Does handle shape influence prehensile capabilities and muscle coordination?

Force Control Strategy of Five-Digit Precision Grasping With Aligned and Unaligned Configurations

OBJECTIVE

To investigate the digit force control during a five-digit precision grasp in aligned (AG) and unaligned grasping (UG) configurations.

BACKGROUND

The effects of various cylindrical handles for tools on power grasp performance have been previously investigated. However, there is little information on force control strategy of precision grasp to fit various grasping configurations.

METHOD

Twenty healthy young adults were recruited to perform a lift-hold-lower task. The AG and UG configurations on a cylindrical simulator with force transducers were adjusted for each individual. The applied force and moment, the force variability during holding, and force correlations between thumb and each finger were measured.

RESULT

No differences in applied force, force correlation, repeatability, and variability were found between configurations. However, the moments applied in UG were significantly larger than those in AG.

CONCLUSION

The force control during precision grasp did not change significantly across AG and UG except for the digit moment. The simulator is controlled efficiently with large moment during UG, which is thus the optimal configuration for precision grasping with a cylindrical handle. Further research should consider the effects of task type and handle design on force control, especially for individuals with hand disorders.

APPLICATION

To design the handle of specific tool, one should consider the appropriate configuration according to the task requirements of precision grasping to reduce the risk of accumulating extra loads on digits with a cylindrical handle.

Development, fabrication and mechanical characterisation of auxetic bicycle handlebar grip

The auxetic cellular structures are one of the most promising metamaterials for vibration damping and crash absorption applications. Therefore, their use in the bicycle handlebar grip was studied in this work. A preliminary computational design study was performed using various auxetic and non-auxetic geometries under four load cases, which can typically appear. The most representative geometries were then selected and fabricated using additive manufacturing. These geometries were then experimentally tested to validate the discrete and homogenised computational models. The homogenised computational model was then used to analyse the biomechanical behaviour of the handlebar grip. It was observed that handle grip made from auxetic cellular metamaterials reduce the high contact pressures, provide similar stability and hereby improve the handlebar ergonomics.

Evaluation of the bio-dynamic response of the hand-arm system and hand-tool designs - A brief review

Hand-operated tools transmit a high magnitude of vibration exposure to the hand-arm system that causes occupational diseases. The health effects caused in various countries for the past years due to usage of hand tools are necessary to identify the occupational disorders. Researchers have conducted various studies on biological effects, hand-transmitted vibration exposure and biodynamic responses throughout the years. This article goes over each of these studies in detail, as well as identifying areas where more research is needed. The majority of studies deal with the following topics: general guidelines for hand-transmitted vibrations; assessment techniques of vibration exposure; hand-tool evaluation methods; influence of hand-tool design to overcome the biomechanical effects; and finite element modelling for quantifying vibration exposure. In response to this, understanding the biodynamic behaviour of the hand-arm system is useful for better ergonomic intervention in hand tools to reduce fatigue and increase comfort.

Real time relationship between individual finger force and grip exertion on distal phalanges in linear force following tasks

Individual finger force (FF) in a grip task is a vital concern in rehabilitation engineering and precise control of manipulators because disorders in any of the fingers will affect the stability or accuracy of the grip force (GF). To understand the functions of each finger in a dynamic grip exertion task, a GF following experiment with four individual fingers without thumb was designed. This study obtained four individual FFs from the distal phalanges with a cylindrical handle in dynamic GF following tasks. Ten healthy male subjects with similar hand sizes participated in the four-finger linear GF following tasks at different submaximal voluntary contraction (SMVC) levels. The total GF, individual FF, finger force contribution, and following error were subsequently calculated and analyzed. The statistics indicated the following: 1) the accuracy and stability of GF at low %MVC were significantly higher than those at high SMVC; 2) at low SMVC, the ability of the fingers to increase the GF was better than the ability to reduce it, but it was contrary at high SMVC; 3) when the target wave (TW) was changing, all four fingers strongly participated in the force exertion, but the participation of the little finger decreased significantly when TW remained stable; 4) the index finger and ring finger had a complementary relationship and played a vital role in the adjustment and control of GF. The middle finger and little finger had a minor influence on the force control and adjustment. In conclusion, each of the fingers had different functions in a GF following task. These findings can be used in the assessment of finger injury rehabilitation and for algorithms of precise control.

Using subject-specific three-dimensional (3D) anthropometry data in digital human modelling: case study in hand motion simulation

Digital human modelling enables ergonomists and designers to consider ergonomic concerns and design alternatives in a timely and cost-efficient manner in the early stages of design. However, the reliability of the simulation could be limited due to the percentile-based approach used in constructing the digital human model. To enhance the accuracy of the size and shape of the models, we proposed a framework to generate digital human models using three-dimensional (3D) anthropometric data. The 3D scan data from specific subjects' hands were segmented based on the estimated centres of rotation. The segments were then driven in forward kinematics to perform several functional postures. The constructed hand models were then verified, thereby validating the feasibility of the framework. The proposed framework helps generate accurate subject-specific digital human models, which can be utilised to guide product design and workspace arrangement. Practitioner Summary: Subject-specific digital human models can be constructed under the proposed framework based on three-dimensional (3D) anthropometry. This approach enables more reliable digital human simulation to guide product design and workspace arrangement.

Justification for a 2D versus 3D fingertip finite element model during static contact simulations

The biomechanical response of a human hand during contact with various products has not been investigated in details yet. It has been shown that excessive contact pressure on the soft tissue can result in discomfort, pain and also cumulative traumatic disorders. This manuscript explores the benefits and limitations of a simplified two-dimensional vs. an anatomically correct three-dimensional finite element model of a human fingertip. Most authors still use 2D FE fingertip models due to their simplicity and reduced computational costs. However we show that an anatomically correct 3D FE fingertip model can provide additional insight into the biomechanical behaviour. The use of 2D fingertip FE models is justified when observing peak contact pressure values as well as displacement during the contact for the given studied cross-section. On the other hand, an anatomically correct 3D FE fingertip model provides a contact pressure distribution, which reflects the fingertip's anatomy.