found to be suitable for Langmuir isotherm in MG removal (qmax=13.004 mg/g for PBB, qmax=18.215 mg/g for nM-PBB).

Effective application of citric acid treated Trapa natans and Citrullus lanatus lignocellulosic macromolecules for adsorptive remediation of acid Violet-7 dye

The peels of Trapa natans (TRA) and Citrullus lanatus (CIT), were modified with a variety of chemicals to boost their surface for the optimization of adsorption performance by providing a greater number of additional active binding sites. Citric acid-processed peels (TRAC and CITC) had shown more favorable adsorption performance to eradicate acid violet 7 dye (AVS). Extra and additional active sites generated after chemical processing, including hydroxyl (OH), carboxyl (COOH), amines NH2, carbonyl, and ester (-O-CO-) groups, as evidenced from FTIR and SEM characterizations, may boost the potential of physicochemical integration of adsorbent surface activity in order to promote and encourage the retention of hazardous and risky AVS molecules from the water. The Langmuir isotherm assessed the qmax for the adsorption of AVS on TRAC, CITC, TRA, and CIT to be 212.8, 294, 24.3, and 60.6 mg/g, respectively, whereas the correlation coefficients assessed for both TRAC and CITC were 0.98 and for TRA and CIT were 0.97, closer to unity reflecting monolayer physio-sorption. According to Temkin, the adsorption of AVS on TRAC, TRA, CITC, and CIT gives "BT" values of 1.275, 0.947, 1.085, and 1.211 mg/g, also suggesting physio-sorption. Therefore, chemically modified peels can be employed for detoxification of AVS.

Direct Growth of Nitrogen-Doped Carbon Quantum Dots on Co9S8 Passivated on Cotton Fabric as an Efficient Photoelectrode for Water Treatment

Heterogeneous growth of photocatalysts on different porous substrates is a solution to avoid secondary pollution caused by composite photocatalysts themselves. However, the heterogeneous growth of composite photocatalysts with nitrogen-doped carbon quantum dots (NCQDs) inclusions-introduced during synthesis-impedes the direct growth on the substrate. To overcome this problem, NCQDs were grown on a Co9S8 (NCQDs-G@Co9S8) layer, decorated on cotton fabric. This optimal coupling mode of NCQDs and Co9S8 showed 54% degradation, compared to 33% dye degradation via NCQDs-doped Co9S8 (NCQDs-D@Co9S8). The change in the crystal structure and its lower loading on fabric results in significantly lower performance of NCQDs-D@Co9S8. Even with the combination of both surface growth and doping (NCQDs-DG@Co9S8), the performance was still limited to 42%. In addition, the optimum growth concentration of NCQDs on Co9S8 was observed for 7.5 w/w %, resulting in 92% photocatalytic activity (PCA) in 80 min. Comparing different surface states formed in NCQDs using different solvents, water-based surface states (oxygen-rich surface) are most suitable for the dye degradation. NCQDs-G@Co9S8 also offers 67% Cr-VI reduction to Cr-III, showing its suitability for both inorganic and organic compounds. Better electrode performance was related to suitable charge separation of the composite, where -OH groups mainly contribute in the photocatalytic dye degradation..

Efficient Adsorption and Removal of the Herbicide 2,4-Dichlorophenylacetic Acid from Aqueous Solutions Using MIL-88(Fe)-NH2

Metal-organic frameworks (MOFs), a material known for its multifunctionality, chemical stability, and high surface area, are now commonly utilized as an adsorbent for water treatment. The MOF (MIL-88(Fe)-NH2) was synthesized and used to remove the commonly used toxic herbicide 2,4-dichlorophenoxyacetic acid (2,4-D) from water. The MIL-88(Fe)-NH2 MOF was fully characterized using multiple techniques. A systematic investigation was conducted to evaluate the key parameters that impact the adsorption process, which include coexisting anions, adsorbent dosage, and solution pH. The adsorption isotherm was fitted using the Langmuir model, while the kinetics were fitted using pseudo-second-order. The adsorption process was both chemisorption and endothermic. The capacity for adsorption increased with rising temperatures. The MIL-88(Fe)-NH2 adsorbent has a maximum adsorption capacity of 345.25 mg g-1 for removing 2,4-D, significantly higher than previous adsorbents used for this purpose. The adsorption mechanism could be ascribed to hydrogen bonding, pore filling, π-π conjugations between the 2,4-D molecules and the MIL-88(Fe)-NH2 adsorbent, and electrostatic interactions. Furthermore, the adsorption capacity of MIL-88(Fe)-NH2 adsorbent showed only a slight decrease after five successive recycles, and it could be easily regenerated through solvent washing. When used in environmental water samples, especially those containing electronic wastes, the MIL-88(Fe)-NH2 adsorbent demonstrated satisfactory adsorption capacity and reusability. The MIL-88(Fe)-NH2 adsorbent is more practical and reusable and has better adsorption capacity and shorter equilibrium time compared to previously reported adsorbents.

Utilizing biochar to decorate nanoscale FeS for the highly effective decontamination of Se(IV) from simulated wastewater

Selenium (Se) as an essential nutrient for human beings at trace concentrations, the allowable concentration for the human is only 40 μg/L. Iron sulfide (FeS) nanoparticles have been applied for excessive of selenium (Se) remediation in surface water and groundwater. In this study, FeS nanoparticles were anchored onto biochar (BC) to reduce agglomeration of FeS and prepared into the composite of FeS-BC by pyrolysis to economically and efficiently remove Se(IV) from simulated wastewater based on the excellent performance of FeS and the low cost of BC. Characterizations presented the uniform anchorage of FeS on the BC surface to prevent agglomeration. The results of batch experiments revealed that the removal of Se(IV) by FeS-BC nanomaterials significantly depended on the pH value, with the maximum removal of ∼174.96 mg/g at pH 3.0. A pseudo-second-order kinetic model well reflected the kinetic removal of Se(IV) in pure Se(IV) solution with different concentration, as well as the coexistence of K+, Ca2+, Cl-, and SO42- ions. The presence of K+ ions significantly inhibited the removal of Se(IV) with the increase of K+ ion concentration compared with the effect of the other three ions. SEM-EDS and XPS analyses indicated that the removal process was achieved through adsorption by surface complexation, and reductive precipitation of Se(IV) into Se0 with the electron donor of Fe(II) and S(-II) ions. The FeS-BC nanomaterial exhibited an excellent application prospect in the remediation of Se(IV).

Efficient Removal of Deltamethrin from Aqueous Solutions Using a Novel Lanthanum Metal-Organic Framework: Adsorption Models and Optimization via Box-Behnken Design

Eliminating pesticides is essential for lowering the dangers to our environment. To do this effectively, it is crucial to find adsorbents with remarkable adsorption capacities, easy retrieval, and separation. Metal-organic frameworks (MOFs) have been extensively recognized for their exceptional ability to absorb pollutants. Therefore, we used novel lanthanum metal-organic frameworks (La-MOFs) to eliminate deltamethrin (DEL) from aqueous solutions. We proved through experimentation that the La-MOF is an efficient adsorbent for DEL from water. A study of the material revealed that the adsorbent had a surface area of 952.96 m2 per gram and a pore volume of 1.038 cm3/g. These outcomes show how this substance can absorb particles. Utilizing kinetic models and conforming to the pseudo-second-order model, a thorough analysis of the efficiency of DEL adsorption onto La-MOF was conducted. To create a perfectly tailored approach, we utilized many parameters. The synthetic La-MOF adsorbent may undergo up to five steps of adsorption-desorption and has exceptional cyclability and reusability. To confirm purifying wastewater samples in the laboratory, the presentation of the established adsorbent was evaluated. For the management of industrial effluent and water filtration, the La-MOF adsorbent offered a simple and effective solution. Our investigation suggests that the method we describe for removing DEL from wastewater samples using the La-MOF adsorbent is unique.

Application of Metal-Organic Frameworks for Efficient Removal of Doxorubicin Hydrochloride: Removal Process Optimization and Biological Activity

This study looked at the doxorubicin hydrochloride (DOX) anticancer drug's adsorption characteristics on a silver-based metal-organic framework (Ag-MOF). X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) were used for the characterization of Ag-MOF. The pore volume and surface area of Ag-MOF were determined through Brunauer-Emmett-Teller (BET) testing at 77 K to be 0.509 cm3/g and 676.059 m2/g, respectively. Adsorption at pH 6 was established to be the best for DOX compared to alkaline solution. Ag-MOF has a good capacity for eliminating DOX (1.85 mmol/g), according to adsorption experiments. From the adsorption results, we can find that Langmuir is the most fitted adsorption isotherm model and the pseudo-second order model best fitted the adsorption kinetics. The energy of activation for adsorption, which was determined to be 15.23 kJ/mol, also supported a chemisorption process. The mechanism of adsorption was evaluated, and details of all possible interactions between DOX and Ag-MOF were illustrated. On the other hand, while examining the impact of temperature, we identified the thermodynamic constraints as ΔG°, ΔH°, and ΔS° and confirmed that the reaction was an endothermic one and spontaneous. Even after numerous reuse cycles, the efficiency remained constant. The synthetic adsorbent was remarkably recyclable at a rate of more than 91.6%. By using the MTT assay, the cytotoxicity of the tested Ag-MOF and DOX@Ag-MOF against human breast cancer cells (MCF-7) was evaluated in vitro. The in vitro antimicrobial activity of Ag-MOF and DOX@Ag-MOF was also tested.