Numerical investigation of mechanical effects caused by various fixation positions on a new radius intramedullary nail

Three‑dimensional finite element analysis: Anatomical splint fixation for Colles fractures

With the rapid development of digital research in clinical orthopedics, the efficacy and safety of splint fixation can be better evaluated through biomechanical analysis based on a three-dimensional (3D) finite element model. It is essential to address the current gap in understanding the biomechanical implications of anatomical splint fixation for Colles fractures. By employing advanced 3D finite element analysis, the present study aimed to provide a comprehensive evaluation, offering valuable insights that can contribute to enhancing the effectiveness of anatomical splint fixation in the clinical management of Colles fractures. The 3D finite element models of the forearm and hand were constructed using Mimics 15.0 according to data from computed tomography of a patient with a Colles fracture. After the validity of the model was verified, the corresponding material properties of the models were adjusted to simulate a Colles fracture. Subsequently, the reduction functions, such as radial inclination and ulnar deviation, of the simulated fracture were completed and the mechanical changes of the tissues surrounding the fracture were calculated. Anatomical splints were then placed on the surfaces of the 3D finite element models of Colles fractures at various positions to analyze the changes in the stress cloud diagram, such as for the soft tissue and anatomical splints. In the present study, the constructed 3D finite element models were accurate and valid. The maximum stress of the anatomical splints and soft tissues was 2.346 and 0.106 MPa in pronation, 1.780 and 0.069 MPa in median rotation and 3.045 and 0.057 MPa in supination, respectively. Splint stress reached the highest level in supination and soft tissue stress achieved the highest level in pronation. The peak of splint stress occurred during supination, which contrasts to the peak of soft tissue stress observed in pronation, suggesting splint fixation median rotation can effectively avoid compression of the local soft tissue.

Finite Element Modeling of the Human Wrist: A Review

Background  Understanding wrist biomechanics is important to appreciate and treat the wrist joint. Numerical methods, specifically, finite element method (FEM), have been used to overcome experimental methods' limitations. Due to the complexity of the wrist and difficulty in modeling, there is heterogeneity and lack of consistent methodology in the published studies, challenging our ability to incorporate information gleaned from the various studies. Questions/Purposes  This study summarizes the use of FEM to study the wrist in the last decade. Methods  We included studies published from 2012 to 2022 from databases: EBSCO, Research4Life, ScienceDirect, and Scopus. Twenty-two studies were included. Results  FEM used to study wrist in general, pathology, and treatment include diverse topics and are difficult to compare directly. Most studies evaluate normal wrist mechanics, all modeling the bones, with fewer studies including cartilage and ligamentous structures in the model. The dynamic effect of the tendons on wrist mechanics is rarely accounted for. Conclusion  Due to the complexity of wrist mechanics, the current literature remains incomplete. Considering published strategies and modeling techniques may aid in the development of more comprehensive and improved wrist model fidelity.

Parametric Finite Element Analysis of Intramedullary Nail Fixation of Proximal Femur Fractures

Proximal femur fracture fixation with intramedullary nailing relies on stability at the fracture site and integrity of the fixation construct to achieve union. The biomechanics that dictate fracture site stability and implant stress depend on fracture type as well as implant features such as nail length, nail diameter, presence of distal fixation screws, and material composition of the implant. When deciding how to fix a fracture, surgeons have choices in these implant-related design variables. This study models all combinations of a range of implant variables for nine standard AO/OTA proximal femur fractures using finite element analysis. Under simulated maximum load during gait, the maximum stress in the implant and screws as well as interfragmentary motions at the fracture site in the axial and shear directions were computed. The results were separated by fracture type to show the influence of each design variable on measured biomechanical outcomes. Filling the reamed canal with the largest fitting nail diameter reduced axial and shear interfragmentary motion for all fracture types. Nail length was less predictive of shear interfragmentary motion for most simulated fracture types than other construct variables. Furthermore, gapping at the fracture site predisposed the construct to higher implant stresses and larger interfragmentary motions. Clinical significance: Biomechanical outcomes from this computational study can aid in surgical decision-making for optimizing hip fracture fixation with IM nailing. © 2019 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:2358-2366, 2019.

The biomechanical analysis of three-dimensional distal radius fracture model with different fixed splints

BACKGROUND

The distal radius fracture is one of the common clinical fractures. At present, there are no reports regarding application of the finite element method in studying the mechanism of Colles fracture and the biomechanical behavior when using splint fixation.

OBJECTIVE

To explore the mechanism of Colles fracture and the biomechanical behavior when using different fixed splints.

METHODS

Based on the CT scanning images of forearm for a young female volunteer, by using model construction technology combined with RPOE and ANSYS software, a 3-D distal radius fracture forearm finite element model with a real shape and bioactive materials is built. The material tests are performed to obtain the mechanical properties of the paper-based splint, the willow splint and the anatomical splint. The numerical results are compared with the experimental results to verify the correctness of the presented model. Based on the verified model, the stress distribution of different tissues are analyzed. Finally, the clinical tests are performed to observe and verify that the anatomical splint is the best fit for human body.

RESULTS

Using the three kinds of splints, the transferred bone stress focus on the distal radius and ulna, which is helpful to maintain the stability of fracture. Also the stress is accumulated in the distal radius which may be attributed to flexion position. Such stress distribution may be helpful to maintain the ulnar declination. By comparing the simulation results with the experimental observations, the anatomical splint has the best fitting to the limb, which can effectively avoid the local compression.

CONCLUSION

The anatomical splint is the most effective for fixing and curing the fracture. The presented model can provide theoretical basis and technical guide for further investigating mechanism of distal radius fracture and clinical application of anatomical splint.

Biomechanical investigation of titanium elastic nail prebending for treating diaphyseal long bone fractures

This study numerically investigated the deformation of titanium elastic nails prebent at various degrees during implantation into the intramedullary canal of fractured bones and the mechanism by which this prebending influenced the stability of the fractured bone. Three degrees of prebending the implanted portions of the nails were used: equal to, two times, and three times the diameter of the intramedullary canal. Furthermore, a simulated diaphyseal fracture with a 5-mm gap was created in the middle shaft portion of the bone fixed with two elastic nails in a double C-type configuration. End caps were simulated using a constraint equation. To confirm that the simulation process is able to present the mechanical response of the nail inside the intramedullary, an experiment was conducted by using sawbone for validation. The results indicated that increasing the degrees of nail prebending facilitated straightening the nails against the inner aspect of canal after implantation, with increase in stability under torsion. Furthermore, reducing nail prebending caused a larger portion of the nails to move closer to the loading site and center of bone after implantation; the use of end caps prevented the nail tips from collapsing and increased axial stability. End cap use was critical for preventing the nail tips from collapsing and for increasing the stability of the nails prebent at a degree equal to the diameter of the canal with insufficient frictional force between the nail and canal. Therefore, titanium elastic nail prebending in a double C-type configuration with a degree three times the diameter of the canal represents a superior solution for treating transverse fractures without a gap, whereas that with a degree equal to the diameter of the intramedullary canal and combined with end cap use represents an advanced solution for treating comminuted fractures in a diaphyseal long bone fracture.

Computational comparison of tibial diaphyseal fractures fixed with various degrees of prebending of titanium elastic nails and with and without end caps

INTRODUCTION

Elastic stable intramedullary nailing (ESIN) is a treatment strategy for the management of diaphyseal long-bone fractures in adolescents and children, but few studies have investigated the mechanical stability of tibial diaphyseal fractures treated with various degrees of prebending of the elastic nails. Therefore, the aim of this study was to compare the mechanical stability, including the gap deformation and nail dropping, of a tibia fracture with various fracture sites and fixed with various degrees of prebending of the elastic nails by the finite element method. Furthermore, the contribution of end caps to stability was taken into consideration in the simulation.

METHODS

A tibia model was developed with a transverse fracture at the proximal, middle and distal parts of the diaphysis, and fixed with three degrees of prebending of elastic nails, including those equal to, two times and three times the diameter of the intramedullary canal. The outer diameter of the nail used in the computation was 3.5mm, and the fractured tibia was fixed with two elastic double C-type nails. Furthermore, the proximal end of each nail was set to free or being tied to the surrounding bone by a constraint equation to simulate with or without using end caps.

RESULTS

The results indicated that using end caps can prevent the fracture gap from collapsing by stopping the ends of the nails from dropping back in all prebending conditions and fracture patterns, and increasing the prebending of the nails to a degree three times the diameter of the canal reduced the gap shortening and the dropping distance of the nail end in those without using end caps under axial compression and bending. Insufficient prebending of the nails and not using end caps caused the gap to collapse and the nail to drop back at the entry point under loading.

CONCLUSIONS

Using end caps or increasing the prebending of the nails to three times the diameter of the canal is suggested to stop the nail from dropping back and thus produce a more stable structure, with less gap deformation, in the management of a simulated tibial diapyhseal fracture by using titanium elastic nails with a double C-shape.