Fluid-structure interactions in micro-interlocked regions of the cement-bone interface

Mechanical loading intensities affect the release of extracellular vesicles from mouse bone marrow-derived hematopoietic progenitor cells and change their osteoclast-modulating effect

Low-intensity loading maintains or increases bone mass, whereas lack of mechanical loading and high-intensity loading decreases bone mass, possibly via the release of extracellular vesicles by mechanosensitive bone cells. How different loading intensities alter the biological effect of these vesicles is not fully understood. Dynamic fluid shear stress at low intensity (0.7 ± 0.3 Pa, 5 Hz) or high intensity (2.9 ± 0.2 Pa, 1 Hz) was used on mouse hematopoietic progenitor cells for 2 min in the presence or absence of chemical compounds that inhibit release or biogenesis of extracellular vesicles. We used a Receptor activator of nuclear factor kappa-Β ligand-induced osteoclastogenesis assay to evaluate the biological effect of different fractions of extracellular vesicles obtained through centrifugation of medium from hematopoietic stem cells. Osteoclast formation was reduced by microvesicles (10 000× g) obtained after low-intensity loading and induced by exosomes (100 000× g) obtained after high-intensity loading. These osteoclast-modulating effects could be diminished or eliminated by depletion of extracellular vesicles from the conditioned medium, inhibition of general extracellular vesicle release, inhibition of microvesicle biogenesis (low intensity), inhibition of ESCRT-independent exosome biogenesis (high intensity), as well as by inhibition of dynamin-dependent vesicle uptake in osteoclast progenitor cells. Taken together, the intensity of mechanical loading affects the release of extracellular vesicles and change their osteoclast-modulating effect.

Roles of inflammatory cell infiltrate in periprosthetic osteolysis

Classically, particle-induced periprosthetic osteolysis at the implant-bone interface has explained the aseptic loosening of joint replacement. This response is preceded by triggering both the innate and acquired immune response with subsequent activation of osteoclasts, the bone-resorbing cells. Although particle-induced periprosthetic osteolysis has been considered a foreign body chronic inflammation mediated by myelomonocytic-derived cells, current reports describe wide heterogeneous inflammatory cells infiltrating the periprosthetic tissues. This review aims to discuss the role of those non-myelomonocytic cells in periprosthetic tissues exposed to wear particles by showing original data. Specifically, we discuss the role of T cells (CD3+, CD4+, and CD8+) and B cells (CD20+) coexisting with CD68+/TRAP- multinucleated giant cells associated with both polyethylene and metallic particles infiltrating retrieved periprosthetic membranes. This review contributes valuable insight to support the complex cell and molecular mechanisms behind the aseptic loosening theories of orthopedic implants.

The release of osteoclast-stimulating factors on supraphysiological loading by osteoprogenitors coincides with expression of genes associated with inflammation and cytoskeletal arrangement

Supraphysiological loading induced by unstable orthopedic implants initiates osteoclast formation, which results in bone degradation. We aimed to investigate which mechanosensitive cells in the peri-implant environment produce osteoclast-stimulating factors and how the production of these factors is stimulated by supraphysiological loading. The release of osteoclast-stimulating factors by different types of isolated bone marrow-derived hematopoietic and mesenchymal stem cells from six osteoarthritic patients was analyzed after one hour of supraphysiological loading (3.0 ± 0.2 Pa, 1 Hz) by adding their conditioned medium to osteoclast precursors. Monocytes produced factors that enhanced osteoclastogenesis by 1.6 ± 0.07-fold and mesenchymal stem cells by 1.4 ± 0.07-fold. Medium from osteoprogenitors and pre-osteoblasts enhanced osteoclastogenesis by 1.3 ± 0.09-fold and 1.4 ± 0.03-fold, respectively, where medium from four patients elicited a response and two did not. Next generation sequencing analysis of osteoprogenitors revealed that genes encoding for inflammation-related pathways and cytoskeletal rearrangements were regulated differently between responders and non-responders. Our data suggest that released osteoclast-stimulating soluble factors by progenitor cells in the bone marrow after supraphysiological loading may be related to cytoskeletal arrangement in an inflammatory environment. This connection could be relevant to better understand the aseptic loosening process of orthopedic implants.

Progressive loss of implant fixation in a preclinical rat model of cemented knee arthroplasty

Aseptic loosening of total knee arthroplasty continues to be a challenging clinical problem. The progression of the loosening process, from the initial well-fixed component, is not fully understood. In this study, loss of fixation of cemented hemiarthroplasty was explored using 9-month-old Sprague-Dawley rats with 0, 2, 6, 12, 26 week end points. Morphological and cellular changes of cement-bone fixation were determined for regions directly below the tibial tray (epiphysis) and distal to the tray (metaphysis). Loss of fixation, with a progressive increase in cement-bone gap volume was found in the epiphysis (0.162  mm³ /week), but did not progress appreciably in the metaphysis (0.007 mm³ /week). In the epiphysis, there was an early and sustained elevation of osteoclasts adjacent to the cement border and development of a fibrous tissue layer between the cement and bone. There was early formation of bone around the cement in the metaphysis, resulting in a condensed bone layer without osteoclastic bone resorption or development of a fibrous tissue layer. Implant positioning was also an important factor in the cement-bone gap formation, with greater gap formation for implants that were placed medially on the tibial articular surface. Loss of fixation in the rat model mimicked patterns found in human arthroplasty where cement-bone gaps initiate under the tibial tray, at the periphery of the implant. This preclinical model could be used to study early biological response to cemented fixation and associated contributions of mechanical instability, component alignment, and periprosthetic inflammation.

A Multiscale Finite Element Analysis of Balloon Kyphoplasty to Investigate the Risk of Bone-Cement Separation In Vivo

BACKGROUND

During the past decade there has been a significant increase in the number of vertebral fractures being treated with the balloon kyphoplasty procedure. Although previous investigations have found kyphoplasty to be an effective treatment for reducing patient pain and lowering cement-leakage risk, there have been reports of vertebral recollapse following the procedure. These reports have indicated evidence of in vivo bone-cement separation leading to collapse of the treated vertebra.

METHODS

The following study documents a multiscale analysis capable of evaluating the risk of bone-cement interface separation during lying, standing, and walking activities following balloon kyphoplasty.

RESULTS

Results from the analysis found that instances of reduced cement interlock could initiate both tensile and shear separation of the interface region at up to 7 times the failure threshold during walking or up to 1.9 times the threshold during some cases for standing. Lying prone offered the best protection from interface failure in all cases, with a minimum safety factor of 2.95.

CONCLUSIONS

The results of the multiscale analysis show it is essential for kyphoplasty simulations to take account of the micromechanical behavior of the bone-cement interface to be truly representative of the in vivo situation after the treatment. The results further illustrate the importance of ensuring adequate cement infiltration into the compacted bone periphery during kyphoplasty through a combination of new techniques, tools, and biomaterials in a multifaceted approach to solve this complex challenge.

Bioactive, Ion-Releasing PMMA Bone Cement Filled with Functional Graphenic Materials

Graphene oxide and functionalized graphenic materials (FGMs) have promise as platforms for imparting programmable bioactivity to poly(methyl methacrylate) (PMMA)-based bone cement. To date, however, graphenic fillers have only been feasible in PMMA cements at extremely low loadings, limiting the bioactive effects. At higher loadings, graphenic fillers decrease cement strength by aggregating and interfering with curing process. Here, these challenges are addressed by combining bioactive FGM fillers with a custom cement formulation. These cements contain an order of magnitude more graphenic filler than previous reports. Even at 1 wt% FGM, these cements have compressive strengths of 78- 88 MPa, flexural strengths of 74-81 MPa, and flexural stiffnesses of 1.8-1.9 GPa, surpassing the ASTM requirements for bone cement and competing with traditional PMMA cement. Further, by utilizing designer FGMs with programmed bioactivity, these cements demonstrate controlled release of osteogenic calcium ions (releasing a total of 5 ± 2 µmol of Ca2+ per gram of cement over 28 d) and stimulate a 290% increase in expression of alkaline phosphatase in human mesenchymal stem cells in vitro. Also, design criteria are described to guide creation of future generations of bone cements that utilize FGMs as platforms to achieve dynamic biological activity.

Similitude of cement-bone micromechanics in cemented rat and human knee replacement

A preclinical rat knee replacement model was recently developed to explore the biological and mechanobiological changes of trabecular resorption for cement-bone interdigitated regions. The goal here was to evaluate the relevance of this model compared with human knee replacement with regards to functional micromechanics. Eight nonsurvival, cemented knee replacement surgeries were performed, the interdigitated gap morphology was quantified, and interface micromotion between cement and bone was measured for 1 to 5 bodyweight loading. Computational fluid dynamics modeling of unit cell geometries with small gaps between trabeculae and cement was used to estimate fluid flow. Gap width (3.6 μm) was substantially smaller compared with cement-bone gaps reported in human knee replacement (11.8 μm). Micromotion at the cement-bone border was also decreased for the rat knee replacement (0.48 μm), compared with human (1.97 μm), for 1 bodyweight loading. However, the micromotion-to-gap width ratio (0.19 and 0.22 for, rat and human), and estimated fluid shear stress (6.47 and 7.13 Pa, for rat and human) were similar. Replicating the fluid dynamic characteristics of cement-bone interdigitated regions in human knee replacements using preclinical models may be important to recapitulate trabecular resorption mechanisms due to proposed supraphysiologic fluid shear stress. Statement of clinical significance: local cement-bone micromotion due to joint loading may contribute to the process of clinical loosening in total joint replacements. This work shows that while micromotion and gap morphology are diminished for the rat knee model compared to human, the motion-to-gap ratio, and corresponding fluid shear stress are of similar magnitudes.

High shear stress amplitude in combination with prolonged stimulus duration determine induction of osteoclast formation by hematopoietic progenitor cells

To date, it is unclear how fluid dynamics stimulate mechanosensory cells to induce an osteoprotective or osteodestructive response. We investigated how murine hematopoietic progenitor cells respond to 2 minutes of dynamic fluid flow stimulation with a precisely controlled sequence of fluid shear stresses. The response was quantified by measuring extracellular adenosine triphosphate (ATP), immunocytochemistry of Piezo1, and sarcoplasmic/endoplasmic Ca²⁺ reticulum ATPase 2 (SERCA2), and by the ability of soluble factors produced by mechanically stimulated cells to modulate osteoclast differentiation. We rejected our initial hypothesis that peak wall shear stress rate determines the response of hematopoietic progenitor cells to dynamic fluid shear stress, as it had only a minor correlation with the abovementioned parameters. Low stimulus amplitudes corresponded to activation of Piezo1, SERCA2, low concentrations of extracellular ATP, and inhibition of osteoclastogenesis and resorption area, while high amplitudes generally corresponded to osteodestructive responses. At a given amplitude (3 Pa) and waveform (square), the duration of individual stimuli (duty cycle) showed a strong correlation with the release of ATP and osteoclast number and resorption area. Collectively, our data suggest that hematopoietic progenitor cells respond in a viscoelastic manner to loading, since a combination of high shear stress amplitude and prolonged duty cycle is needed to trigger an osteodestructive response. PLAIN LANGUAGE SUMMARY: In case of painful joints or missing teeth, the current intervention is to replace them with an implant to keep a high-quality lifestyle. When exercising or chewing, the cells in the bone around the implant experience mechanical loading. This loading generally supports bone formation to strengthen the bone and prevent breaking, but can also stimulate bone loss when the mechanical loading becomes too high around orthopedic and dental implants. We still do not fully understand how cells in the bone can distinguish between mechanical loading that strengthens or weakens the bone. We cultured cells derived from the bone marrow in the laboratory to test whether the bone loss response depends on (i) how fast a mechanical load is applied (rate), (ii) how intense the mechanical load is (amplitude), or (iii) how long each individual loading stimulus is applied (duration). We mimicked mechanical loading as it occurs in the body, by applying very precisely controlled flow of fluid over the cells. We found that a mechanosensitive receptor Piezo1 was activated by a low amplitude stimulus, which usually strengthens the bone. The potential inhibitor of Piezo1, namely SERCA2, was only activated by a low amplitude stimulus. This happened regardless of the rate of application. At a constant high amplitude, a longer duration of the stimulus enhanced the bone-weakening response. Based on these results we deduce that a high loading amplitude tends to be bone weakening, and the longer this high amplitude persists, the worse it is for the bone.

Mechanical instability induces osteoclast differentiation independent of the presence of a fibrous tissue interface and osteocyte apoptosis in a rat model for aseptic loosening

Background and purpose - Insufficient initial fixation or early micromotion of an implant is associated with a thin layer of fibrous tissue at the peri-implant interface. It is unknown if bone loss is induced by the fibrous tissue interface acting as an active biological membrane, or as a membrane that will produce supraphysiologic fluid flow conditions during gait, which activates the mechanosensitive osteocytes to mediate osteoclast differentiation. We investigated whether mechanically induced osteolysis is dependent on the fibrous tissue interface as a biologically active scaffold, or if it merely acts as a conduit for fluid flow, affecting the mechanosensitive osteocytes in the peri-prosthetic bone.Methods - Using a rat model of mechanically instability-induced aseptic loosening, we assessed whether the induction of osteoclast differentiation was dependent on the presence of a peri-implant fibrous interface. We analyzed the amount of osteoclast differentiation, osteocyte apoptosis, pro-resorptive cytokine expression and bone loss using immunohistochemistry, mRNA expression and micro-CT.Results - Osteoclast differentiation and bone loss were induced by mechanical instability but were not affected by the presence of the fibrous tissue membrane or associated with osteocyte apoptosis. There was no increased mRNA expression of any of the cytokines in the fibrous tissue membrane compared with the peri-implant bone.Interpretation - Our data show that the fibrous tissue membrane in the interface plays a minor role in inducing bone loss. This indicates that the peri-implant bone adjacent to loose bone implants might play an important role for osteoclast differentiation.

Early Changes in Cement-Bone Fixation Using a Novel Rat Knee Replacement Model

Trabecular resorption from interdigitated regions between cement and bone has been found in postmortem-retrieved knee replacements, but the viability of interdigitated bone, and the mechanism responsible for this bone loss is not known. In this work, a Sprague-Dawley (age 12 weeks) rat knee replacement model with an interdigitated cement-bone interface was developed. Morphological and cellular changes in the interdigitated region of the knee replacement over time (0, 2, 6, or 12 weeks) were determined for ovariectomy (OVX) and Sham OVX treatment groups. Interdigitated bone volume fraction (BV/TV) increased with time for Sham OVX (0.022 BV/TV/wk) and OVX (0.015 BV/TV/wk) group, but the rate of increase was greater for the Sham OVX group (p = 0.0064). Tissue mineral density followed a similar increase with time in the interdigitated regions. Trabecular resorption, when it did occur, started at the cement border with medullary-adjacent bone in the presence of osteoclasts. There was substantial loss of viable bone (~80% empty osteocyte lacunae) in the interdigitated regions. Pre-surgical fluorochrome labels remained in the interdigitated regions, and did not diminish with time, indicating that the bone was not remodeling. There was also some evidence of continued surface mineralization in the interdigitated region after cementing of the knee, but this diminished over time. Statement of clinical significance: Interdigitated bone with cement provides mechanical stability for success of knee replacements. Improved understanding of the fate of the interdigitated bone over time could lead to a better understanding of the loosening process and interventions to prevent loss of fixation. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:2163-2171, 2019.

Mechanically Induced Periprosthetic Osteolysis: A Systematic Review

BACKGROUND

Peri-prosthetic bone loss can result from chemical, biological, and mechanical factors. Mechanical stimulation via fluid pressure and flow at the bone-implant interface may be a significant cause. Evidence supporting mechanically induced osteolysis continues to grow, but there is no synthesis of published clinical and basic science data.

QUESTIONS/PURPOSES

We sought to review the literature on two questions: (1) What published evidence supports the concept of mechanically induced osteolysis? (2) What is the proposed mechanism of mechanically induced osteolysis, and does it differ from that of particle-induced osteolysis?

METHODS

A systematic review was performed of the PubMed and Web of Science databases. Additional relevant articles were recommended by the senior authors based on their expert opinion. Abstracts were reviewed and the manuscripts pertaining to the study questions were read in full. Studies showing support of mechanically induced osteolysis were quantified and findings summarized.

RESULTS

We identified 49 articles of experimental design supporting the hypothesis that mechanical stimulation of peri-prosthetic bone from fluid pressure and flow can induce osteolysis. While the molecular mechanisms may overlap with those implicated in particle-induced osteolysis, mechanically induced osteolysis appears to be mediated by distinct and parallel pathways.

CONCLUSIONS

The role of mechanical stimuli is increasingly recognized in the pathogenesis of peri-prosthetic osteolysis. Current research aims to elucidate the molecular mechanisms to better target therapeutic interventions.

FEM-Based Compression Fracture Risk Assessment in Osteoporotic Lumbar Vertebra L1

This paper presents a finite element method (FEM)-based fracture risk assessment in patient-specific osteoporotic lumbar vertebra L1. The influence of osteoporosis is defined by variation of parameters such as thickness of the cortical shell, the bone volume–total volume ratio (BV/TV), and the trabecular bone score (TBS). The mechanical behaviour of bone is defined using the Ramberg–Osgood material model. This study involves the static and nonlinear dynamic calculations of von Mises stresses and follows statistical processing of the obtained results in order to develop the patient-specific vertebra reliability. In addition, different scenarios of parameters show that the reliability of the proposed model of human vertebra highly decreases with low levels of BV/TV and is critical due to the thinner cortical bone, suggesting high trauma risk by reason of osteoporosis.

Mechanical loading releases osteoclastogenesis-modulating factors through stimulation of the P2X7 receptor in hematopoietic progenitor cells

Mechanical instability of bone implants stimulate osteoclast differentiation and peri-implant bone loss, leading to prosthetic loosening. It is unclear which cells at the periprosthetic interface transduce mechanical signals into a biochemical response, and subsequently facilitate bone loss. We hypothesized that mechanical overloading of hematopoietic bone marrow progenitor cells, which are located near to the inserted bone implants, stimulates the release of osteoclast-inducing soluble factors. Using a novel in vitro model to apply mechanical overloading, we found that hematopoietic progenitor cells released adenosine triphosphate (ATP) after only 2 min of mechanical loading. The released ATP interacts with its specific receptor P2X7 to stimulate the release of unknown soluble factors that inhibit (physiological loading) or promote (supraphysiological loading) the differentiation of multinucleated osteoclasts derived from bone marrow cultures. Inhibition of ATP-receptor P2X7 by Brilliant Blue G completely abolished the overloading-induced stimulation of osteoclast formation. Likewise, stimulation of P2X7 receptor on hematopoietic cells by BzATP enhanced the release of osteoclastogenesis-stimulating signaling molecules to a similar extent as supraphysiological loading. Supraphysiological loading affected neither gene expression of inflammatory markers involved in aseptic implant loosening (e.g., interleukin-1β (IL-1β), IL-6, tumor necrosis factor-α, and PTGES2) nor expression of the osteoclast modulators receptor activator of nuclear factor κ-Β ligand and osteoprotegerin. Our findings suggest that murine hematopoietic progenitor cells are a potential key player in local mechanical loading-induced bone implant loosening via the ATP/P2X7-axis. Our approach identifies potential therapeutic targets to prevent prosthetic loosening.

Supraphysiological loading induces osteocyte-mediated osteoclastogenesis in a novel in vitro model for bone implant loosening

We aimed to develop an in vitro model for bone implant loosening, allowing analysis of biophysical and biological parameters contributing to mechanical instability-induced osteoclast differentiation and peri-implant bone loss. MLO-Y4-osteocytes were mechanically stimulated for 1 h by fluid shear stress using regimes simulating: (i) supraphysiological loading in the peri-prosthetic interface (2.9 ± 2.9 Pa, 1 Hz, square wave); (ii) physiologic loading in the cortical bone (0.7 ± 0.7 Pa, 5 Hz, sinusoidal wave); and (iii) stress shielding. Cellular morphological parameters, membrane-bound RANKL expression, gene expression influencing osteoclast differentiation, nitric oxide release and caspase 3/7-activity were determined. Either Mouse bone marrow cells were cultured on top of loaded osteocytes or osteocyte-conditioned medium was added to bone marrow cells. Osteoclast differentiation was assessed after 6 days. We found that osteocytes subjected to supraphysiological loading showed similar morphology and caspase 3/7-activity compared to simulated physiological loading or stress shielding. Supraphysiological stimulation of osteocytes enhanced osteoclast differentiation by 1.9-fold compared to physiological loading when cell-to-cell contact was permitted. In addition, it enhanced the number of osteoclasts using conditioned medium by 1.7-fold, membrane-bound RANKL by 3.3-fold, and nitric oxide production by 3.2-fold. The stimulatory effect of supraphysiological loading on membrane-bound RANKL and nitric oxide production was higher than that achieved by stress shielding. In conclusion, the in vitro model developed recapitulated the catabolic biological situation in the peri-prosthetic interface during instability that is associated with osteoclast differentiation and enhanced RANKL expression. The model thus provides a platform for pre-clinical testing of pharmacological interventions with potential to stop instability-induced bone implant loosening. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1425-1434, 2018.

Trabecular resorption patterns of cement-bone interlock regions in total knee replacements

With in vivo service, there is loss of mechanical interlock between trabeculae and PMMA cement in total knee replacements. The mechanisms responsible for the loss of interlock are not known, but loss of interlock results in weaker cement-bone interfaces. The goal of this study was to determine the pattern of resorption of interdigitated bone using a series of 20 postmortem retrieved knee replacements with a wide range of time in service (3-22 years). MicroCT scans were obtained of a segment of the cement-bone interface below the tibial tray for each implant. Image processing methods were used to determine interface morphology and to identify supporting, interdigitated, resorbed, and isolated bone as a function of axial position. Overall, the amount of remaining interdigitated bone decreased with time in service (p = 0.0114). The distance from the cement border (at the extent of cement penetration into the bone bed) to 50% of the interdigitated volume decreased with time in service (p = 0.039). Isolated bone, when present, was located deep in the cement layer. Overall, resorption appears to start at the cement border and progresses into the cement layer. Initiation of trabecular resorption near the cement border may be a consequence of proximity to osteoclastic cells in the adjacent marrow space.

CLINICAL SIGNIFICANCE

Aseptic loosening of joint replacements remains an important clinical problem. This work explores the process and pattern of trabecular bone resorption responsible for loss of interface fixation. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:2773-2780, 2017.

GSK-3β inhibition suppresses instability-induced osteolysis by a dual action on osteoblast and osteoclast differentiation

Currently, there are no medications available to treat aseptic loosening of orthopedic implants. Using osteoprotegerin fusion protein (OPG-Fc), we previously blocked instability-induced osteoclast differentiation and peri-prosthetic osteolysis. Wnt/β-catenin signaling, which regulates OPG secretion from osteoblasts, also modulates the bone tissue response to mechanical loading. We hypothesized that activating Wnt/β-catenin signaling by inhibiting glycogen synthase kinase-3β (GSK-3β) would reduce instability-induced bone loss through regulation of both osteoblast and osteoclast differentiation. We examined effects of GSK-3β inhibition on regulation of RANKL and OPG in a rat model of mechanical instability-induced peri-implant osteolysis. The rats were treated daily with a GSK-3β inhibitor, AR28 (20 mg/kg bw), for up to 5 days. Bone tissue and blood serum were assessed by qRT-PCR, immunohistochemistry, and ELISA on days 3 and 5, and by micro-CT on day 5. After 3 days of treatment with AR28, mRNA levels of β-catenin, Runx2, Osterix, Col1α1, and ALP were increased leading to higher osteoblast numbers compared to vehicle-treated animals. BMP-2 and Wnt16 mRNA levels were downregulated by mechanical instability and this was rescued by GSK-3β inhibition. Osteoclast numbers were decreased significantly after 3 days of GSK-3β inhibition, which correlated with enhanced OPG mRNA expression. This was accompanied by decreased serum levels of TRAP5b on days 3 and 5. Treatment with AR28 upregulated osteoblast differentiation, while osteoclastogenesis was blunted, leading to increased bone mass by day 5. These data suggest that GSK-3β inactivation suppresses osteolysis through regulating both osteoblast and osteoclast differentiation in a rat model of instability-induced osteolysis.

[Endoprostheses in the elderly : Biomaterials, implant selection and fixation technique]

The replacement of hip and knee joints is one of the greatest success stories in orthopedics. Due to continuous improvement of biomaterials and implant design, patient-associated problems are now mostly multifactorial and only rarely caused by the implant. Abrasion was significantly reduced by the introduction of highly cross-linked polyethylene (PE), antioxidant stabilized PE, new ceramics and the development of ceramic and protective surfaces. It is assumed that further reduction of frictional resistance will not lead to a significantly better clinical result: however, the problem of periprosthetic infections and implant-related incompatibility is still unsolved and remains challenging for biomaterial research. For the knee joint PE will be irreplaceable for joint articulation even in the future due to the contact situation. Mobile bearings and fixed bearings are two established successful philosophies, which have shown comparably good clinical results. For the hip joint, it is forecasted that ceramic-on-ceramic will be the system of the future if the correct positioning and mounting of the components can be solved so that the problems, such as development of noise and breakage can be reduced to a minimum. An in-depth understanding and detailed knowledge of the biomaterials by the surgeon can prevent implant-related problems. For elderly patients it is assumed that the economic burden on the public healthcare system will have the strongest impact on implant selection.

Micromotion-induced peri-prosthetic fluid flow around a cementless femoral stem

Micromotion-induced interstitial fluid flow at the bone-implant interface has been proposed to play an important role in aseptic loosening of cementless implants. High fluid velocities are thought to promote aseptic loosening through activation of osteoclasts, shear stress induced control of mesenchymal stem cells differentiation, or transport of molecules. In this study, our objectives were to characterize and quantify micromotion-induced fluid flow around a cementless femoral stem using finite element modeling. With a 2D model of the bone-implant interface and full-factorial design, we first evaluated the relative influence of material properties, and bone-implant micromotion and gap on fluid velocity. Transverse sections around a femoral stem were built from computed tomography images, while boundary conditions were obtained from experimental measurements on the same femur. In a second step, a 3D model was built from the same data-set to estimate the shear stress experienced by cells hosted in the peri-implant tissues. The full-factorial design analysis showed that local micromotion had the most influence on peak fluid velocity at the interface. Remarkable variations in fluid velocity were observed in the macrostructures at the surface of the implant in the 2D transverse sections of the stem. The 3D model predicted peak fluid velocities extending up to 2.2 mm/s in the granulation tissue and to 3.9 mm/s in the trabecular bone. Peak shear stresses on the cells hosted in these tissues ranged from 0.1 to 12.5 Pa. These results offer insight into mechanical stimuli encountered at the bone-implant interface.

Strain shielding in trabecular bone at the tibial cement-bone interface

Aseptic loosening of the tibial component remains the leading cause for revision surgery in total knee arthroplasty (TKA). Understanding the mechanisms leading to loss of fixation can offer insight into preventative measures to ensure a longer survival rate. In cemented TKA, loosening occurs at the cement-trabecular interface probably due to a stress-shielding effect of the stiffer implant material in comparison with bone. Using finite element models of lab-prepared tibial cement-trabeculae interface specimens (n=4) based on micro-CT images, this study aims to investigate the micromechanics of the interlock between cement and trabecular bone. Finite element micromotion between cement and trabeculae and bone strain were compared in the interdigitated trabeculae as well as strain in the bone distal to the interface. Lab-prepared specimens and their FE models were assumed to represent the immediate post-operative situation. The cement layer was removed in the FE models while retaining the loading conditions, which resulted in FE models that represented the pre-operative situation. Results showed that micromotion and bone strain decrease when interdigitation depth increases. Bone-cement micromotion and bone strain at the distal interdigitated region showed a dependence on bone volume fraction. Comparing the immediate post-operative and pre-operative situations, trabeculae embedded deep within the cement generally showed the highest level of strain-shielding. Strain shielding of interdigitated bone, in terms of reduction in compressive strains, was found to be between 35 and 61 % for the four specimens. Strain adaptive remodeling could thus be a plausible mechanism responsible for loss of interdigitated bone.

Changes in microgaps, micromotion, and trabecular strain from interlocked cement-trabecular bone interfaces in total knee replacements with in vivo service

The initial fixation of cemented Total Knee Replacements (TKRs) relies on mechanical interlock between cement and bone, but loss of interlock occurs with in vivo service. In this study, cement-trabeculae gap morphology and micromechanics were measured for lab prepared (representing post-operative state) and postmortem retrieval (with in vivo remodeling) TKRs to determine how changes in fixation affect local micromechanics. Small specimens taken from beneath the tibial tray were loaded with 1 MPa axial compression and the local micromechanics of the trabeculae-cement interface was quantified using digital image correlation. Lab prepared trabeculae that initially interlock with cement had small gaps (ave:14 μm) and limited micromotion (ave:1 μm) which were larger near the cement border. Trabecular resorption was prevalent following in vivo service; interface gaps became larger (ave:40 μm) and micromotion increased (ave:6 μm), particularly near the cement border. Interlocked trabeculae from lab prepared specimens exhibited strains that were 20% of the supporting bone strain, indicating the trabeculae were initially strain shielded. The spatial and temporal progression of gaps, micromotion, and bone strain was complex and much more variable for post-mortem retrievals compared to the lab prepared specimens. From a clinical perspective, attaining more initial interlock results in cement-bone interfaces that are better fixed with less micromotion. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:1019-1025, 2016.

Experimental and computational micromechanics at the tibial cement-trabeculae interface

Aseptic loosening of the tibial component in cemented total knee arthroplasty remains a major concern. We hypothesize that micromotion between the cement and trabeculae leads to increased circulation of interstitial fluid which in turn causes fluid-induced resorption of the trabeculae. Another mechanism for implant loosening is trabecular strain shielding. Using a newly developed experimental setup and digital image correlation (DIC) methods we were able to measure micromotion and strains in lab-prepared cement-trabeculae interface specimens (n=4). Finite element (FE) models of these specimens were developed to determine whether differences in micromotion and strain in morphologically varying specimens could be simulated accurately. Results showed that the measured micromotion and strains correlated well with FE model predictions (r(2)=0.59-0.85; r(2)=0.66-0.90). Global specimen strains measured axially matched well with the FE model strains (r(2)=0.87). FE model cement strains showed an increasing trend with distance from the cement border. The influence of loss of trabecular connectivity at the specimen edges was studied using our FE model results. Micromotion values at the outer edge of the specimens were higher than the specimen interior when considering a very thin outer edge (0.1mm). When the outer edge thickness was increased to about one trabecular length (0.8mm), there was a drop in the median and peak values. Using the experimental and modelling approach outlined in this study, we can further study the mechanisms that lead to loss of interlock between cement and trabeculae at the tibial interface.

In vivo loss of cement-bone interlock reduces fixation strength in total knee arthroplasties

Prevention of aseptic loosening of total knee arthroplasties (TKAs) remains a clinical challenge. Understanding how changes in morphology at the implant-bone interface with in vivo service affect implant stability and strength could lead to new approaches to mitigate loosening. Enbloc TKA retrievals and freshly-cemented TKA tibial components were used to determine if the mechanical strength of the interface depended on the amount of cement-bone interlock and the morphology of the supporting bone under the cement layer. Implants were sectioned into small specimens of the cement-interface-bone from under the tibial tray. Micro-CT scans were used to document interlock morphology and architecture of the supporting trabecular bone. Axial compression tests were used to assess mechanical behavior. Postmortem retrievals had lower contact fraction (42 ± 55%) compared to freshly-cemented constructs (121 ± 61%) (p = 0.0008). Supporting bone architecture parameters were not different for the two groups. Increased interface contact fraction and supporting bone volume fraction (BV/TV) were positive predictors of interface strength (r(2)  = 0.72, p = 0.0001). For the same supporting bone BV/TV, postmortem specimens had weaker interfaces; they were also more compliant. Cemented TKAs with in vivo service experience a loss of fixation strength and increased micro-motion due to the loss of cement-bone interlock.

Loss of cement-bone interlock in retrieved tibial components from total knee arthroplasties

BACKGROUND

Aseptic loosening continues to be a short- and long-term complication for patients with cemented TKAs. Most studies to this point have evaluated tibial component fixation via radiographic changes at the implant-bone interface and quantification of component migration; direct assessment of morphologic features of the interface from functioning TKAs may provide new information regarding how TKAs function and are fixed to bone.

QUESTIONS/PURPOSES

In a postmortem retrieval study, we asked: (1) What are the morphologic features at the cement-trabecular bone interface in retrieved tibial components? (2) Do constructs with greater time in service have less cement-trabecular bone interlock? (3) Do constructs with more estimated initial interlock sustain more interlock with in vivo service?

METHODS

Fourteen postmortem retrieved tibial components with time in service from 0 to 20 years were sectioned and imaged at high resolution, and the current contact fraction, estimated initial interdigitation depth, current interdigitation depth, and loss of interdigitation depth were quantified at the cement-bone interface. Estimated initial interdigitation depth was calculated from the initial mold shape of the cement mantle that forms around the individual trabeculae at the time of surgery. Loss of interdigitation depth was the difference between the initial and current interdigitation depth.

RESULTS

There was resorption of trabeculae that initially interlocked with the cement in the postmortem retrievals as evidenced by the differences between current interdigitation and the estimated original interdigitation. The current contact fraction (r(2) = 0.54; p = 0.0027) and current interdigitation depth (r(2) = 0.33; p = 0.033) were less for constructs with longer time in service. The current contact fraction for implants with 10 or more years in service (6.2%; 95% CI, 4.7%-7.7%) was much less than implants with less than 10 years in service (22.9%; 95% CI, 8.9%-37%). Similarly, the current interdigitation depth for implants with 10 or more years in service (0.4 mm; 95% CI, 0.27-0.53 mm) was much less than implants with less than 10 years in service (1.13 mm; 95% CI, 0.48-1.78 mm). The loss of interdigitation depth had a strong positive relationship with time in service (r(2) = 0.74; p < 0.001). Using a two-parameter regression model, constructs with more initial interdigitation depth had greater current interdigitation depth (p = 0.011), but constructs with more time in service also had less current interdigitation depth (p = 0.008).

CONCLUSIONS

The cement-trabecular bone interlock obtained initially appears to diminish with time with in vivo service by resorption of the trabeculae in the cement interlock region.

CLINICAL RELEVANCE

Our study supports the surgical concept of obtaining sufficient initial cement interlock (approximately 3 mm), with the acknowledgment that there will be loss of interlock with time with in vivo service.

A novel in vitro loading system to produce supraphysiologic oscillatory fluid shear stress

A multi-well fluid loading (MFL) system was developed to deliver oscillatory subphysiologic to supraphysiologic fluid shear stresses to cell monolayers in vitro using standard multi-well culture plates. Computational fluid dynamics modeling with fluid-structure interactions was used to quantify the squeeze film fluid flow between an axially displaced piston and the well plate surface. Adjusting the cone angle of the piston base modulated the fluid pressure, velocity, and shear stress magnitudes. Modeling results showed that there was near uniform fluid shear stress across the well with a linear drop in pressure across the radius of the well. Using the MFL system, RAW 264.7 osteoclastic cells were exposed to oscillatory fluid shear stresses of 0, 0.5, 1.5, 4, 6, and 17 Pa. Cells were loaded 1 h per day at 1 Hz for two days. Compared to sub-physiologic and physiologic levels, supraphysiologic oscillatory fluid shear induced upregulation of osteoclastic activity as measured by tartrate-resistant acid phosphatase activity and formation of mineral resorption pits. Cell number remained constant across all treatment groups.

Osteolysis around total knee arthroplasty: a review of pathogenetic mechanisms

Aseptic loosening and other wear-related complications are some of the most frequent late reasons for revision of total knee arthroplasty (TKA). Periprosthetic osteolysis (PPOL) pre-dates aseptic loosening in many cases, indicating the clinical significance of this pathogenic mechanism. A variety of implant-, surgery- and host-related factors have been delineated to explain the development of PPOL. These factors influence the development of PPOL because of changes in mechanical stresses within the vicinity of the prosthetic device, excessive wear of the polyethylene liner, and joint fluid pressure and flow acting on the peri-implant bone. The process of aseptic loosening is initially governed by factors such as implant/limb alignment, device fixation quality and muscle coordination/strength. Later, large numbers of wear particles detached from TKA trigger and perpetuate particle disease, as highlighted by progressive growth of inflammatory/granulomatous tissue around the joint cavity. An increased accumulation of osteoclasts at the bone-implant interface, impairment of osteoblast function, mechanical stresses and increased production of joint fluid contribute to bone resorption and subsequent loosening of the implant. In addition, hypersensitivity and adverse reactions to metal debris may contribute to aseptic TKA failure, but should be determined more precisely. Patient activity level appears to be the most important factor when the long-term development of PPOL is considered. Surgical technique, implant design and material factors are the most important preventative factors, because they influence both the generation of wear debris and excessive mechanical stresses. New generations of bearing surfaces and designs for TKA should carefully address these important issues in extensive preclinical studies. Currently, there is little evidence that PPOL can be prevented by pharmacological intervention.