Spectrofluorimetric Protocol for Estimation of Commonly Used Antispasmodic Drotaverine. Fluorescence Quenching Study

A fast, simple, accurate, precise, and cheap fluorimetric protocol has been proposed for analysis of a phosphodiesterase-IV inhibitor, namely drotaverine hydrochloride. Fluorimetric protocol is based on estimating the decrease in the eosin Y fluorescence intensity by quantitative addition of drotaverine at pH 3.1 (acetate buffer). An ion pair complex is formed, which leads to quenching in the fluorescence intensity of the dye without need of prior extraction at 534 nm (λex. 339 nm). Different reaction perimeters which influence the production of complex (ion pair between drotaverine and eosin) were deeply investigated and optimized. The developed fluorimetric protocol is capable for quantitative estimation of drotaverine in linear range of 0.4 to 2.5 µg mL-1. After method validation in respect to ICH guidelines, it was applied to determine drotaverine in its commercial preparation. By comparing with other reported method, the developed and validated fluorimetric protocol is capable for estimation of drotaverine in commercial preparation with good accuracy and excellent precision.

Potentiometric flow injection system for determination of reductants using a polymeric membrane permanganate ion-selective electrode based on current-controlled reagent delivery

A polymeric membrane permanganate-selective electrode has been developed as a current-controlled reagent release system for potentiometric detection of reductants in flow injection analysis. By applying an external current, diffusion of permanganate ions across the polymeric membrane can be controlled precisely. The permanganate ions released at the sample-membrane interface from the inner filling solution of the electrode are consumed by reaction with a reductant in the sample solution thus changing the measured membrane potential, by which the reductant can be sensed potentiometrically. Ascorbate, dopamine and norepinephrine have been employed as the model reductants. Under the optimized conditions, the potential peak heights are proportional to the reductant concentrations in the ranges of 1.0×10(-5) to 2.5×10(-7)M for ascorbate, of 1.0×10(-5) to 5.0×10(-7)M for dopamine, and of 1.0×10(-5) to 5.0×10(-7)M for norepinephrine, respectively with the corresponding detection limits of 7.8×10(-8), 1.0×10(-7) and 1.0×10(-7)M. The proposed system has been successfully applied to the determination of reductants in pharmaceutical preparations and vegetables, and the results agree well with those of iodimetric analysis.

Simultaneous determination of nifuroxazide and drotaverine hydrochloride in pharmaceutical preparations by bivariate and multivariate spectral analysis

The quantitative predictive abilities of the new and simple bivariate spectrophotometric method are compared with the results obtained by the use of multivariate calibration methods [the classical least squares (CLS), principle component regression (PCR) and partial least squares (PLS)], using the information contained in the absorption spectra of the appropriate solutions. Mixtures of the two drugs Nifuroxazide (NIF) and Drotaverine hydrochloride (DRO) were resolved by application of the bivariate method. The different chemometric approaches were applied also with previous optimization of the calibration matrix, as they are useful in simultaneous inclusion of many spectral wavelengths. The results found by application of the bivariate, CLS, PCR and PLS methods for the simultaneous determinations of mixtures of both components containing 2-12microgml(-1) of NIF and 2-8microgml(-1) of DRO are reported. Both approaches were satisfactorily applied to the simultaneous determination of NIF and DRO in pure form and in pharmaceutical formulation. The results were in accordance with those given by the EVA Pharma reference spectrophotometric method.

Spectrophotometric determination of pipazethate HCl, dextromethorphan HBr and drotaverine HCl in their pharmaceutical preparations

A simple, accurate and highly sensitive spectrophotometric method is proposed for the rapid determination of pipazethate hydrochloride, dextromethorphan hydrobromide and drotaverine hydrochloride using chromotrope 2B (C2B) and chromotrope 2R (C2R). The method consists of extracting the formed ion-associates into chloroform in the case of pipazethate HCl and dextromethorphan HBr or into methylene chloride in the case of drotaverine HCl. The ion-associates exhibit absorption maxima at 528, 540 and 532 nm with C2B and at 526, 517 and 522 nm with C2R for pipazethate HCl, dextromethorphan HBr and drotaverine HCl, respectively. The calibration curves resulting from the measurements of absorbance-concentration relations (at the optimum reaction conditions) of the extracted ion-pairs are linear over the concentration range 4.36-52.32 microg mL(-1) for pipazethate, 3.7-48.15 microg mL(-1) for dextromethorphan and 4.34-60.76 microg mL(-1) for drotaverine, respectively. The effect of acidity, reagent concentration, time, solvent and stoichiometric ratio of the ion-associates were estimated. The molar absorptivity and Sandell sensitivity of the reaction products were calculated. Statistical treatment of the results reflects that the procedure is precise, accurate and easily applied for the determination of the drugs under investigation in pure form and in their pharmaceutical preparations.

Improving the detection limits of antispasmodic drugs electrodes by using modified membrane sensors with inner solid contact

Three coated wire electrodes (CWEs) for the antispasmodic drugs; dicyclomine (Dc), mebeverine (Mv) and drotaverine (Dv) hydrochlorides were developed. Each electrode based on ion-associate of a heteropoly anion with the drug cation incorporated in membrane sensor modified with graphite and deposited on silver internal solid contact. The influence of addition of graphite to the membranes and the type of the internal solid contact on the potentiometric responses of the electrodes was investigated. The characteristics of the new electrodes were compared to the characteristics of previously reported traditional liquid inner contact electrodes of the same drugs. The lower detection limits of the proposed electrodes were somewhat better than those observed with the corresponding liquid contact ISEs and reached (1.2-2.0)x10(-7)M. The potentiometric selectivity of the CWEs revealed a significant improvement and much faster response times compared to the liquid contact ISEs. The practical utility of each electrode has been demonstrated by using it successfully in potentiometric determination of its respective drug in pharmaceutical preparations both in batch and flow injection conditions. Each electrode was also used as an indicator electrode in the potentiometric titration of the drug against standard silicotungstic acid and in potentiometric determination of the drug concentration in urine samples.

Flow injection analysis with tubular membrane ion-selective electrode and coated wires for buspirone hydrochloride

New Plastic membrane ion-selective electrode for buspirone hydrochloride based on buspironium tetraphenylborate was prepared. The electrode exhibited mean slope of calibration graph of 58.4 mV per decade of BusCl concentration at 25 degrees C. The electrode can be used within the concentration range 6.3 x 10(-5) - 10(-2) M BusCl at a pH range of 2.5-7.0. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal temperature coefficient of the electrode, amounting to 0.00056 V degrees C(-1). The electrode showed a very good selectivity for BusCl with respect to a number of inorganic cations, sugars and amino acids. The electrode was applied to the potentiometric determination of the buspirone ion and its pharmaceutical preparation under batch and flow injection conditions. Also, buspirone was determined by conductimetric titrations. Graphite rod, copper and silver coated wire electrodes were prepared and characterized as sensors for the drug under investigation.