Finite element analysis of stress distribution in intact and porcelain veneer restored teeth

Correlation of mineral density and elastic modulus of dog dentin using μ-CT and nanoindentation

This study sought to 1) investigate the spatial distribution of mineral density of dog dentin using µ-CT and 2) characterize the relationship between the elastic modulus and mineral density of dog dentin using nanoindentation and µ-CT. Maxillary canine teeth of 10 mature dogs were scanned with a µ-CT then sectioned in the transverse and vertical planes and tested using nanoindentation. Spatial distribution of mineral density and elastic modulus was quantified. Results demonstrated significant spatial variation in mineral density and elastic modulus. Mineral density and elastic modulus generally increased from the dentin-pulp interface to the dentino-enamel junction and from the crown base to the crown tip. Significant site dependent correlations between mineral density and elastic modulus were determined (0.021 > R2 > 0.408). The results of this study suggest that while mineral density is a mediator of elastic modulus, other mediators such as collagen content may contribute to the mechanical behavior of dog dentin.

Influence of glass fiber posts on the fracture susceptibility of endodontically treated maxillary anterior teeth with direct veneers: Preliminary results of a randomized clinical trial

OBJECTIVE

The purpose of this randomized clinical trial was to evaluate the influence of glass fiber posts on fracture susceptibility of endodontically treated maxillary anterior teeth with direct veneers.

MATERIALS AND METHODS

Fifty participants had 1 maxillary anterior tooth restored with a direct veneer. They were divided into 2 groups (n = 25) according to the use of intraradicular glass fiber posts. Clinical evaluation was performed at baseline, 6 and 12 months. The treatment success was determined by the absence of tooth fracture. If there was fracture, it was classified according to its extent. Fischer exact test was performed to analyze the criteria among the groups at each evaluation time. Friedman repeated analysis of variance assessed the difference in the performance of each group at three recall times (α = 0.5).

RESULTS

For control group, at the 6-month follow-up, one tooth had suffered a catastrophic failure, which resulted in tooth extraction. Fisher statistical analysis showed no significant difference between the cumulative success rate of the groups for the 6 (P > .999) and the 12-month (P > .999) period. Friedman test showed no significant difference among the periods of evaluation (P > .999).

CONCLUSIONS

Both groups had a similar success rate for maxillary anterior endodontically treated teeth with direct veneers after 12 months.

CLINICAL IMPLICATIONS

Glass fiber post use does not influence the fracture susceptibility of maxillary anterior endodontically treated teeth with direct veneers in the short term.

Influence of Preparation Depth and Design on Stress Distribution in Maxillary Central Incisors Restored with Ceramic Veneers: A 3D Finite Element Analysis

PURPOSE

To evaluate the influence of different preparation designs and depths on the stress field developed in maxillary central incisors restored with veneers made with different ceramic materials using finite element analysis (FEA).

MATERIALS AND METHODS

A linear static three-dimensional finite element analysis model was used with the aid of reverse engineering to develop digital models of maxillary central incisors restored with ceramic veneers, according to two different preparation depths (thin vs deep) and two different preparation designs (feather edge vs butt joint). Three ceramic systems were tested: (i) feldspathic porcelain, (ii) heat pressed glass ceramic IPS Empress 2 (Ivoclar Vivadent AG), and (iii) heat pressed glass ceramic IPS e.max-Press (Ivoclar Vivadent AG). Each model was subjected to a compressive force of 200N applied to the palatal surface 2 mm below the incisal edge. The longitudinal axis of the restored tooth formed an angle of 130^o with the direction of the force. The biomechanical behavior of the different models was examined according to the von Mises stress criterion. Statistical analysis was performed using nonparametric confidence interval estimation using bootstrapping.

RESULTS

The maximum observed stress values were calculated and found to be similar between prepared and intact teeth. The cervical margin of the veneers displayed the highest von Mises stress values. Irrespectively of the depth and preparation design, the biggest von Mises stress values were observed at the veneer structures with the following order: (i) IPS Empress 2, (ii) IPS e.max-Press, (iii) feldspathic (p = 0.001). Preparation depth resulted in statistically significant differences (p = 0.001) in the stress distribution in the majority of tested structures. As the preparation depth was increased, the stresses within the veneer structure and the tooth structures were decreased. No statistically significant differences were detected in the stresses among the different restored models, when the preparation design was considered.

CONCLUSIONS

This FEA study suggests that ceramic veneers could restore the biomechanical behavior of prepared central incisors and made it similar of that of an intact tooth. Regardless of the preparation depth and design and the ceramic system used, the cervical margin of ceramic veneers presents the highest von Mises stress values. When feldspathic porcelain was compared with lithium disilicate (IPS e.max Press), the latter displayed the lowest transfer of stresses to dental tissues. An increase in preparation depth resulted in a statistically significant stress decrease in both the veneer and the tooth.

Thermal-stress analysis of ceramic laminate veneer restorations with different incisal preparations using micro-computed tomography-based 3D finite element models

Main objective of this study is to investigate the thermal behavior of ceramic laminate veneer restorations of the maxillary central incisor with different incisal preparations such as butt joint and palatinal chamfer using finite element method. In addition, it is also aimed to understand the effect of different thermal loads which simulates hot and cold liquid imbibing in the mouth. Three-dimensional solid models of the sound tooth and prepared veneer restorations were obtained using micro-computed tomography images. Each ceramic veneer restoration was made up of ceramic, luting resin cement and adhesive layer which were generated based on the scanned images using computer-aided design software. Our solid model also included the remaining dental tissues such as periodontal ligament and surrounding cortical and spongy bones. Time-dependent linear thermal analyses were carried out to compare temperature changes and stress distributions of the sound and restored tooth models. The liquid is firstly in contact with the crown area where the maximum stresses were obtained. For the restorations, stresses on palatinal surfaces were found larger than buccal surfaces. Through interior tissues, the effect of thermal load diminished and smaller stress distributions were obtained near pulp and root-dentin regions. We found that the palatinal chamfer restoration presents comparatively larger stresses than the butt joint preparation. In addition, cold thermal loading showed larger temperature changes and stress distributions than those of hot thermal loading independent from the restoration technique.

Three-dimensional finite element analysis of stress distribution in retention screws of different crown-implant ratios

The retaining screw of the implant-supported dental prosthesis is the weakest point of the crown/implant system. Furthermore, crown height is another important factor that may increase the lever arm. Therefore, the aim of this study was to assess the stress distribution in implant prosthetic screws with different heights of the clinical crown of the prosthesis using the method of three-dimensional finite element analysis. Three models were created with implants (3.75 mm × 10 mm) and crowns (heights of 10, 12.5 and 15 mm). The results were visualised by means of von Mises stress maps that increased the crown heights. The screw structure exhibited higher levels of stresses in the oblique load. The oblique loading resulted in higher stress concentration when compared with the axial loading. It is concluded that the increase of the crown was damaging to the stress distribution on the screw, mainly in oblique loading.