Virtual human hand: model and kinematics

Quantitative Assessment of Hand Function in Healthy Subjects and Post-Stroke Patients with the Action Research Arm Test

The Action Research Arm Test (ARAT) can provide subjective results due to the difficulty assessing abnormal patterns in stroke patients. The aim of this study was to identify joint impairments and compensatory grasping strategies in stroke patients with left (LH) and right (RH) hemiparesis. An experimental study was carried out with 12 patients six months after a stroke (three women and nine men, mean age: 65.2 ± 9.3 years), and 25 healthy subjects (14 women and 11 men, mean age: 40.2 ± 18.1 years. The subjects were evaluated during the performance of the ARAT using a data glove. Stroke patients with LH and RH showed significantly lower flexion angles in the MCP joints of the Index and Middle fingers than the Control group. However, RH patients showed larger flexion angles in the proximal interphalangeal (PIP) joints of the Index, Middle, Ring, and Little fingers. In contrast, LH patients showed larger flexion angles in the PIP joints of the Middle and Little fingers. Therefore, the results showed that RH and LH patients used compensatory strategies involving increased flexion at the PIP joints for decreased flexion in the MCP joints. The integration of a data glove during the performance of the ARAT allows the detection of finger joint impairments in stroke patients that are not visible from ARAT scores. Therefore, the results presented are of clinical relevance.

Hand Motion Analysis during the Execution of the Action Research Arm Test Using Multiple Sensors

The Action Research Arm Test (ARAT) is a standardized outcome measure that can be improved by integrating sensors for hand motion analysis. The purpose of this study is to measure the flexion angle of the finger joints and fingertip forces during the performance of three subscales (Grasp, Grip, and Pinch) of the ARAT, using a data glove (CyberGlove II^®) and five force-sensing resistors (FSRs) simultaneously. An experimental study was carried out with 25 healthy subjects (right-handed). The results showed that the mean flexion angles of the finger joints required to perform the 16 activities were Thumb (Carpometacarpal Joint (CMC) 28.56°, Metacarpophalangeal Joint (MCP) 26.84°, and Interphalangeal Joint (IP) 13.23°), Index (MCP 46.18°, Index Proximal Interphalangeal Joint (PIP) 38.89°), Middle (MCP 47.5°, PIP 42.62°), Ring (MCP 44.09°, PIP 39.22°), and Little (MCP 31.50°, PIP 22.10°). The averaged fingertip force exerted in the Grasp Subscale was 8.2 N, in Grip subscale 6.61 N and Pinch subscale 3.89 N. These results suggest that the integration of multiple sensors during the performance of the ARAT has clinical relevance, allowing therapists and other health professionals to perform a more sensitive, objective, and quantitative assessment of the hand function.

Development of a revolute-type kinematic model for human upper limb using a matrix approach

A mathematical model is proposed for a revolute joint mechanism with an n-degree of freedom (DOF). The matrix approach is used for finding the relation between two consecutive links to determine desired link parameters such as position, velocity and acceleration using the forward kinematic approach. The matrix approach was confirmed for a proposed 10 DOF revolute type (R-type) human upper limb model with servo motors at each joint. Two DOFs are considered each at shoulder, elbow and wrist joint, followed by four DOF for the fingers. Two DOFs were considered for metacarpophalangeal (mcp) and one DOF each for proximal interphalangeal (pip) and distal interphalangeal (dip) joints. MATLAB script function was used to evaluate the mathematical model for determining kinematic parameters for all the proposed human upper limb model joints. The simplified method for kinematic analysis proposed in this paper will further simplify the dynamic modeling of any mechanism for determining joint torques and hence, easy to design control system for joint movements.

Geometry-based finger kinematic models for joint rotation configuration and parameter estimation

In this work, geometry-based finger kinematic models for joint rotation configuration are proposed. The purpose of the work is to provide an effective means of describing an individual-specific finger motion during flexion or extension movements as precisely as possible. Based on the finger’s geometric postures that are observed when fingers naturally grasp a cylindrical object with a circular cross-section, its geometric relation between each phalanx of a finger and the object is extracted, and forms of contact between them are taken into consideration to secure more degrees of freedom for representing finger motions and are parameterized in the model development. A parameter identification approach is adopted to find model parameters that can be used to describe an individual-specific grasping style. For the validation of the proposed models, a set of optical motion capture experiments is performed. From the simulation study, one can see that the models provide one of the feasible and viable solutions to imitate the human finger’s flexion and/or extension movements.

Artificial-Hand Technology—Current State of Knowledge in Designing and Forecasting Changes

The subject of human-hand versatility has been intensively investigated for many years. Emerging robotic constructions change continuously in order to mimic natural mechanisms as accurately as possible. Such an attitude is motivated by the demand for humanoid robots with sophisticated end effectors and highly biomimic prostheses. This paper provides wide analysis of more than 80 devices that have been created over the last 40 years. It compares both the mechanical structure and various actuators from conventional DC motors and servomechanisms, through pneumatic muscles, to soft actuators and artificial muscles. Described measured factors include angles, forces, torques, tensions, and tactiles. Furthermore, the appropriate statistics of kinematic configuration, as well as the type or number of drive units and sensory systems, show not only recent problems, but also trends that will be followed in the future.

Sub-millimetre accurate human hand kinematics: from surface to skeleton

A highly accurate human hand kinematics model and identification are proposed. The model includes the five digits and the palm arc based on mapping function between surface landmarks and estimated joint centres of rotation. Model identification was experimentally performed using a motion tracking system. The evaluation of the marker position estimation error, which is on sub-millimetre level across all digits, underlines model quality and accuracy. Noticeably, with the development of this model, we were able to improve various modelling assumptions from literature and found a basic linear relationship between surface and skeleton rotational angles.

Interdependency of the maximum range of flexion-extension of hand metacarpophalangeal joints

Mobility of the fingers metacarpophalangeal (MCP) joints depends on the posture of the adjacent ones. Current Biomechanical hand models consider fixed ranges of movement at joints, regardless of the posture, thus allowing for non-realistic postures, generating wrong results in reach studies and forward dynamic analyses. This study provides data for more realistic hand models. The maximum voluntary extension (MVE) and flexion (MVF) of different combinations of MCP joints were measured covering their range of motion. Dependency of the MVF and MVE on the posture of the adjacent MCP joints was confirmed and mathematical models obtained through regression analyses (RMSE 7.7°).