The influence of fibril composition and dimension on the performance of paper gated oxide transistors

Transparent Structures for ZnO Thin Film Paper Transistors Fabricated by Pulsed Electron Beam Deposition

Thin film transistors on paper are increasingly in demand for emerging applications, such as flexible displays and sensors for wearable and disposable devices, making paper a promising substrate for green electronics and the circular economy. ZnO self-assembled thin film transistors on a paper substrate, also using paper as a gate dielectric, were fabricated by pulsed electron beam deposition (PED) at room temperature. These self-assembled ZnO thin film transistor source-channel-drain structures were obtained in a single deposition process using 200 and 300 µm metal wires as obstacles in the path of the ablation plasma. These transistors exhibited a memory effect, with two distinct states, "on" and "off", and with a field-effect mobility of about 25 cm2/Vs in both states. For the "on" state, a threshold voltage (Vth on = -1.75 V) and subthreshold swing (S = 1.1 V/decade) were determined, while, in the "off" state, Vth off = +1.8 V and S = 1.34 V/decade were obtained. A 1.6 μA maximum drain current was obtained in the "off" state, and 11.5 μA was obtained in the "on" state of the transistor. Due to ZnO's non-toxicity, such self-assembled transistors are promising as components for flexible, disposable smart labels and other various green paper-based electronics.

Titania Nanoparticle-Stimulated Ultralow Frequency Detection and High-Pass Filter Behavior of a Flexible Piezoelectric Nanogenerator: A Self-Sustaining Energy Harvester for Active Motion Tracking

A significant driving force for the fabrication of IoT-compatible smart health gear integrated with multifunctional sensors is the growing trend in fitness and the overall wellness of the human body. In this work, we present an autonomous motion and activity-sensing device based on the efficacious nucleation of the polar β-phase in an electroactive polymer. Representatively, we investigate the nucleating effect of TiO2 nanoparticles on weight-modulated PVDF-HFP films (PT-5, PT-10, and PT-15) and subsequently prototype a sensing device with the film that demonstrates superior β-phase nucleation. The PT-10 film, with an optimal polar β-phase, shows the highest remnant polarization (2Pr) and energy density of 0.36 μC/cm2 and 22.3 mJ/cm3, respectively, at 60 kV/cm. The films mimic a high pass filter at frequencies above 10 KHz with very low impedance and high ac conductivity values. The frequency-dependent impedance studies reveal an effective interfacial polarization between TiO2 nanoparticles and PVDF-HFP, explicitly observed in the low-frequency region. Consequently, the sensor fabricated with PT-10 as the sensing layer exhibits ultralow frequency detection (25 Hz) resulting from the blood flow muscle oxygenation. The device successfully senses voluntary joint movements of the human body and actively tracks a range of motions, from brisk walking to running. Additionally, through repetitive human finger-tapping motion, the nanogenerator lights up multiple light-emitting diodes in series and charges capacitors of varying magnitudes under 50 s. The real-time human motion sensing and movement tracking modalities of the sensor hold promise in the arena of smart wearables, sports biomechanics, and contact-based medical devices.

Alkali-Doped Nanopaper Membranes Applied as a Gate Dielectric in FETs and Logic Gates with an Enhanced Dynamic Response

The market for flexible, hybrid, and printed electronic systems, which can appear in everything from sensors and wearables to displays and lighting, is still uncertain. What is clear is that these systems are appearing every day, enabling devices and systems that can, in the near future, be crumpled up and tucked in our pockets. Within this context, cellulose-based modified nanopapers were developed to serve both as a physical support and a gate dielectric layer in field-effect transistors (FETs) that are fully recyclable. It was found that the impregnation of those nanopapers with sodium (Na⁺) ions allows for low operating voltage FETs (<3 V), with mobility above 10 cm² V^-1 s^-1, current modulation surpassing 10⁵, and an improved dynamic response. Thus, it was possible to implement those transistors into simple circuits such as inverters, reaching a clear discrimination between logic states. Besides the overall improvement in electrical performance, these devices have shown to be an interesting alternative for reliable, sustainable, and flexible electronics, maintaining proper operation even under stress conditions.

Paper-based field-effect transistor sensors

The present scenario in the world largely demands affordable, fast, recyclable, and flexible electronic devices for bio sensing. Varieties of paper-based devices such as microfluidics paper electrodes, paper diodes, and paper-based transistors etc. have been developed and validated. Most of the fabrication techniques published so far have focused on economic, environment-friendly straightforward methods to develop paper-based field-effect transistors (PFET) sensors, additionally, explored their applications. The synthetic-free, mechanically flexible, biocompatible, and signal amplification capability render PFET based sensors for wearable device makers. Modified organic/inorganic PFETs identify target analytes based on the electrical signal and endow them as perfect transducers. In the field of PFET bio sensing technology, numerous challenges are needed to be discussed to proceed forward in biomedical and other analytical applications. Realizing biologically or chemically modified PFET having an exceptional signal to noise ratio, specificity, with rapid detection ability is challenging. This review recapitulates the fabrication techniques, performances of various PFET sensors, and summarizes the report by concluding remarks including the limitations of the existing PFET based sensors and the future holds in regards to the sustainable nature of PFET.

Ionic Conductive Cellulose Mats by Solution Blow Spinning as Substrate and a Dielectric Interstrate Layer for Flexible Electronics

Renewable cellulose substrates with submicron- and nanoscale structures have revived interest in paper electronics. However, the processes behind their production are still complex and time- and energy-consuming. Besides, the weak electrolytic properties of cellulose with submicron- and nanoscale structures have hindered its application in transistors and integrated circuits with low-voltage operation. Here, we report a simple, low-cost approach to produce flexible ionic conductive cellulose mats using solution blow spinning, which are used both as dielectric interstrate and substrate in low-voltage devices. The electrochemical properties of the cellulose mats are tuned through infiltration with alkali hydroxides (LiOH, NaOH, or KOH), enabling their application as dielectric and substrate in flexible, low-voltage, oxide-based field-effect transistors and pencil-drawn resistor-loaded inverters. The transistors exhibit good transistor performances under operation voltage below 2.5 V, and their electrical performance is strictly related to the type of alkali ionic specie incorporated. Devices fabricated on K⁺-infiltrated cellulose mats present the best characteristics, indicating pure capacitive charging of the semiconductor. The pencil-drawn load resistor inverter presents good dynamic performance. These findings may pave the way for a new generation of low-power, wearable electronics, enabling concepts such as the "Internet of Things".

Preparation and properties of microfibrillated cellulose with different carboxyethyl content

Carboxyethyl reaction was used as a pretreatment method before grinding and homogenization to prepare microfibrillated cellulose (MFC). The effect of carboxyethylation on the properties of cellulose materials and prepared MFC samples were investigated. Results showed that cellulose materials with different carboxyethyl content were obtained by controlling the chemical dosage. This reaction increased the water retention value, decreased the degree of polymerization and crystallinity, and changed the crystalline structure of cellulose. After pretreatment, the cellulose fibers were easier to be swelled and fibrillated, which greatly reduces the frequency of grinding. In addition, the diameter of the produced MFC decreased with the increase of carboxyl content. The charge density, suspension stability and transparency of MFC increased obviously due to the presence of carboxyethyl groups. This study provides a comprehensive understanding of carboxyethyl pretreatment for the preparation of MFC, which may help to enrich and promote the preparation and application of MFC.

Fully Printed Zinc Oxide Electrolyte-Gated Transistors on Paper

Fully printed and flexible inorganic electrolyte gated transistors (EGTs) on paper with a channel layer based on an interconnected zinc oxide (ZnO) nanoparticle matrix are reported in this work. The required rheological properties and good layer formation after printing are obtained using an eco-friendly binder such as ethyl cellulose (EC) to disperse the ZnO nanoparticles. Fully printed devices on glass substrates using a composite solid polymer electrolyte as gate dielectric exhibit saturation mobility above 5 cm² V⁻¹ s⁻¹ after annealing at 350 °C. Proper optimization of the nanoparticle content in the ink allows for the formation of a ZnO channel layer at a maximum annealing temperature of 150 °C, compatible with paper substrates. These devices show low operation voltages, with a subthreshold slope of 0.21 V dec⁻¹, a turn on voltage of 1.90 V, a saturation mobility of 0.07 cm² V⁻¹ s⁻¹ and an I_on/I_off ratio of more than three orders of magnitude.

Trends in Advanced Functional Material Applications of Nanocellulose

The need to transition to more sustainable and renewable technology has resulted in a focus on cellulose nanofibrils (CNFs) and nanocrystals (CNCs) as one of the materials of the future with potential for replacing currently used synthetic materials. Its abundance and bio-derived source make it attractive and sought after as well. CNFs and CNCs are naturally hydrophilic due to the abundance of -OH group on their surface which makes them an excellent recipient for applications in the medical industry. However, the hydrophilicity is a deterrent to many other industries, subsequently limiting their application scope. In either light, the increased rate of progress using CNCs in advanced materials applications are well underway and is becoming applicable on an industrial scale. Therefore, this review explores the current modification platforms and processes of nanocellulose directly as functional materials and as carriers/substrates of other functional materials for advanced materials applications. Niche functional attributes such as superhydrophobicity, barrier, electrical, and antimicrobial properties are reviewed due to the focus and significance of such attributes in industrial applications.

Organic flash memory on various flexible substrates for foldable and disposable electronics

With the emergence of wearable or disposable electronics, there grows a demand for a flash memory realizable on various flexible substrates. Nevertheless, it has been challenging to develop a flash memory that simultaneously exhibits a significant level of flexibility and performance. This is mainly due to the scarcity of flexible dielectric materials with insulating properties sufficient for a flash memory, which involves dual dielectric layers, respectively, responsible for tunneling and blocking of charges. Here we report ultra-flexible organic flash memories based on polymer dielectrics prepared by initiated chemical vapor deposition. Using their near-ideal dielectric characteristics, we demonstrate flash memories bendable down to a radius of 300 μm that exhibits a relatively long-projected retention with a programming voltage on par with the present industrial standards. The proposed memory technology is then applied to non-conventional substrates, such as papers, to demonstrate its feasibility in a wide range of applications.

Flexible flash memory is crucial to modern electronics, but its fabrication is challenging in the absence of suitable dielectric materials. Here, Lee et al. realize organic memory with retention over 10 years using tunneling and blocking dielectric layers prepared by initiated chemical vapor deposition.

Room-Temperature Fabrication of High-Performance Amorphous In-Ga-Zn-O/Al2O3 Thin-Film Transistors on Ultrasmooth and Clear Nanopaper

Integrating biodegradable cellulose nanopaper into oxide thin-film transistors (TFTs) for next generation flexible and green flat panel displays has attracted great interest because it offers a viable solution to address the rapid increase of electronic waste that poses a growing ecological problem. However, a compromise between device performance and thermal annealing remains an obstacle for achieving high-performance nanopaper TFTs. In this study, a high-performance bottom-gate IGZO/Al₂O₃ TFT with a dual-layer channel structure was initially fabricated on a highly transparent, clear, and ultrasmooth nanopaper substrate via conventional physical vapor deposition approaches, without further thermal annealing processing. Purified nanofibrillated cellulose with a width of approximately 3.7 nm was used to prepare nanopaper with excellent optical properties (92% transparency, 0.85% transmission haze) and superior surface roughness (Rq is 1.8 nm over a 5 × 5 μm² scanning area). More significantly, a bilayer channel structure (IGZO/Al₂O₃) was adopted to fabricate high performance TFT on this nanopaper substrate without thermal annealing and the device exhibits a saturation mobility of 15.8 cm²/(Vs), an I_on/I_off ratio of 4.4 × 10⁵, a threshold voltage (V_th) of -0.42 V, and a subthreshold swing (SS) of 0.66 V/dec. The room-temperature fabrication of high-performance IGZO/Al₂O₃ TFTs on such nanopaper substrate without thermal annealing treatment brings industry a step closer to realizing inexpensive, flexible, lightweight, and green paper displays.

Office paper decorated with silver nanostars - an alternative cost effective platform for trace analyte detection by SERS

For analytical applications in portable sensors to be used in the point-of-need, low-cost SERS substrates using paper as a base, are an alternative. In this work, SERS substrates were produced on two different types of paper: a high porosity paper (Whatman no. 1); and a low porosity paper (commercially available office paper, Portucel Soporcel). Solutions containing spherical silver nanoparticles (AgNPs) and silver nanostars (AgNSs) were separately drop-casted on hydrophilic wells patterned on the papers. The porosity of the paper was found to play a determinant role on the AgNP and AgNS distribution along the paper fibres, with most of the nanoparticles being retained at the illuminated surface of the office paper substrate. The highest SERS enhancements were obtained for the office paper substrate, with deposited AgNSs. A limit of detection for rhodamine-6G as low as 11.4 ± 0.2 pg could be achieved, with an analytical enhancement factor of ≈10⁷ for this specific analyte. The well patterning technique allowed good signal uniformity (RSD of 1.7%). Besides, these SERS substrates remained stable after 5 weeks of storage (RSD of 7.3%). Paper-induced aggregation of AgNPs was found to be a viable alternative to the classical salt-induced aggregation, to obtain a highly sensitive SERS substrates.

Physically Transient Memory on a Rapidly Dissoluble Paper for Security Application

We report the transient memory device by means of a water soluble SSG (solid sodium with glycerine) paper. This material has a hydroscopic property hence it can be soluble in water. In terms of physical security of memory devices, prompt abrogation of a memory device which stored a large number of data is crucial when it is stolen because all of things have identified information in the memory device. By utilizing the SSG paper as a substrate, we fabricated a disposable resistive random access memory (RRAM) which has good data retention of longer than 106 seconds and cycling endurance of 300 cycles. This memory device is dissolved within 10 seconds thus it can never be recovered or replicated. By employing direct printing but not lithography technology to aim low cost and disposable applications, the memory capacity tends to be limited less than kilo-bits. However, unlike high memory capacity demand for consumer electronics, the proposed device is targeting for security applications. With this regards, the sub-kilobit memory capacity should find the applications such as one-time usable personal identification, authentication code storage, cryptography key, and smart delivery tag. This aspect is attractive for security and protection system against unauthorized accessibility.

Paper Thermoelectrics: Merging Nanotechnology with Naturally Abundant Fibrous Material

The development of paper-based sensors, antennas, and energy-harvesting devices can transform the way electronic devices are manufactured and used. Herein we describe an approach to fabricate paper thermoelectric generators for the first time by directly impregnating naturally abundant cellulose materials with p- or n-type colloidal semiconductor quantum dots. We investigate Seebeck coefficients and electrical conductivities as a function of temperature between 300 and 400 K as well as in-plane thermal conductivities using Angstrom's method. We further demonstrate equipment-free fabrication of flexible thermoelectric modules using p- and n-type paper strips. Leveraged by paper's inherently low thermal conductivity and high flexibility, these paper modules have the potential to efficiently utilize heat available in natural and man-made environments by maximizing the thermal contact to heat sources of arbitrary geometry.

Recent Progress on Cellulose-Based Electro-Active Paper, Its Hybrid Nanocomposites and Applications

We report on the recent progress and development of research into cellulose-based electro-active paper for bending actuators, bioelectronics devices, and electromechanical transducers. The cellulose electro-active paper is characterized in terms of its biodegradability, chirality, ample chemically modifying capacity, light weight, actuation capability, and ability to form hybrid nanocomposites. The mechanical, electrical, and chemical characterizations of the cellulose-based electro-active paper and its hybrid composites such as blends or coatings with synthetic polymers, biopolymers, carbon nanotubes, chitosan, and metal oxides, are explained. In addition, the integration of cellulose electro-active paper is highlighted to form various functional devices including but not limited to bending actuators, flexible speaker, strain sensors, energy harvesting transducers, biosensors, chemical sensors and transistors for electronic applications. The frontiers in cellulose paper devices are reviewed together with the strategies and perspectives of cellulose electro-active paper and cellulose nanocomposite research and applications.

Sweet substrate: a polysaccharide nanocomposite for conformal electronic decals

A conformal electronic decal based on a polysaccharide circuit board (PCB) is fabricated and characterized. The PCBs are laminates composed of bioderived sugars - nanocellulose and pullulan. The PCB and decal transfer are a bioactive material system for supporting electronic devices capable of conforming to bio-logical surfaces.

Stable low-voltage operation top-gate organic field-effect transistors on cellulose nanocrystal substrates

We report on the performance and the characterization of top-gate organic field-effect transistors (OFETs), comprising a bilayer gate dielectric of CYTOP/Al2O3 and a solution-processed semiconductor layer made of a blend of TIPS-pentacene:PTAA, fabricated on recyclable cellulose nanocrystal-glycerol (CNC/glycerol) substrates. These OFETs exhibit low operating voltage, low threshold voltage, an average field-effect mobility of 0.11 cm(2)/(V s), and good shelf and operational stability in ambient conditions. To improve the operational stability in ambient a passivation layer of Al2O3 is grown by atomic layer deposition (ALD) directly onto the CNC/glycerol substrates. This layer protects the organic semiconductor layer from moisture and other chemicals that can either permeate through or diffuse out of the substrate.

A miniaturized flexible antenna printed on a high dielectric constant nanopaper composite

A high-dielectric-constant and flexible cellulose nanopaper composite is prepared by mixing a small amount of silver nanowires with cellulose nanofibers. The nanopaper antenna is downsized by about a half when using the nanopaper substrate. The nanopaper antenna has potential in wearable wireless communication devices.

Solvothermal synthesis of gallium-indium-zinc-oxide nanoparticles for electrolyte-gated transistors

Solution-processed field-effect transistors are strategic building blocks when considering low-cost sustainable flexible electronics. Nevertheless, some challenges (e.g., processing temperature, reliability, reproducibility in large areas, and cost effectiveness) are requirements that must be surpassed in order to achieve high-performance transistors. The present work reports electrolyte-gated transistors using as channel layer gallium-indium-zinc-oxide nanoparticles produced by solvothermal synthesis combined with a solid-state electrolyte based on aqueous dispersions of vinyl acetate stabilized with cellulose derivatives, acrylic acid ester in styrene and lithium perchlorate. The devices fabricated using this approach display a ION/IOFF up to 1 × 10(6), threshold voltage (VTh) of 0.3-1.9 V, and mobility up to 1 cm(2)/(V s), as a function of gallium-indium-zinc-oxide ink formulation and two different annealing temperatures. These results validates the usage of electrolyte-gated transistors as a viable and promising alternative for nanoparticle based semiconductor devices as the electrolyte improves the interface and promotes a more efficient step coverage of the channel layer, reducing the operating voltage when compared with conventional dielectrics gating. Moreover, it is shown that by controlling the applied gate potential, the operation mechanism of the electrolyte-gated transistors can be modified from electric double layer to electrochemical doping.

Nanocrystalline cellulose applied simultaneously as the gate dielectric and the substrate in flexible field effect transistors

Cotton-based nanocrystalline cellulose (NCC), also known as nanopaper, one of the major sources of renewable materials, is a promising substrate and component for producing low cost fully recyclable flexible paper electronic devices and systems due to its properties (lightweight, stiffness, non-toxicity, transparency, low thermal expansion, gas impermeability and improved mechanical properties).Here, we have demonstrated for the first time a thin transparent nanopaper-based field effect transistor (FET) where NCC is simultaneously used as the substrate and as the gate dielectric layer in an 'interstrate' structure, since the device is built on both sides of the NCC films; while the active channel layer is based on oxide amorphous semiconductors, the gate electrode is based on a transparent conductive oxide.Such hybrid FETs present excellent operating characteristics such as high channel saturation mobility (>7 cm(2) V (-1) s(-1)), drain-source current on/off modulation ratio higher than 10(5), enhancement n-type operation and subthreshold gate voltage swing of 2.11 V/decade. The NCC film FET characteristics have been measured in air ambient conditions and present good stability, after two weeks of being processed, without any type of encapsulation or passivation layer. The results obtained are comparable to ones produced for conventional cellulose paper, marking this out as a promising approach for attaining high-performance disposable electronics such as paper displays, smart labels, smart packaging, RFID (radio-frequency identification) and point-of-care systems for self-analysis in bioscience applications, among others.