Radical-Promoted Visible Light Photoinitiated Cationic Polymerization of Epoxides

Crosslinked Gel Polymer Electrolyte from Trimethylolpropane Triglycidyl Ether by In Situ Polymerization for Lithium-Ion Batteries

Electrolytes play a critical role in battery performance. They are associated with an increased risk of safety issues. The main challenge faced by many researchers is how to balance the physical and electrical properties of electrolytes. Gel polymer electrolytes (GPEs) have received increasing attention due to their satisfactory properties of ionic conductivity, mechanical stability, and safety. Herein, we develop a gel network polymer electrolyte (GNPE) to address the challenge mentioned earlier. This GNPE was formed by tri-epoxide monomer and bis(fluorosulfonyl)imide lithium salt (LiFSI) via an in situ cationic polymerization under mild thermal conditions. The obtained GNPE exhibited a relatively high ionic conductivity (σ) of 2.63 × 10-4 S cm-1, lithium transference number (tLi+, 0.58) at room temperature (RT), and intimate electrode compatibility with LiFePO4 and graphite. The LiFePO4/GNPE/graphite battery also showed a promising cyclic performance at RT, e.g., a suitable discharge specific capacity of 127 mAh g-1 and a high Coulombic efficiency (>97%) after 100 cycles at 0.2 C. Moreover, electrolyte films showed good mechanical stability and formed the SEI layer on the graphite anode. This study provides a facile method for preparing epoxy-based electrolytes for high-performance lithium-ion batteries (LIBs).

Recent Advances and Challenges in Long Wavelength Sensitive Cationic Photoinitiating Systems

With the advantages offered by cationic photopolymerization (CP) such as broad wavelength activation, tolerance to oxygen, low shrinkage and the possibility of "dark cure", it has attracted extensive attention in photoresist, deep curing and other fields in recent years. The applied photoinitiating systems (PIS) play a crucial role as they can affect the speed and type of the polymerization and properties of the materials formed. In the past few decades, much effort has been invested into developing cationic photoinitiating systems (CPISs) that can be activated at long wavelengths and overcome technical problems and challenges faced. In this article, the latest developments in the long wavelength sensitive CPIS under ultraviolet (UV)/visible light-emitting diodes (LED) lights are reviewed. The objective is, furthermore, to show differences as well as parallels between different PIS and future perspectives.

Recent developments in visible light induced polymerization towards its application to nanopores

Visible light induced polymerizations are a strongly emerging field in recent years. Besides the often mild reaction conditions, visible light offers advantages of spatial and temporal control over chain growth, which makes visible light ideal for functionalization of surfaces and more specifically of nanoscale pores. Current challenges in nanopore functionalization include, in particular, local and highly controlled polymer functionalizations. Using spatially limited light sources such as lasers or near field modes for light-induced polymer functionalization is envisioned to allow local functionalization of nanopores and thereby improve nanoporous material performance. These light sources are usually providing visible light while classical photopolymerizations are mostly based on UV-irradiation. In this review, we highlight developments in visible light induced polymerizations and especially in visible light induced controlled polymerizations as well as their potential for nanopore functionalization. Existing examples of visible light induced polymerizations in nanopores are emphasized.

Synthesis of Block Copolymers by Mechanistic Transformation from Reversible Complexation Mediated Living Radical Polymerization to the Photoinduced Radical Oxidation/Addition/Deactivation Process

A versatile strategy for the fabrication of block copolymers by the combination of two discrete living polymerization techniques─reversible complexation mediated living radical polymerization (RCMP) and photoinduced radical oxidation addition deactivation (PROAD) processes─is reported. First, RCMP is conducted to yield poly(methyl methacrylate) with iodide end groups (PMMA-I). In the following step, PMMA-I is used as macroinitiator for living PROAD cationic polymerization of isobutyl vinyl ether. Successful formation of the block copolymers is confirmed by ¹H NMR, FT-IR, GPC, and DSC investigations.

Review on UV-Induced Cationic Frontal Polymerization of Epoxy Monomers

Ultraviolet (UV)-induced cationic frontal polymerization has emerged as a novel technique that allows rapid curing of various epoxy monomers upon UV irradiation within a few seconds. In the presence of a diaryliodonium salt photoinitiator together with a thermal radical initiator, the cationic ring opening polymerization of an epoxide monomer is auto-accelerated in the form of a self-propagating front upon UV irradiation. This hot propagating front generates the required enthalpy to sustain curing reaction throughout the resin formulation without further need for UV irradiation. This unique reaction pathway makes the cationic frontal polymerization a promising route towards the efficient curing of epoxy-based thermosetting resins and related composite structures. This review represents a comprehensive overview of the mechanism and progress of UV-induced cationic frontal polymerization of epoxy monomers that have been reported so far in literature. At the same time, this review covers important aspects on the frontal polymerization of various epoxide monomers involving the chemistry of the initiators, the effect of appropriate sensitizers, diluents and fillers.

Photoinduced free radical promoted cationic polymerization 40 years after its discovery

Free radical promoted cationic photopolymerization has been described with its historical background, main principles and usage in polymer synthesis.

Design of Iodonium Salts for UV or Near-UV LEDs for Photoacid Generator and Polymerization Purposes

Iodonium salts are well established photoacid generators, cationic photoinitiators, as well as additives commonly used in photoredox catalytic cycles. However, as a strong limitation, iodonium salts are characterized by low light absorption properties for λ > 300 nm so that these latter cannot be activated with cheap, safe, and eco-friendly near UV or even visible light emitting diodes (LEDs). To overcome this drawback, the covalent linkage of an iodonium salt to a chromophore absorbing at longer wavelength is actively researched. With aim at red-shifting the absorption spectrum of the iodonium salt, the synthesis of new compounds combining within a unique chemical structure both the chromophore (here the naphthalimide scaffold) and the iodonium salt is presented. By mean of this strategy, a polymerization could be initiated at 365 nm with the modified iodonium salts whereas no polymerization could be induced with the benchmark iodonium salt i.e., Speedcure 938 at this specific wavelength. To examine the effect of the counter-anion on the photoinitiating ability of these different salts, five different counter-anions were used. Comparison between the different anions revealed the bis(trifluoromethane)sulfonimide salt to exhibit the best photoinitiating ability in both the free radical polymerization of acrylates and the cationic polymerization of epoxides. To support the experimental results, molecular orbital calculations have been carried out. By theoretical calculations, the initiating species resulting from the photocleavage of the iodonium salts could be determined. The cleavage selectivity and the photochemical reactivity of the new iodoniums are also discussed.

Controlled Synthesis of Block Copolymers by Mechanistic Transformation from Atom Transfer Radical Polymerization to Iniferter Process

A straightforward transformation protocol combining two distinct living polymerization methods for the controlled synthesis of block copolymers is described. In the first step, bromo-terminated poly(methyl methacrylate) is prepared by atom transfer radical polymerization (ATRP). Then, a bromide end group is substituted with a triphenylmethyl (trityl) functionality under visible light irradiation using dimanganese decacarbonyl (Mn₂ (CO)₁₀ ) photochemistry. The resulting polymers with trityl end groups are used as macroiniferter for the polymerization of styrene and tert-butyl acrylate (tBA) to yield desired block copolymers with narrow molecular weight distribution. Moreover, the amphiphilic copolymers with acrylic acid functionalities are obtained by the hydrolyzation of poly(tert-butyl acrylate) containing block copolymers with trifluoroacetic acid.

Optical Autocatalysis Establishes Novel Spatial Dynamics in Phase Separation of Polymer Blends during Photocuring

We report a fundamentally new nonlinear dynamic system that couples optical autocatalytic behavior to phase evolution in photoreactive binary polymer blends. Upon exposure to light, the blend undergoes spontaneous patterning into a dense arrangement of microscale polymer filaments. The filaments' growth in turn induces local spinodal decomposition of the blend along their length, thereby regulating the spatially dynamics of phase separation. This leads to the spontaneous organization of a large-scale binary phase morphology dictated by the filament arrangement. This is a new mechanism for polymer blend organization, which couples nonlinear optical dynamics to chemical phase separation dynamics, and offers a new approach to light-directed patterning and organization of polymer and hybrid blends.

Polyethylene-g-Polystyrene Copolymers by Combination of ROMP, Mn2(CO)10-Assisted TEMPO Substitution and NMRP

The synthesis of polyethylene-graft-polystyrene copolymers by a multistep "grafting from" approach is described. In the first step, a bromo-functional polyethylene (PE-Br) was synthesized via ring-opening metathesis polymerization (ROMP) of cis-cyclooctene (COE) and quantitative hydrobromination. Subsequent irradiation of PE-Br under visible light in the presence of dimanganese decacarbonyl (Mn₂(CO)₁₀) and 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) resulted in the formation of TEMPO-substituted polyethylene (PE-TEMPO). Polystyrene (PS) chains were then grown via nitroxide mediated radical polymerization (NMRP) from the PE-TEMPO precursor to give desired PE-g-PS copolymers in a controlled manner. The intermediates at each step and final graft copolymers were characterized by ¹H NMR, FT-IR, GPC, and DSC analyses.

Self-Strengthening Hybrid Dental Adhesive via Visible-light Irradiation Triple Polymerization

A self-strengthening methacrylate-based dental adhesive system was developed by introducing an epoxy cyclohexyl trimethoxysilane (TS) which contains both epoxy and methoxysilyl functional groups. The experimental formulation, HEMA/BisGMA/TS (22.5/27.5/50, wt%), was polymerized by visible-light. Real-time Fourier transform infrared spectroscopy (FTIR) was used to investigate in situ the free radical polymerization of methacrylate, ring-opening cationic polymerization of epoxy, and photoacid-induced sol-gel reactions. Among the three simultaneous reactions, the reaction rate of the free radical polymerization was the highest and the hydrolysis/condensation rate was the lowest. With 40s-irradiation, the degrees of conversion of the double bond and epoxy groups at 600 s were 73.2±1.2%, 87.9±2.4%, respectively. Hydrolysis of the methoxysilyl group was initially <5%, and increased gradually to about 50% after 48 h dark storage. Photoacids generated through the visible-light-induced reaction were effective in catalyzing both epoxy ring-opening polymerization and methoxysilyl sol-gel reaction. The mechanical properties of copolymers made with TS concentrations from 5 to 35 wt% were obtained using dynamic mechanical analysis (DMA). In wet conditions, the storage moduli at 70 °C and glass transition temperature were significantly higher than that of the control (p<0.05); these properties increased with TS concentration and storage time. The post reaction of hydrolysis/condensation of alkoxysilane could provide persistent strengthening whether in a neutral or acidic environment and these characteristics could lead to enhanced mechanical properties in the oral environment. The cumulative amount of leached species decreased significantly in the TS-containing copolymers. These results provide valuable information for the development of dental adhesives with reduced leaching of methacrylate monomers and enhanced mechanical properties under the wet, oral environment.

Mimicking nature: Self-strengthening properties in a dental adhesive

Chemical and enzymatic hydrolysis provoke a cascade of events that undermine methacrylate-based adhesives and the bond formed at the tooth/composite interface. Infiltration of noxious agents, e.g. enzymes, bacteria, and so forth, into the spaces created by the defective bond will ultimately lead to failure of the composite restoration. This paper reports a novel, synthetic resin that provides enhanced hydrolytic stability as a result of intrinsic reinforcement of the polymer network. The behavior of this novel resin, which contains γ-methacryloxyproyl trimethoxysilane (MPS) as its Si-based compound, is reminiscent of self-strengthening properties found in nature. The efforts in this paper are focused on two essential aspects: the visible-light irradiation induced (photoacid-induced) sol-gel reaction and the mechanism leading to intrinsic self-strengthening. The FTIR band at 2840cm(-1) corresponding to CH3 symmetric stretch in -Si-O-CH3 was used to evaluate the sol-gel reaction. Results from the real-time FTIR indicated that the newly developed resin showed a limited sol-gel reaction (<5%) during visible-light irradiation, but after 48h dark storage, the reaction was over 65%. The condensation of methoxysilane mainly occurred under wet conditions. The storage moduli and glass transition temperature of the copolymers increased in wet conditions with the increasing MPS content. The cumulative amounts of leached species decreased significantly when the MPS-containing adhesive was used. The results suggest that the polymethacrylate-based network, which formed first as a result of free radical initiated polymerization, retarded the photoacid-induced sol-gel reaction. The sol-gel reaction provided a persistent, intrinsic reinforcement of the polymer network in both neutral and acidic conditions. This behavior led to enhanced mechanical properties of the dental adhesives under conditions that simulate the wet, oral environment.

STATEMENT OF SIGNIFICANCE

A self-strengthening dental adhesive system was developed through a dual curing process, which involves the free radical photopolymerization followed by slow hydrolysis and condensation (photoacid-induced sol-gel reaction) of alkoxylsilane groups. The concept of "living" photoacid-induced sol-gel reaction with visible-light irradiation was confirmed in the polymer. The sol-gel reaction was retarded by the polymethacrylate network, which was generated first; the network extended the life and retained the activity of silanol groups. The self-strengthening behavior was evaluated by monitoring the mechanical properties of the hybrid copolymers under wet conditions. The present research demonstrates the sol-gel reaction in highly crosslinked network as a potentially powerful strategy to prolong the functional lifetime of engineered biomaterials in wet environments.

Photoinduced Electron Transfer Reactions for Macromolecular Syntheses

Photochemical reactions, particularly those involving photoinduced electron transfer processes, establish a substantial contribution to the modern synthetic chemistry, and the polymer community has been increasingly interested in exploiting and developing novel photochemical strategies. These reactions are efficiently utilized in almost every aspect of macromolecular architecture synthesis, involving initiation, control of the reaction kinetics and molecular structures, functionalization, and decoration, etc. Merging with polymerization techniques, photochemistry has opened up new intriguing and powerful avenues for macromolecular synthesis. Construction of various polymers with incredibly complex structures and specific control over the chain topology, as well as providing the opportunity to manipulate the reaction course through spatiotemporal control, are one of the unique abilities of such photochemical reactions. This review paper provides a comprehensive account of the fundamentals and applications of photoinduced electron transfer reactions in polymer synthesis. Besides traditional photopolymerization methods, namely free radical and cationic polymerizations, step-growth polymerizations involving electron transfer processes are included. In addition, controlled radical polymerization and "Click Chemistry" methods have significantly evolved over the last few decades allowing access to narrow molecular weight distributions, efficient regulation of the molecular weight and the monomer sequence and incredibly complex architectures, and polymer modifications and surface patterning are covered. Potential applications including synthesis of block and graft copolymers, polymer-metal nanocomposites, various hybrid materials and bioconjugates, and sequence defined polymers through photoinduced electron transfer reactions are also investigated in detail.

A novel naphthalimide scaffold based iodonium salt as a one-component photoacid/photoinitiator for cationic and radical polymerization under LED exposure

A strong drawback to overcome for photoinitiators of cationic polymerization or photoacids is their low photosensitivity for long wavelengths.

Recent Developments of Versatile Photoinitiating Systems for Cationic Ring Opening Polymerization Operating at Any Wavelengths and under Low Light Intensity Sources

Photoinitiators (PI) or photoinitiating systems (PIS) usable in light induced cationic polymerization (CP) and free radical promoted cationic polymerization (FRPCP) reactions (more specifically for cationic ring opening polymerization (ROP)) together with the involved mechanisms are briefly reviewed. The recent developments of novel two- and three-component PISs for CP and FRPCP upon exposure to low intensity blue to red lights is emphasized in details. Examples of such reactions under various experimental conditions are provided.

Enhanced visible radiation photopolymerization of dimethacrylates with the three component thioxanthone (CPTXO)–amine–iodonium salt system

The three component thioxanthone/iodonium/amine visible light photoinitiator system is four times more efficient due to irreversible oxidation of the ketyl and the amine radicals by the iodonium salt and the regeneration of the thioxanthone and produce twice as many active radicals.

One/two-photon-sensitive photoacid generators based on benzene oligomer-containing D–π–A-type aryl dialkylsulfonium salts

D–π–A type photoacid generators with a benzene-oligomer as π-conjugated systems show high photoacid generation efficiency (Φ_H+max > 0.7) and good photoinitiated polymerization abilities by 365 nm and 780 nm excitation.

π-conjugated sulfonium-based photoacid generators: an integrated molecular approach for efficient one and two-photon polymerization

D–π–A type π-conjugated photoacid generators through the para-to-meta substitution strategy show high efficiency in photoinitiated cationic polymerization reactions at 405 nm and 800 nm excitation.

N-Vinylcarbazole: An Additive for Free Radical Promoted Cationic Polymerization upon Visible Light

N-Vinylcarbazole is proposed as an additive for epoxy ring-opening polymerization ROP upon visible light exposure. This compound can convert hardly oxidizable radicals to carbon centered radicals by an addition process onto the N-vinylcarbazole double bond. The generated radicals can be further easily oxidized by an iodonium salt thereby leading to efficient initiating cations for the ROP of epoxides. Different visible light photoinitiating systems have been investigated: Type I photoinitiators (derived from phosphine oxides) and dye/iodonium salt couples. The underlying chemical mechanisms are investigated by electron spin resonance (ESR) experiments.

A novel photopolymerization initiating system based on an iridium complex photocatalyst

The use of a photocatalyst (tris(2-phenylpyridine)iridium [Ir(ppy)(3)]) being able to generate both radicals and cations to initiate free radical polymerization and ring opening polymerization is presented. Remarkably, under soft irradiations (fluorescence bulb, sunlight), excellent cationic polymerization profiles and final conversions are obtained. The involved mechanisms are investigated by ESR experiments.

Recent advances and developments in composite dental restorative materials

Composite dental restorations represent a unique class of biomaterials with severe restrictions on biocompatibility, curing behavior, esthetics, and ultimate material properties. These materials are presently limited by shrinkage and polymerization-induced shrinkage stress, limited toughness, the presence of unreacted monomer that remains following the polymerization, and several other factors. Fortunately, these materials have been the focus of a great deal of research in recent years with the goal of improving restoration performance by changing the initiation system, monomers, and fillers and their coupling agents, and by developing novel polymerization strategies. Here, we review the general characteristics of the polymerization reaction and recent approaches that have been taken to improve composite restorative performance.

New thioxanthone and xanthone photoinitiators based on silyl radical chemistry

New cleavable photoinitiators are presented. As demonstrated here, combining the thioxanthone/xanthone (or other PI skeletons) and silyl chemistries should open up a new promising direction of research.

Recent advances in sunlight induced polymerization: role of new photoinitiating systems based on the silyl radical chemistry

Silyl radical chemistry opens new opportunities for photoinitiating systems for sunlight polymerization.