1
|
Fujimoto T, Monzen H, Nakata M, Okada T, Yano S, Takakura T, Kuwahara J, Sasaki M, Higashimura K, Hiraoka M. Dosimetric shield evaluation with tungsten sheet in 4, 6, and 9MeV electron beams. Phys Med 2014; 30:838-42. [PMID: 24953537 DOI: 10.1016/j.ejmp.2014.05.009] [Citation(s) in RCA: 17] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 02/12/2014] [Revised: 05/25/2014] [Accepted: 05/27/2014] [Indexed: 10/25/2022] Open
Abstract
In electron radiotherapy, shielding material is required to attenuate beam and scatter. A newly introduced shielding material, tungsten functional paper (TFP), has been anticipated to become a very useful device that is lead-free, light, flexible, and easily processed, containing very fine tungsten powder at as much as 80% by weight. The purpose of this study was to investigate the dosimetric changes due to TFP shielding for electron beams. TFP (thickness 0-15mm) was placed on water or a water-equivalent phantom. Percentage depth ionization and transmission were measured for 4, 6, and 9MeV electron beams. Off-center ratio was also measured using film dosimetry at depth of dose maximum under similar conditions. Then, beam profiles and transmission with two shielding materials, TFP and lead, were evaluated. Reductions of 95% by using TFP at 0.5cm depth occurred at 4, 9, and 15mm with 4, 6, and 9MeV electron beams, respectively. It is found that the dose tend to increase at the field edge shaped with TFP, which might be influenced by the thickness. TFP has several unique features and is very promising as a useful tool for radiation protection for electron beams, among others.
Collapse
Affiliation(s)
- Takahiro Fujimoto
- Clinical Radiology Service Division, Kyoto University Hospital, Kyoto 606-8397, Japan
| | - Hajime Monzen
- Department of Radiation Oncology and Image-Applied Therapy, Kyoto University Graduate School of Medicine, 54 Kawara-cho, Shogoin, Sakyo-ku, Kyoto 606-8507, Japan.
| | - Manabu Nakata
- Clinical Radiology Service Division, Kyoto University Hospital, Kyoto 606-8397, Japan
| | - Takashi Okada
- Clinical Radiology Service Division, Kyoto University Hospital, Kyoto 606-8397, Japan
| | - Shinsuke Yano
- Clinical Radiology Service Division, Kyoto University Hospital, Kyoto 606-8397, Japan
| | - Toru Takakura
- Clinical Radiology Service Division, Kyoto University Hospital, Kyoto 606-8397, Japan
| | - Junichi Kuwahara
- Clinical Radiology Service Division, Kyoto University Hospital, Kyoto 606-8397, Japan
| | - Makoto Sasaki
- Clinical Radiology Service Division, Kyoto University Hospital, Kyoto 606-8397, Japan
| | - Kyoji Higashimura
- Clinical Radiology Service Division, Kyoto University Hospital, Kyoto 606-8397, Japan
| | - Masahiro Hiraoka
- Department of Radiation Oncology and Image-Applied Therapy, Kyoto University Graduate School of Medicine, 54 Kawara-cho, Shogoin, Sakyo-ku, Kyoto 606-8507, Japan
| |
Collapse
|
2
|
Srivastava SP, Cheng CW, Andrews J, Das IJ. Dose perturbation due to metallic breast expander in electron and photon beam treatment of breast cancer. ACTA ACUST UNITED AC 2013. [DOI: 10.1007/s13566-013-0109-4] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/25/2022]
|
3
|
Abstract
OBJECTIVES Low-energy electron beams are characterised by low surface doses with a pronounced dose build-up and penetration of several centimetres, but often a higher surface dose and a lower penetration range is desired. The purpose of this study was to investigate the use of an electron spoiler to modify these beams for treating surface skin diseases and evaluate the feasibility of this method. MATERIALS AND METHODS An aluminium foil 4-mm thick covering the end of the electron applicator was used as a spoiler for a 6 MeV electron beam. The dosimetric characteristics of this beam were measured, and Monte Carlo simulations were performed. RESULTS The spoiler reduced the practical range and increased surface and build-up doses, but it also significantly broadened the penumbra and increased peripheral doses. Nevertheless, the beam was clinically acceptable when skin collimation with lead was employed. Monte Carlo simulations agreed well with all the experimental measurements. CONCLUSIONS The feasibility of using a low-energy electron beam with a spoiler for treating surface skin diseases was demonstrated. The method is hygienic and avoids some of the disadvantages associated with the bolus technique, but it is valid only for flat surfaces and perpendicular incidence. As a consequence, it can be an alternative to bolus and other reported methods in certain cases, especially when a particular sterility assurance level is required.
Collapse
|
4
|
Currie BE. Determining superficial dosimetry for the internal canthus from the Monte Carlo simulation of kV photon and MeV electron beams. AUSTRALASIAN PHYSICAL & ENGINEERING SCIENCES IN MEDICINE 2009; 32:68-80. [PMID: 19623857 DOI: 10.1007/bf03178631] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 12/01/2022]
Abstract
This paper presents the findings of an investigation into the Monte Carlo simulation of superficial cancer treatments of an internal canthus site using both kilovoltage photons and megavoltage electrons. The EGSnrc system of codes for the Monte Carlo simulation of the transport of electrons and photons through a phantom representative of either a water phantom or treatment site in a patient is utilised. Two clinical treatment units are simulated: the Varian Medical Systems Clinac 2100C accelerator for 6 MeV electron fields and the Pantak Therapax SXT 150 X-ray unit for 100 kVp photon fields. Depth dose, profile and isodose curves for these simulated units are compared against those measured by ion chamber in a PTW Freiburg MP3 water phantom. Good agreement was achieved away from the surface of the phantom between simulated and measured data. Dose distributions are determined for both kV photon and MeV electron fields in the internal canthus site containing lead and tungsten shielding, rapidly sloping surfaces and different density interfaces. There is a relatively high level of deposition of dose in tissue-bone and tissue-cartilage interfaces in the kV photon fields in contrast to the MeV electron fields. This is reflected in the maximum doses in the PTV of the internal canthus field being 12 Gy for kV photons and 4.8 Gy for MeV electrons. From the dose distributions, DVH and dose comparators are used to assess the simulated treatment fields. Any indication as to which modality is preferable to treat the internal canthus requires careful consideration of many different factors, this investigation provides further perspective in being able to assess which modality is appropriate.
Collapse
Affiliation(s)
- B E Currie
- Department of Physics and Astronomy, University of Canterbury, Christchurch, New Zealand.
| |
Collapse
|
5
|
Abstract
For over 50 years, electron beams have been an important modality for providing an accurate dose of radiation to superficial cancers and disease and for limiting the dose to underlying normal tissues and structures. This review looks at many of the important contributions of physics and dosimetry to the development and utilization of electron beam therapy, including electron treatment machines, dose specification and calibration, dose measurement, electron transport calculations, treatment and treatment-planning tools, and clinical utilization, including special procedures. Also, future changes in the practice of electron therapy resulting from challenges to its utilization and from potential future technology are discussed.
Collapse
Affiliation(s)
- Kenneth R Hogstrom
- Department of Physics and Astronomy, Louisiana State University, Baton Rouge, LA 70803-4001, USA.
| | | |
Collapse
|
6
|
Chi PCM, Hogstrom KR, Starkschall G, Antolak JA, Boyd RA. Modeling skin collimation using the electron pencil beam redefinition algorithm. Med Phys 2005; 32:3409-18. [PMID: 16370427 DOI: 10.1118/1.2064808] [Citation(s) in RCA: 7] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/07/2022] Open
Abstract
Skin collimation is an important tool for electron beam therapy that is used to minimize the penumbra when treating near critical structures, at extended treatment distances, with bolus, or using arc therapy. It is usually made of lead or lead alloy material that conforms to and is placed on patient surface. Presently, commercially available treatment-planning systems lack the ability to model skin collimation and to accurately calculate dose in its presence. The purpose of the present work was to evaluate the use of the pencil beam redefinition algorithm (PBRA) in calculating dose in the presence of skin collimation. Skin collimation was incorporated into the PBRA by terminating the transport of electrons once they enter the skin collimator. Both fixed- and arced-beam dose calculations for arced-beam geometries were evaluated by comparing them with measured dose distributions for 10- and 15-MeV beams. Fixed-beam dose distributions were measured in water at 88-cm source-to-surface distance with an air gap of 32 cm. The 6 x 20-cm2 field (dimensions projected to isocenter) had a 10-mm thick lead collimator placed on the surface of the water with its edge 5 cm inside the field's edge located at +10 cm. Arced-beam dose distributions were measured in a 13.5-cm radius polystyrene circular phantom. The beam was arced 90 degrees (-45 degrees to +45 degrees), and 10-mm thick lead collimation was placed at +/- 30 degrees. For the fixed beam at 10 MeV, the PBRA- calculated dose agreed with measured dose to within 2.0-mm distance to agreement (DTA) in the regions of high-dose gradient and 2.0% in regions of low dose gradient. At 15 MeV, the PBRA agreed to within a 2.0-mm DTA in the regions of high-dose gradient; however, the PBRA underestimated the dose by as much as 5.3% over small regions at depths less than 2 cm because it did not model electrons scattered from the edge of the skin collimation. For arced beams at 10 MeV, the agreement was 1-mm DTA in the high-dose gradient regions, and 2% in the low-dose gradient regions. For arced beams at 15 MeV, the agreement was 1 mm in the high-dose gradient regions, and in the low-dose gradient region at depth less than 2 cm, as much as 5% dose difference was observed. This study demonstrated the ease with which skin collimation can be incorporated into the PBRA. The good agreement of PBRA calculated with measured dose shows that the PBRA is likely sufficiently accurate for clinical use in the presence of skin collimation for electron arc therapy. To further improve the accuracy of the PBRA in regions having significant electrons scattered from the edge of the skin collimation would require transporting the electrons through the lead skin collimation near its edges.
Collapse
Affiliation(s)
- Pai-Chun M Chi
- Department of Radiation Physics, The University of Texas M.D. Anderson Cancer Center, 1515 Holcombe Boulevard, Houston, Texas 77030, USA.
| | | | | | | | | |
Collapse
|
7
|
Das IJ, Cheng CW, Mitra RK, Kassaee A, Tochner Z, Solin LJ. Transmission and dose perturbations with high-Z materials in clinical electron beams. Med Phys 2004; 31:3213-21. [PMID: 15651605 DOI: 10.1118/1.1819551] [Citation(s) in RCA: 15] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/07/2022] Open
Abstract
High density and atomic number (Z) materials used in various prostheses, eye shielding, and beam modifiers produce dose enhancements on the backscatter side in electron beams and is well documented. However, on the transmission side the dose perturbation is given very little clinical importance, which is investigated in this study. A simple and accurate method for dose perturbation at metallic interfaces with soft tissues and transmission through these materials is required for all clinical electron beams. Measurements were taken with thin-window parallel plate ion chambers for various high-Z materials (Al, Ti, Cu, and Pb) on a Varian and a Siemens accelerator in the energy range of 5-20 MeV. The dose enhancement on both sides of the metallic sheet is due to increased electron fluence that is dependent on the beam energy and Z. On the transmission side, the magnitude of dose enhancement depends on the thickness of the high-Z material. With increasing thickness, dose perturbation reduces to the electron transmission. The thickness of material to reduce 100% (range of dose perturbation), 50% and 10% transmission is linear with the beam energy. The slope (mm/MeV) of the transmission curve varies exponentially with Z. A nonlinear regression expression (t=E[alpha+beta exp(-0.1Z)]) is derived to calculate the thickness at a given transmission, namely 100%, 50%, and 10% for electron energy, E, which is simple, accurate and well suited for a quick estimation in clinical use. Caution should be given to clinicians for the selection of thickness of high-Z materials when used to shield critical structures as small thickness increases dose significantly at interfaces.
Collapse
Affiliation(s)
- Indra J Das
- Department of Radiation Oncology, University of Pennsylvania, Philadelphia, Pennsylvania 19104, USA.
| | | | | | | | | | | |
Collapse
|
8
|
Perez MD, Hill RF, Whitaker MK, Greig L, West MP, Williams MJ, Holloway LC. Dosimetry of small electron fields shaped by lead. AUSTRALASIAN PHYSICAL & ENGINEERING SCIENCES IN MEDICINE 2004; 26:119-24. [PMID: 14626851 DOI: 10.1007/bf03178781] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 10/20/2022]
Abstract
Electron radiotherapy fields are commonly used to treat superficial cancers. Field shaping can be achieved by placing lead on the patient surface to minimise the dose to surrounding areas. However, significant dosimetry changes under high density material edges for electron fields have been reported in the literature. This project evaluated the dosimetry of small dimension electron fields shaped with lead placed on the surface. Comparisons were made between circular lead cutouts placed on the skin and low melting point alloy cutouts placed in an applicator. Depth doses, profiles and output factors were measured using a diode detector in a water phantom. Film was also used to determine surface dose delivered when the lead cutouts were placed on the surface. Minimal differences were observed between the different setups for the depth dose curves, although significant differences were seen in the penumbra and the surface doses. The penumbra is smaller for the lead cutouts placed on the surface, however, significant dose increases at the edge of the field were observed for larger fields and energies; this may result in undesirable clinical effects.
Collapse
Affiliation(s)
- M D Perez
- Department of Radiation Oncology, Liverpool Hospital, Liverpool, Australia
| | | | | | | | | | | | | |
Collapse
|
9
|
Abstract
Near interfaces between two different media exposed to high-energy electron beams substantial dose and fluence perturbations due to backscatter can be observed. In this work, dose and fluence perturbations were studied for 4-19 MeV electron beams at backscatter interfaces of polystyrene, graphite, water, aluminium and lead. Measurements of relative dose using an NPL-designed thin-window plane-parallel ion chamber and a Markus ion chamber were performed to determine the effect of different interface materials and thicknesses. Results of Monte Carlo simulations with the EGSnrc code, including models of the ion chambers, were found to be in excellent agreement with the measurements. The well-documented increasing dose perturbation with increasing effective atomic number of the backscatter material and decreasing electron beam energy was confirmed. Simulations in a simplified slab geometry showed that, despite the decrease of average electron energy with depth in water, the dose perturbations decrease with increasing depth of the interface in water for all the materials in the study. This was ascribed to the change of the electron angular distribution with depth which has a different effect in water and in the presence of a high-Z interface. Electron fluence perturbations near a lead/water interface were found to cause small differences in unrestricted mass collision stopping power ratios, water to air. Effects of bremsstrahlung photons, characteristic photons and positrons from the backscattering material were found to be insignificant for electron interface dosimetry. When comparing simulations using EGSnrc and the older version of the same code, EGS4, underestimations of the dose perturbation effects of up to 7% were found when using the latter code to simulate 4 MeV electrons irradiating a lead/water interface. It is concluded that EGSnrc is a highly suitable tool for electron interface dosimetry studies.
Collapse
Affiliation(s)
- Frank Verhaegen
- Medical Physics Department, McGill University, Montreal General Hospital, 1650 Cedar Avenue, Montreal, Québec, H3G1A4. Canada.
| |
Collapse
|
10
|
Yaparpalvi R, Fontenla DP, Beitler JJ. Improved dose homogeneity in scalp irradiation using a single set-up point and different energy electron beams. Br J Radiol 2002; 75:670-7. [PMID: 12153941 DOI: 10.1259/bjr.75.896.750670] [Citation(s) in RCA: 16] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/05/2022] Open
Abstract
Homogeneous irradiation of the entire or a large portion of the superficial scalp poses both technical and dosimetric challenges. Some techniques will irradiate too much of the underlying normal brain while other techniques are either complex and involve field matching problems or may require sophisticated linear accelerator (linac) add-ons such as intensity modulated radiation therapy (IMRT)/electron multileaf collimation. However, many radiotherapy facilities are not equipped with such treatment modalities. We propose a practical treatment technique that can be delivered with a standard linac capable of producing high energy electrons. The proposed technique offers a simple alternative for achieving results equivalent to IMRT. Dose homogeneity throughout the treatment volume is achieved by aiming different energy electron beams at differential areas of the treatment surface to achieve improved dosimetry and rapid treatment delivery, while using a single set-up point. We introduced this treatment technique at our institution to treat superficial cancers of the scalp and other irregular surfaces.
Collapse
Affiliation(s)
- R Yaparpalvi
- Department of Radiation Oncology, Montefiore Medical Center and the Albert Einstein College of Medicine, Bronx, New York, USA
| | | | | |
Collapse
|