Results of inspections in health hazard industries in a region of the state of Washington

Occupational Health and Safety Statistics as an Indicator of Worker Physical Health in South African Industry

Operations in general industry, including manufacturing, expose employees to a myriad of occupational health hazards. To prevent exposure, occupational health and safety regulations were enacted, with both employers and workers instituting various risk reduction measures. The analysis of available occupational disease and injury statistics (indicators of worker physical health) can be used to infer the effectiveness of risk reduction measures and regulations in preventing exposure. Thus, using the READ approach, analyses of occupational disease and injury statistics from South African industry, derived from annual reports of the Compensation Fund, were conducted. The publicly available database of occupational disease and injury statistics from the South African general industry is unstructured, and the data are inconsistently reported. This data scarcity, symptomatic of an absence of a functional occupational disease surveillance system, complicates judgement making regarding the effectiveness of implemented risk reduction measures, enacted occupational health and safety regulations and the status of worker physical health from exposure to workplace hazards. The statistics, where available, indicate that workers continue to be exposed to occupational health impacts within general industry, notwithstanding risk reduction measures and enacted regulations. In particular, worker physical health continues to be impacted by occupational injuries and noise-induced hearing loss. This is suggestive of shortcomings and inefficiencies in industry-implemented preventive measures and the regulatory state. A robust national occupational disease surveillance system is a regulatory tool that should detect and direct policy responses to identified occupational health hazards.

Prevalence of hearing loss among noise-exposed workers within the services sector, 2006-2015

OBJECTIVE

The purpose of this study is to estimate the prevalence of hearing loss among noise-exposed U.S. workers within the Services sector.

METHODS

Audiograms for 1.9 million workers (158,436 within Services) from 2006 to 2015 were examined. Prevalence and adjusted risk for hearing loss as compared with a reference industry were estimated for the Services sector/sub-sectors, and all industries combined.

RESULTS

The prevalence of hearing loss within Services was 17 compared to 16% for all industries combined. However, many sub-sectors greatly exceeded the overall prevalence (10-33% higher) and/or had adjusted risks significantly higher than the reference industry. Workers in Administration of Urban Planning and Community and Rural Development had the highest prevalence (50%), and workers in Solid Waste Combustors and Incinerators had more than double the risk, the highest of any sub-sector. Some sub-sectors traditionally viewed as 'low-risk' also had high prevalences and risks.

CONCLUSIONS

Large numbers of workers within Services have an elevated risk of hearing loss and need immediate hearing conservation efforts. Additional research and surveillance are needed for sub-sectors for which there is low awareness of hearing hazards or a lack of hearing data.

Disclosure and Fit Capability of the Filtering Facepiece Respirator

The filtering facepiece air-purifying respirator is annually purchased in the tens of millions and widely used for worker protection from harmful airborne particulates. The workplace consumers of this safety product, i.e., employers, workers, and safety and health professionals, have assurances of its effectiveness through the respirator certification and disclosure requirements of the National Institute for Occupational Safety and Health. However, the certification of a critical performance requirement has been missing for the approved filtering facepiece respirator since 1995: fit capability. Without this certification, consumers continue to be at risk of purchasing a respirator model that may fit a small percentage of the intended users. This commentary updates and expands an earlier one by this author, addresses the consequences of poorly fitting certified models on the market and lack of disclosure, and calls for further action by National Institute for Occupational Safety and Health to meet the needs and expectations of the consumer.

Determinants of respirable silica exposure in stone countertop fabrication: a preliminary study

A preliminary study of personal exposure to respirable quartz was conducted in four shops that used a variety of wet and dry methods to fabricate countertops from granite and quartz-containing synthetic stone-like materials. Full-shift time-weighted average (TWA) exposures exceeded the ACGIH threshold limit value of 0.025 mg/m(3) for all workers who used dry fabrication methods, even for very limited time, during any part of the work shift (n = 15 person-days). The geometric mean of exposures for workers who used dry methods extensively was about 1 mg/m(3) (n = 12 person-days). Workers who operated only automated or remotely controlled stone cutting or shaping equipment had calculated TWA exposures of approximately 0.02 mg/m(3) (n = 3 person-days). Task-specific geometric mean exposures for various wet and dry manual operations were ranked based on estimated concentrations extracted from multi-task partial-shift sample results using a linear algebra procedure. Limited use of dry methods was observed in shops that had previously reported using only wet methods. These results suggest that even shops that report using only wet methods might, in fact, resort to brief use of dry methods for specific operations. Therefore, there may be reason for concern over potential overexposure to respirable quartz in all stone countertop shops.

Prevalence of dry methods in granite countertop fabrication in Oklahoma

Granite countertop fabricators are at risk of exposure to respirable crystalline silica, which may cause silicosis and other lung conditions. The purpose of this study was to estimate the prevalence of exposure control methods, especially wet methods, in granite countertop fabrication in Oklahoma to assess how many workers might be at risk of overexposure to crystalline silica in this industry. Granite fabrication shops in the three largest metropolitan areas in Oklahoma were enumerated, and 47 of the 52 shops participated in a survey on fabrication methods. Countertop shops were small businesses with average work forces of fewer than 10 employees. Ten shops (21%) reported using exclusively wet methods during all fabrication steps. Thirty-five shops (74%) employing a total of about 200 workers reported using dry methods all or most of the time in at least one fabrication step. The tasks most often performed dry were edge profiling (17% of shops), cutting of grooves for reinforcing rods (62% of shops), and cutting of sink openings (45% of shops). All shops reported providing either half-face or full-face respirators for use during fabrication, but none reported doing respirator fit testing. Few shops reported using any kind of dust collection system. These findings suggest that current consumer demand for granite countertops is giving rise to a new wave of workers at risk of silicosis due to potential overexposure to granite dust.

A must for NIOSH: certify fit performance of the half mask particulate respirator

The National Institute for Occupational Safety and Health has proposed to amend the certification rules for half mask air-purifying particulate respirators. The amendment would require the certified respirator to fit a minimum percentage of the intended users. The fail/pass rate for a respirator fitting a worker population has not been part of the certification process for particulate respirators since 1995. The amendment would also add a new requirement for the manufacturer to inform whom the respirator is intended to fit.

Surveillance of Washington OSHA exposure data to identify uncharacterized or emerging occupational health hazards

Chemical substance exposure data from the Washington State Occupational Safety and Health Administration (OSHA) program were reviewed to determine if inspections conducted as a result of a report of a hazard from a complainant or referent may alert the agency to uncharacterized or emerging health hazards. Exposure and other electronically stored data from 6890 health inspection reports conducted between April 2003 and August 2008 were extracted from agency records. A total of 515 (7%) inspections with one or more personal airborne chemical substance samples were identified for further study. Inspections by report of a hazard and by targeting were compared for the following: number of inspections, number and percentage of inspections with workers exposed to substances above an agency's permissible exposure limit, types of industries inspected, and number and type of chemical substances assessed. Report of a hazard inspections documented work sites with worker overexposure at the same rate as agency targeted inspections (approximately 35% of the time), suggesting that complainants and referents are a credible pool of observers capable of directing the agency to airborne chemical substance hazards. Report of a hazard inspections were associated with significantly broader distribution of industries as well as a greater variety of chemical substance exposures than were targeted inspections. Narrative text that described business type and processes inspected was more useful than NAICS codes alone and critical in identifying processes and industries that may be associated with new hazards. Finally, previously identified emerging hazards were found among the report of a hazard data. These findings indicate that surveillance of OSHA inspection data can be a valid tool to identify uncharacterized and emerging health hazards. Additional research is needed to develop criteria for objective review and prioritization of the data for intervention. Federal OSHA and other state OSHA agencies will need to add electronic data entry fields more descriptive of industry, process, and substance to fully use agency exposure data for hazard surveillance.