Preparations and application of dust suppressants from biomass-based materials

Biodegradable dust suppressants prepared from biomass-based materials: The role of viscosity and suppressed particles

In this study, biodegradable dust suppressants were prepared using glycerol and biomass-based oily compounds, including palm oil, biodiesel, and soybean oil. The suppressing ability of the glycerol and the oily compound mixture was evaluated using wind tunnel tests, and factors affecting the suppression of the particles were determined. The replacement of sodium dodecyl sulfate with coco glucoside and lauryl glucoside significantly enhanced the biodegradability of the suppressants (2.02 vs. 9.01 and 8.54 mg/L of BOD5). The glycerol and soybean oil mixture exhibited excellent performance owing to the relatively high viscosity of the suppressants, and the optimal dilution ratio was 1:50 and 1:1000 for sand and granite-weathered soil, respectively. More than 98% of suppression was obtained under the optimal conditions. The effect of the particle properties (particularly permeability) was significant, even though the viscosity of the suppressants was responsible for the suppression of the particles. Our results suggest that the mixture of glycerol and biomass-based oily compounds could be a promising suppressant for reducing the mobility of ultrafine particles in the atmosphere.Implications: Since the early 2010s, anthropogenic fugitive dust from industrial activities has become a serious environmental issue due to its serious hazards to the environment and human health in South Korea. So far, several dust suppressants (mostly salts) were made and used for field application. However, due to their toxic effects, it is necessary to develop a new eco-friendly suppressant that can be biodegraded in the soil and that is not hazardous to human health or the environment. Previously we have developed an eco-friendly dust suppressant with low toxicity and high suppression ability using ingredients and by-products of biodiesel production, marine biomass, and commercial vegetable oils (Tsgot and Oh 2021, J. Air Waste Manag. Assoc. 71:1386-1396). However, due to the low biodegradability of surfactant, the synthesized dust suppressants showed limited biodegradability. As a follow-up to our previous study, we employed readily biodegradable surfactants as additives to enhance the biodegradability of the dust suppressants with the same excellent suppressing ability. To determine the optimal conditions, the synthesis and preparation of the dust suppressants was conducted using biodegradable surfactants, including coco glucoside and lauryl glucoside. The factors affecting the suppressing ability of the suppressants were examined via wind tunnel tests. These factors include the dilution factors, the viscosity of the suppressants, and the type of suppressed particles. Possible suppressing mechanisms were also discussed.

Part 2: Stabilization/Containment of Radiological Particle Contamination to Enhance First Responder, Early Phase Worker, and Public Safety

The application of stabilization technologies to a radiologically contaminated surface has the potential for reducing the spread of contamination and, as a result, decreasing worker exposure to radiation. Three stabilization technologies, calcium chloride (CaCl2), flame retardant Phos-Chek® MVP-Fx, and Soil2O™ were investigated to evaluate their ability to reduce the resuspension and tracking of radiological contamination during response activities such as vehicle and foot traffic. Concrete pavers, asphalt pavers, and sandy soil walking paths were used as test surfaces, along with simulated fallout material (SFM) tagged with radiostrontium (Sr-85) applied as the contaminant. Radiological activities were measured using gamma spectrometry before and after simulated vehicle operation and foot traffic experiments, conducted with each stabilization technology and without application as a nonstabilized control. These measurements were acquired separately for each combination of surface and vehicle/foot traffic experiment. The resulting data describes the extent of SFM removed from each surface onto the tires or boots, the extent of SFM transferred to adjacent surfaces, and the residual SFM remaining on the tires or boots after each experiment. The type of surface and response worker actions influenced the stabilization results. For instance, when walked over, less than 2% of particles were removed from nonstabilized concrete, 4% from asphalt, and 40% of the particles were removed from the sand surface. By contrast, for vehicle experiments, ~40% of particles were again removed from the sand, but 7% and 15% from concrete and asphalt, respectively. In most cases, the stabilization technologies did provide improved stabilization. The improvement was related to the type of surface, worker actions, and stabilizer; a statistical analysis of these variables is presented. Overall, the results suggest an ability to utilize these technologies during the planning and implementation of response activities involving foot and vehicle traffic. In addition, resuspension of aerosolizable range SFM was monitored during walking path foot traffic experiments, and all stabilizing agents decreased the measured radioactivity, with the Soil2O™ decrease being 3 fold, whereas the CaCl2 and Phos-Chek MVP-Fx surfaces generated no detectable radioactivity. Overall, these results suggest that the stabilization technologies decrease the availability of particles respirable by response workers under these conditions.