Hand-held photoionization instruments for quantitative detection of sarin vapor and for rapid qualitative screening of contaminated objects

Intra-workday fluctuations of airborne contaminant concentration and the time-weighted average

Air contaminant concentrations vary between and within workdays and are often measured across a workday by passing a known air volume through a collection device. Laboratory analysis determines the contaminant mass trapped, providing a time-weighted average air concentration (C_TWA). This approach was driven by the best technologies available as exposure measurement processes developed and accuracy and measurement precision were sought. However, all integrated concentration•time (C•t) values determining C_TWA are equally weighted in assessing exposures, intra-workday concentration variability is unknown, and results are available days later. At times inappropriately, an occupational exposure limit (OEL) expressed as a C_TWA also requires equal weighting of all C•t values across an exposure period following concepts of Haber's law. Continuous monitoring (real-time detection) informs both the C_TWA and the variability of C during sampling, which are needed for stressors where a ceiling or peak OEL exists, for dangerous exposures to permanent gas-type contaminants, and for immediately dangerous to life or health (IDLH) conditions. Selective and accurate real-time detection instruments are not available for all air contaminants, but exposure magnitude information may be provided. The large amounts of data from continuous monitoring and the ability to correlate exposure maxima to specific tasks are also important. An exposure assessment role exists for selective and nonselective monitors, and in some cases, similar accuracy and precision are provided compared to laboratory analyses. Continuous monitoring may be of value when the alternative is the collection of a few C_TWA data points. Digitized personal monitor data can support the automation of some exposure control decisions or allow such decisions to be made by people in near real-time. The emerging Internet of Things (IoT) offers opportunities to integrate digital exposure data into decision-making to increase both efficiency and safety. The perceived and real uncertainty associated with real-time exposure assessments may be lessened with work to rule out the presence of know interferents and confirm the presence of target analytes.

SAW Chemical Array Device Coated with Polymeric Sensing Materials for the Detection of Nerve Agents

G nerve agents are colorless, odorless, and lethal chemical warfare agents (CWAs). The threat of CWAs, which cause critical damage to humans, continues to exist, e.g., in warfare or terrorist attacks. Therefore, it is important to be able to detect these agents rapidly and with a high degree of sensitivity. In this study, a surface acoustic wave (SAW) array device with three SAW sensors coated with different sensing materials and one uncoated sensor was tested to determine the most suitable material for the detection of nerve agents and related simulants. The three materials used were polyhedral oligomeric silsesquioxane (POSS), 1-benzyl-3-phenylthiourea (TU-1), and 1-ethyl-3-(4-fluorobenzyl) thiourea (TU-2). The SAW sensor coated with the POSS-based polymer showed the highest sensitivity and the fastest response time at concentrations below the median lethal concentration (LCt₅₀) for tabun (GA) and sarin (GB). Also, it maintained good performance over the 180 days of exposure tests for dimethyl methylphosphonate (DMMP). A comparison of the sensitivities of analyte vapors also confirmed that the sensitivity for DMMP was similar to that for GB. Considering that DMMP is a simulant which physically and chemically resembles GB, the sensitivity to a real agent of the sensor coated with POSS could be predicted. Therefore, POSS, which has strong hydrogen bond acid properties and which showed similar reaction characteristics between the simulant and the nerve agent, can be considered a suitable material for nerve agent detection.

Unraveling fabrication and calibration of wearable gas monitor for use under free-living conditions

Volatile organic compounds (VOC) are organic chemicals that have high vapor pressure at regular conditions. Some VOC could be dangerous to human health, therefore it is important to determine real-time indoor and outdoor personal exposures to VOC. To achieve this goal, our group has developed a wearable gas monitor with a complete sensor fabrication and calibration protocol for free-living conditions. Correction factors for calibrating the sensors, including sensitivity, aging effect, and temperature effect are implemented into a Quick Response Code (QR code), so that the pre-calibrated quartz tuning fork (QTF) sensor can be used with the wearable monitor under free-living conditions.

A Novel Wireless Wearable Volatile Organic Compound (VOC) Monitoring Device with Disposable Sensors

A novel portable wireless volatile organic compound (VOC) monitoring device with disposable sensors is presented. The device is miniaturized, light, easy-to-use, and cost-effective. Different field tests have been carried out to identify the operational, analytical, and functional performance of the device and its sensors. The device was compared to a commercial photo-ionization detector, gas chromatography-mass spectrometry, and carbon monoxide detector. In addition, environmental operational conditions, such as barometric change, temperature change and wind conditions were also tested to evaluate the device performance. The multiple comparisons and tests indicate that the proposed VOC device is adequate to characterize personal exposure in many real-world scenarios and is applicable for personal daily use.

The use of a photoionization detector to detect harmful volatile chemicals by emergency personnel

Objective

The objective of this investigation was to determine if a photoionization detector (PID) could be used to detect the presence of a simulated harmful chemical on simulated casualties of a chemical release.

Methods

A screening protocol, based on existing radiation screening protocols, was developed for the purposes of the investigation. Three simulated casualties were contaminated with a simulated chemical agent and two groups of emergency responders were involved in the trials. The success–failure ratio of the participants was used to judge the performance of the PID in this application.

Results

A high success rate was observed when the screening protocol was properly adhered to (97.67%). Conversely, the success rate suffered when participants deviated from the protocol (86.31%). With one exception, all failures were noted to have been the result of a failure to correctly observe the established screening protocol.

Conclusions

The results of this investigation indicate that the PID may be an effective screening tool for emergency responders. However, additional study is necessary to both confirm the effectiveness of the PID and refine the screening protocol if necessary.