1
|
Fonseca L, Guiraud D, Hiairrassary A, Fattal C, Azevedo-Coste C. A Residual Movement Classification Based User Interface for Control of Assistive Devices by Persons with Complete Tetraplegia. IEEE Trans Neural Syst Rehabil Eng 2022; 30:569-578. [PMID: 35235517 DOI: 10.1109/tnsre.2022.3156269] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/09/2022]
Abstract
OBJECTIVE Complete tetraplegia can deprive a person of hand function. Assistive technologies may improve autonomy but needs for ergonomic interfaces for the user to pilot these devices still persist. Despite the paralysis of their arms, people with tetraplegia may retain residual shoulder movements. In this work we explored these movements as a mean to control assistive devices. METHODS We captured shoulder movement with a single inertial sensor and, by training a support vector machine based classifier, we decode such information into user intent. RESULTS The setup and training process take only a few minutes and so the classifiers can be user specific. We tested the algorithm with 10 able body and 2 spinal cord injury participants. The average classification accuracy was 80% and 84%, respectively. CONCLUSION The proposed algorithm is easy to set up, its operation is fully automated, and achieved results are on par with state-of-the-art systems. SIGNIFICANCE Assistive devices for persons without hand function present limitations in their user interfaces. Our work present a novel method to overcome some of these limitations by classifying user movement and decoding it into user intent, all with simple setup and training and no need for manual tuning. We demonstrate its feasibility with experiments with end users, including persons with complete tetraplegia without hand function.
Collapse
|
2
|
Gantenbein J, Dittli J, Meyer JT, Gassert R, Lambercy O. Intention Detection Strategies for Robotic Upper-Limb Orthoses: A Scoping Review Considering Usability, Daily Life Application, and User Evaluation. Front Neurorobot 2022; 16:815693. [PMID: 35264940 PMCID: PMC8900616 DOI: 10.3389/fnbot.2022.815693] [Citation(s) in RCA: 12] [Impact Index Per Article: 6.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/15/2021] [Accepted: 01/24/2022] [Indexed: 11/13/2022] Open
Abstract
Wearable robotic upper limb orthoses (ULO) are promising tools to assist or enhance the upper-limb function of their users. While the functionality of these devices has continuously increased, the robust and reliable detection of the user's intention to control the available degrees of freedom remains a major challenge and a barrier for acceptance. As the information interface between device and user, the intention detection strategy (IDS) has a crucial impact on the usability of the overall device. Yet, this aspect and the impact it has on the device usability is only rarely evaluated with respect to the context of use of ULO. A scoping literature review was conducted to identify non-invasive IDS applied to ULO that have been evaluated with human participants, with a specific focus on evaluation methods and findings related to functionality and usability and their appropriateness for specific contexts of use in daily life. A total of 93 studies were identified, describing 29 different IDS that are summarized and classified according to a four-level classification scheme. The predominant user input signal associated with the described IDS was electromyography (35.6%), followed by manual triggers such as buttons, touchscreens or joysticks (16.7%), as well as isometric force generated by residual movement in upper-limb segments (15.1%). We identify and discuss the strengths and weaknesses of IDS with respect to specific contexts of use and highlight a trade-off between performance and complexity in selecting an optimal IDS. Investigating evaluation practices to study the usability of IDS, the included studies revealed that, primarily, objective and quantitative usability attributes related to effectiveness or efficiency were assessed. Further, it underlined the lack of a systematic way to determine whether the usability of an IDS is sufficiently high to be appropriate for use in daily life applications. This work highlights the importance of a user- and application-specific selection and evaluation of non-invasive IDS for ULO. For technology developers in the field, it further provides recommendations on the selection process of IDS as well as to the design of corresponding evaluation protocols.
Collapse
Affiliation(s)
- Jessica Gantenbein
- Rehabilitation Engineering Laboratory, Department of Health Sciences and Technology, ETH Zurich, Zurich, Switzerland
| | - Jan Dittli
- Rehabilitation Engineering Laboratory, Department of Health Sciences and Technology, ETH Zurich, Zurich, Switzerland
| | - Jan Thomas Meyer
- Rehabilitation Engineering Laboratory, Department of Health Sciences and Technology, ETH Zurich, Zurich, Switzerland
| | - Roger Gassert
- Rehabilitation Engineering Laboratory, Department of Health Sciences and Technology, ETH Zurich, Zurich, Switzerland
- Future Health Technologies, Singapore-ETH Centre, Campus for Research Excellence and Technological Enterprise (CREATE), Singapore, Singapore
| | - Olivier Lambercy
- Rehabilitation Engineering Laboratory, Department of Health Sciences and Technology, ETH Zurich, Zurich, Switzerland
- Future Health Technologies, Singapore-ETH Centre, Campus for Research Excellence and Technological Enterprise (CREATE), Singapore, Singapore
| |
Collapse
|
3
|
Uwamahoro R, Sundaraj K, Subramaniam ID. Assessment of muscle activity using electrical stimulation and mechanomyography: a systematic review. Biomed Eng Online 2021; 20:1. [PMID: 33390158 PMCID: PMC7780389 DOI: 10.1186/s12938-020-00840-w] [Citation(s) in RCA: 11] [Impact Index Per Article: 3.7] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/13/2020] [Accepted: 12/11/2020] [Indexed: 11/10/2022] Open
Abstract
This research has proved that mechanomyographic (MMG) signals can be used for evaluating muscle performance. Stimulation of the lost physiological functions of a muscle using an electrical signal has been determined crucial in clinical and experimental settings in which voluntary contraction fails in stimulating specific muscles. Previous studies have already indicated that characterizing contractile properties of muscles using MMG through neuromuscular electrical stimulation (NMES) showed excellent reliability. Thus, this review highlights the use of MMG signals on evaluating skeletal muscles under electrical stimulation. In total, 336 original articles were identified from the Scopus and SpringerLink electronic databases using search keywords for studies published between 2000 and 2020, and their eligibility for inclusion in this review has been screened using various inclusion criteria. After screening, 62 studies remained for analysis, with two additional articles from the bibliography, were categorized into the following: (1) fatigue, (2) torque, (3) force, (4) stiffness, (5) electrode development, (6) reliability of MMG and NMES approaches, and (7) validation of these techniques in clinical monitoring. This review has found that MMG through NMES provides feature factors for muscle activity assessment, highlighting standardized electromyostimulation and MMG parameters from different experimental protocols. Despite the evidence of mathematical computations in quantifying MMG along with NMES, the requirement of the processing speed, and fluctuation of MMG signals influence the technique to be prone to errors. Interestingly, although this review does not focus on machine learning, there are only few studies that have adopted it as an alternative to statistical analysis in the assessment of muscle fatigue, torque, and force. The results confirm the need for further investigation on the use of sophisticated computations of features of MMG signals from electrically stimulated muscles in muscle function assessment and assistive technology such as prosthetics control.
Collapse
Affiliation(s)
- Raphael Uwamahoro
- Fakulti Kejuruteraan Elektronik & Kejuruteraan Komputer, Universiti Teknikal Malaysia Melaka, Tunggal, Malaysia
- Regional Centre of Excellence in Biomedical Engineering and E-Health, University of Rwanda, PO BOX 4285, Kigali, Rwanda
| | - Kenneth Sundaraj
- Fakulti Kejuruteraan Elektronik & Kejuruteraan Komputer, Universiti Teknikal Malaysia Melaka, Tunggal, Malaysia.
| | - Indra Devi Subramaniam
- Pusat Bahasa & Pembangunan Insan, Universiti Teknikal Malaysia Melaka, Tunggal, Malaysia
| |
Collapse
|
4
|
Bhardwaj S, Khan AA, Muzammil M. Lower limb rehabilitation robotics: The current understanding and technology. Work 2021; 69:775-793. [PMID: 34180443 DOI: 10.3233/wor-205012] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/14/2022] Open
Abstract
BACKGROUND With the increasing rate of ambulatory disabilities and rise in the elderly population, advance methods to deliver the rehabilitation and assistive services to patients have become important. Lower limb robotic therapeutic and assistive aids have been found to improve the rehabilitation outcome. OBJECTIVE The article aims to present the updated understanding in the field of lower limb rehabilitation robotics and identify future research avenues. METHODS Groups of keywords relating to assistive technology, rehabilitation robotics, and lower limb were combined and searched in EMBASE, IEEE Xplore Digital Library, Scopus, Web of Science and Google Scholar database. RESULTS Based on the literature collected from the databases we provide an overview of the understanding of robotics in rehabilitation and state of the art devices for lower limb rehabilitation. Technological advancements in rehabilitation robotic architecture (sensing, actuation and control) and biomechanical considerations in design have been discussed. Finally, a discussion on the major advances, research directions, and challenges is presented. CONCLUSIONS Although the use of robotics has shown a promising approach to rehabilitation and reducing the burden on caregivers, extensive and innovative research is still required in both cognitive and physical human-robot interaction to achieve treatment efficacy and efficiency.
Collapse
Affiliation(s)
- Siddharth Bhardwaj
- Department of Mechanical Engineering, Aligarh Muslim University, Aligarh, UP, India
| | - Abid Ali Khan
- Department of Mechanical Engineering, Aligarh Muslim University, Aligarh, UP, India
| | - Mohammad Muzammil
- Department of Mechanical Engineering, Aligarh Muslim University, Aligarh, UP, India
| |
Collapse
|
5
|
Assisted Grasping in Individuals with Tetraplegia: Improving Control through Residual Muscle Contraction and Movement. SENSORS 2019; 19:s19204532. [PMID: 31635286 PMCID: PMC6832396 DOI: 10.3390/s19204532] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 09/26/2019] [Revised: 10/14/2019] [Accepted: 10/15/2019] [Indexed: 11/16/2022]
Abstract
Individuals who sustained a spinal cord injury often lose important motor skills, and cannot perform basic daily living activities. Several assistive technologies, including robotic assistance and functional electrical stimulation, have been developed to restore lost functions. However, designing reliable interfaces to control assistive devices for individuals with C4–C8 complete tetraplegia remains challenging. Although with limited grasping ability, they can often control upper arm movements via residual muscle contraction. In this article, we explore the feasibility of drawing upon these residual functions to pilot two devices, a robotic hand and an electrical stimulator. We studied two modalities, supra-lesional electromyography (EMG), and upper arm inertial sensors (IMU). We interpreted the muscle activity or arm movements of subjects with tetraplegia attempting to control the opening/closing of a robotic hand, and the extension/flexion of their own contralateral hand muscles activated by electrical stimulation. Two groups were recruited: eight subjects issued EMG-based commands; nine other subjects issued IMU-based commands. For each participant, we selected at least two muscles or gestures detectable by our algorithms. Despite little training, all participants could control the robot’s gestures or electrical stimulation of their own arm via muscle contraction or limb motion.
Collapse
|
6
|
Chen J, Hu J, Leung AKL, Chen C, Zhang J, Zhang Y, Zhu Y, Han J. Shape Memory Ankle-Foot Orthoses. ACS APPLIED MATERIALS & INTERFACES 2018; 10:32935-32941. [PMID: 30221507 DOI: 10.1021/acsami.8b08851] [Citation(s) in RCA: 9] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/08/2023]
Abstract
Electrically actuated ankle-foot orthoses (AFOs) were designed and prototyped using shape memory textile composites. Acrylic copolymers were synthesized as the matrix to demonstrate shape memory effects, whereas electrothermal fabrics were embedded to generate uniform heat as a trigger. Superior to conventional polymeric orthoses, shape memory AFOs (SM-AFOs) could be repeatedly programmed at least 20 times with stable shape fixity and recovery. Evidenced by clinical practice, SM-AFOs were effectively actuated at 10 V, allowing the correction of ankle angles with 10° plantarflexion. Ultimately, we envision a smart orthopedic system that can advance progressive rehabilitation with manipulation under safe and convenient conditions.
Collapse
|
7
|
A Piezoresistive Sensor to Measure Muscle Contraction and Mechanomyography. SENSORS 2018; 18:s18082553. [PMID: 30081541 PMCID: PMC6111775 DOI: 10.3390/s18082553] [Citation(s) in RCA: 54] [Impact Index Per Article: 9.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 07/24/2018] [Revised: 07/31/2018] [Accepted: 08/01/2018] [Indexed: 11/17/2022]
Abstract
Measurement of muscle contraction is mainly achieved through electromyography (EMG) and is an area of interest for many biomedical applications, including prosthesis control and human machine interface. However, EMG has some drawbacks, and there are also alternative methods for measuring muscle activity, such as by monitoring the mechanical variations that occur during contraction. In this study, a new, simple, non-invasive sensor based on a force-sensitive resistor (FSR) which is able to measure muscle contraction is presented. The sensor, applied on the skin through a rigid dome, senses the mechanical force exerted by the underlying contracting muscles. Although FSR creep causes output drift, it was found that appropriate FSR conditioning reduces the drift by fixing the voltage across the FSR and provides voltage output proportional to force. In addition to the larger contraction signal, the sensor was able to detect the mechanomyogram (MMG), i.e., the little vibrations which occur during muscle contraction. The frequency response of the FSR sensor was found to be large enough to correctly measure the MMG. Simultaneous recordings from flexor carpi ulnaris showed a high correlation (Pearson's r > 0.9) between the FSR output and the EMG linear envelope. Preliminary validation tests on healthy subjects showed the ability of the FSR sensor, used instead of the EMG, to proportionally control a hand prosthesis, achieving comparable performances.
Collapse
|
8
|
Antonelli MG, Alleva S, Beomonte Zobel P, Durante F, Raparelli T. Powered off-road wheelchair for the transportation of tetraplegics along mountain trails. Disabil Rehabil Assist Technol 2017; 14:172-181. [PMID: 29219008 DOI: 10.1080/17483107.2017.1413431] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/18/2022]
Abstract
PURPOSE For off-road mobility, some manual or power assisted devices were conceived to be self-driven by paraplegics while for tetraplegics non power-assisted devices were conceived. These devices require one or more conductors who are subjected to a high physical demand thus potentially creating: precarious safety condition for the user an elevated physical demand of conductors could reduce the care and the attention to give to the user; the time of the outdoor adventure experience of the user could be limited. METHODS To address these issues, an innovative user-centered power assisted off-road wheelchair for the transportation of tetraplegics along mountain trails was developed. The device, structured like a trike, is driven by two healthy conductors; the user is placed in the middle of the frame. A movable seat provides for the transfer from the standard to the off-road wheelchair. An electrical motor, powered by a battery pack, provides for the actuation. All the design and prototype aspects, the control system and experimental tests are detailed. RESULTS The prototype satisfies mechanical, safety and duration requirements. No physical demand while using the device and for the transfer of the user to the device was identified. Fun and engaging tests were carried out and all the participants were involved. Implications for Rehabilitation The device has the potential to enhance the quality of life of tetraplegics in terms of new life experiences. The device revealed the real possibility of a full recreational experience, an enhanced participation and a better social integration of tetraplegics.
Collapse
Affiliation(s)
- Michele Gabrio Antonelli
- a Department of Industrial and Information Engineering and Economics , University of L'Aquila Via G. Gronchi , L'Aquila , Italy
| | - Stefano Alleva
- a Department of Industrial and Information Engineering and Economics , University of L'Aquila Via G. Gronchi , L'Aquila , Italy
| | - Pierluigi Beomonte Zobel
- a Department of Industrial and Information Engineering and Economics , University of L'Aquila Via G. Gronchi , L'Aquila , Italy
| | - Francesco Durante
- a Department of Industrial and Information Engineering and Economics , University of L'Aquila Via G. Gronchi , L'Aquila , Italy
| | - Terenziano Raparelli
- b Department of Mechanical and Aerospace Engineering , Politecnico di Torino Corso Duca degli Abruzzi , Torino , Italy
| |
Collapse
|
9
|
Lobo-Prat J, Kooren PN, Stienen AHA, Herder JL, Koopman BFJM, Veltink PH. Non-invasive control interfaces for intention detection in active movement-assistive devices. J Neuroeng Rehabil 2014; 11:168. [PMID: 25516421 PMCID: PMC4459663 DOI: 10.1186/1743-0003-11-168] [Citation(s) in RCA: 100] [Impact Index Per Article: 10.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/10/2014] [Accepted: 12/05/2014] [Indexed: 11/11/2022] Open
Abstract
Active movement-assistive devices aim to increase the quality of life for patients with neuromusculoskeletal disorders. This technology requires interaction between the user and the device through a control interface that detects the user’s movement intention. Researchers have explored a wide variety of invasive and non-invasive control interfaces. To summarize the wide spectrum of strategies, this paper presents a comprehensive review focused on non-invasive control interfaces used to operate active movement-assistive devices. A novel systematic classification method is proposed to categorize the control interfaces based on: (I) the source of the physiological signal, (II) the physiological phenomena responsible for generating the signal, and (III) the sensors used to measure the physiological signal. The proposed classification method can successfully categorize all the existing control interfaces providing a comprehensive overview of the state of the art. Each sensing modality is briefly described in the body of the paper following the same structure used in the classification method. Furthermore, we discuss several design considerations, challenges, and future directions of non-invasive control interfaces for active movement-assistive devices.
Collapse
Affiliation(s)
- Joan Lobo-Prat
- Department of Biomechanical Engineering, University of Twente, Drienerlolaan 5, 7522, NB, Enschede, The Netherlands.
| | - Peter N Kooren
- Department of Physics and Medical Technology, VU University Medical Center, Van der Boechorststraat 7, 1081 BT, Amsterdam, The Netherlands.
| | - Arno H A Stienen
- Department of Biomechanical Engineering, University of Twente, Drienerlolaan 5, 7522, NB, Enschede, The Netherlands. .,Department of Physical Therapy and Human Movement Sciences, Northwestern University, 645 N. Michigan Ave. Suite 1100, 60611, Chicago, IL, USA.
| | - Just L Herder
- Department of Precision and Microsystems Engineering, Delft University of Technology, Mekelweg 2, 2628 CD, Delft, The Netherlands. .,Department Mechanical Automation and Mechatronics, University of Twente, Drienerlolaan 5, 7500 AE, Enschede, The Netherlands.
| | - Bart F J M Koopman
- Department of Biomechanical Engineering, University of Twente, Drienerlolaan 5, 7522, NB, Enschede, The Netherlands.
| | - Peter H Veltink
- Department of Biomedical Signals and Systems, University of Twente, Drienerlolaan 5, 7500 AE, Enschede, The Netherlands.
| |
Collapse
|
10
|
Ibitoye MO, Hamzaid NA, Zuniga JM, Abdul Wahab AK. Mechanomyography and muscle function assessment: a review of current state and prospects. Clin Biomech (Bristol, Avon) 2014; 29:691-704. [PMID: 24856875 DOI: 10.1016/j.clinbiomech.2014.04.003] [Citation(s) in RCA: 68] [Impact Index Per Article: 6.8] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 10/31/2013] [Revised: 04/08/2014] [Accepted: 04/08/2014] [Indexed: 02/07/2023]
Abstract
Previous studies have explored to saturation the efficacy of the conventional signal (such as electromyogram) for muscle function assessment and found its clinical impact limited. Increasing demand for reliable muscle function assessment modalities continues to prompt further investigation into other complementary alternatives. Application of mechanomyographic signal to quantify muscle performance has been proposed due to its inherent mechanical nature and ability to assess muscle function non-invasively while preserving muscular neurophysiologic information. Mechanomyogram is gaining accelerated applications in evaluating the properties of muscle under voluntary and evoked muscle contraction with prospects in clinical practices. As a complementary modality and the mechanical counterpart to electromyogram; mechanomyogram has gained significant acceptance in analysis of isometric and dynamic muscle actions. Substantial studies have also documented the effectiveness of mechanomyographic signal to assess muscle performance but none involved comprehensive appraisal of the state of the art applications with highlights on the future prospect and potential integration into the clinical practices. Motivated by the dearth of such critical review, we assessed the literature to investigate its principle of acquisition, current applications, challenges and future directions. Based on our findings, the importance of rigorous scientific and clinical validation of the signal is highlighted. It is also evident that as a robust complement to electromyogram, mechanomyographic signal may possess unprecedented potentials and further investigation will be enlightening.
Collapse
Affiliation(s)
- Morufu Olusola Ibitoye
- Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia; Department of Biomedical Engineering, Faculty of Engineering and Technology, University of Ilorin, P. M. B. 1515 Ilorin, Nigeria.
| | - Nur Azah Hamzaid
- Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia.
| | - Jorge M Zuniga
- Department of Exercise Science, Creighton University, 2500 California Plaza, Kiewit Fitness center 228, Omaha, NE 68178, United States.
| | - Ahmad Khairi Abdul Wahab
- Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia.
| |
Collapse
|
11
|
Posatskiy A, Chau T. The effects of motion artifact on mechanomyography: A comparative study of microphones and accelerometers. J Electromyogr Kinesiol 2012; 22:320-4. [DOI: 10.1016/j.jelekin.2011.09.004] [Citation(s) in RCA: 41] [Impact Index Per Article: 3.4] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/02/2011] [Revised: 08/20/2011] [Accepted: 09/07/2011] [Indexed: 11/26/2022] Open
|
12
|
Posatskiy AO, Chau T. Design and evaluation of a novel microphone-based mechanomyography sensor with cylindrical and conical acoustic chambers. Med Eng Phys 2012; 34:1184-90. [PMID: 22227245 DOI: 10.1016/j.medengphy.2011.12.007] [Citation(s) in RCA: 36] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/28/2011] [Revised: 09/21/2011] [Accepted: 12/09/2011] [Indexed: 11/25/2022]
Abstract
Mechanomyography has recently been proposed as a control modality for alternative access technologies for individuals with disabilities. However, MMG recordings are highly susceptible to contamination from limb movements. Pressure-based transducers are touted to be the most robust to external movement although there is some debate about their optimal chamber geometry, in terms of low frequency gain and spectral flatness. To investigate the question of preferred geometry, transducers with cylindrical and conical chambers of varying dimensions were designed, manufactured and tested. Using a computer-controlled electrodynamic shaker, the frequency response of each chamber geometry was empirically derived. Of the cylindrical chambers, the highest gain and the flattest frequency response was exhibited by a chamber 10 mm in diameter and 5-7 mm in height. However, conical chambers offered an average rise in gain of 6.79 ± 1.06 dB/Hz over that achievable with cylindrical geometries. The highest gain and flattest response was achieved with a transducer consisting of a low-frequency MEMS microphone, a 4 μm aluminized mylar membrane and a rigid conical chamber 7 mm in diameter and 5mm in height. This design is recommended for MMG applications where limb movement is prevalent.
Collapse
Affiliation(s)
- A O Posatskiy
- Department of Mechanical and Industrial Engineering, University of Toronto, Toronto, ON, Canada.
| | | |
Collapse
|
13
|
Islam A, Sundaraj K, Ahmad B, Ahamed NU, Ali A. Mechanomyography Sensors for Muscle Assessment: a Brief Review. J Phys Ther Sci 2012. [DOI: 10.1589/jpts.24.1359] [Citation(s) in RCA: 10] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/24/2022] Open
Affiliation(s)
- Anamul Islam
- School of Computer and Communication Engineering, Universiti Malaysia Perlis
| | | | - Badlishah Ahmad
- School of Computer and Communication Engineering, Universiti Malaysia Perlis
| | | | - Asraf Ali
- School of Computer and Communication Engineering, Universiti Malaysia Perlis
| |
Collapse
|
14
|
Alves N, Chau T. Mechanomyography as an access pathway: corporeal contraindications. Disabil Rehabil Assist Technol 2011; 6:552-63. [DOI: 10.3109/17483107.2010.541323] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/13/2022]
|
15
|
Alves N, Chau T. The design and testing of a novel mechanomyogram-driven switch controlled by small eyebrow movements. J Neuroeng Rehabil 2010; 7:22. [PMID: 20492680 PMCID: PMC2890628 DOI: 10.1186/1743-0003-7-22] [Citation(s) in RCA: 27] [Impact Index Per Article: 1.9] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/11/2010] [Accepted: 05/21/2010] [Indexed: 11/17/2022] Open
Abstract
Background Individuals with severe physical disabilities and minimal motor behaviour may be unable to use conventional mechanical switches for access. These persons may benefit from access technologies that harness the volitional activity of muscles. In this study, we describe the design and demonstrate the performance of a binary switch controlled by mechanomyogram (MMG) signals recorded from the frontalis muscle during eyebrow movements. Methods Muscle contractions, detected in real-time with a continuous wavelet transform algorithm, were used to control a binary switch for computer access. The automatic selection of scale-specific thresholds reduced the effect of artefact, such as eye blinks and head movement, on the performance of the switch. Switch performance was estimated by cued response-tests performed by eleven participants (one with severe physical disabilities). Results The average sensitivity and specificity of the switch was 99.7 ± 0.4% and 99.9 ± 0.1%, respectively. The algorithm performance was robust against typical participant movement. Conclusions The results suggest that the frontalis muscle is a suitable site for controlling the MMG-driven switch. The high accuracies combined with the minimal requisite effort and training show that MMG is a promising binary control signal. Further investigation of the potential benefits of MMG-control for the target population is warranted.
Collapse
Affiliation(s)
- Natasha Alves
- Bloorview Research Institute, Bloorview Kids Rehab, Toronto, Ontario, Canada
| | | |
Collapse
|
16
|
|