Enhanced performance of ZnO microballoon arrays for a triboelectric nanogenerator

Improvement of Thermal Stability of Charges in Polylactic Acid Electret Films for Biodegradable Electromechanical Sensors

Eco-friendly sensors fabricated from biocompatible and biodegradable materials are promising candidates for wearable and implantable electronics due to their environmental sustainability and biosafety. This article reports a fully biodegradable electromechanical sensor (FBES) utilizing a sandwich structure with macro ripple structured polylactic acid (PLA) electret films acting as sensitive layers and molybdenum (Mo) sheets serving as electrodes for a wearable device application. The stability of the space charge stored within the PLA film has been enhanced by introducing an internal cellular structure and improving the polarization process. A macro ripple structure of the PLA layer with higher deformation is a great guarantee for boosting the pressure sensitivity. The results indicate that inserting cell microstructures and optimizing the polarization process significantly improve the charge storage stability of PLA films by nearly 55%. This enhancement is attributed to several factors, including the extended charge drift path of the charges in cellular films, a synergy effect of surface charges, and "macroscopic" dipole charges distributed in the cells. The fabricated sensor achieves a high sensitivity of 1000 pC/kPa, a wide pressure detection range of 0.03-62.4 kPa, and satisfactory stability. Such sensors are not only sensitive to body movements but also to subtle physiological signals, satisfying the diverse needs of wearable healthcare. Importantly, all the composition materials of the sensor can be completely degraded after their service, aligning with the environmentally friendly principles of green development.

High-Performance Triboelectric Nanogenerator with Double-Side Patterned Surfaces Prepared by CO2 Laser for Human Motion Energy Harvesting

The triboelectric nanogenerator (TENG) has demonstrated exceptional efficiency in harvesting diverse forms of mechanical energy and converting it into electrical energy. This technology is particularly valuable for powering low-energy electronic devices and self-powered sensors. Most traditional TENGs use single-sided patterned friction pairs, which restrict their effective contact area and overall performance. Here, we propose a novel TENG that incorporates microwave patterned aluminum (MC-Al) foil and microcone structured polydimethylsiloxane (MC-PDMS). This innovative design utilizes two PMMA molds featuring identical micro-hole arrays ablated by a CO2 laser, making it both cost-effective and easy to fabricate. A novel room imprinting technique has been employed to create the micromorphology of aluminum (Al) foil using the PMMA mold with shallower micro-hole arrays. Compared to TENGs with flat friction layers and single-side-patterned friction layers, the double-side-patterned MW-MC-TENG demonstrates superior output performance due to increased cone deformation and contact area. The open-circuit voltage of the MW-MC-TENG can reach 141 V, while the short-circuit current can attain 71.5 μA, corresponding to a current density of 2.86 µA/cm2. The power density reaches 1.4 mW/cm2 when the resistance is 15 MΩ, and it can charge a 0.1 μF capacitor to 2.01 V in 2.28 s. In addition, the MW-MC-TENG can function as an insole device to harvest walking energy, power 11 LED bulbs, monitor step speed, and power a timer device. Therefore, the MW-MC-TENG has significant application potential in micro-wearable devices.

Self-powered TENG probe for scanning surface charge distribution

Triboelectric nanogenerators are remarkable devices that show great potential in harvesting energy from mechanical work and are generally used for sensing purposes. Here we report a novel method for the fabrication of ZnO microspheres and the formation of TENG based on ZnO/PDMS composite. The zinc oxide microspheres with needle decorated structure via thermal oxidation of metallic zinc was grown at 500 °C. The TENG was then fabricated using ZnO/PDMS composite with Au sputtered electrode. While PDMS is a good triboelectric material, its output power density is low. Embedding ZnO micro/nanostructures in PDMS increases the output power of PDMS-based TENG manifolds. ZnO with a high dielectric constant exhibits semiconductor properties as well as piezoelectric properties. This combines with the triboelectric properties of PDMS and gives a significant boost to the TENG performance. This composite structure is used for the fabrication of high output power density TENG using contact separation mode, where the power density of 27Wm-2was achieved. Consequently, a novel device application to detect surface charge density through the fabricated TENG is reported and the subsequent reconstruction of surface charge topology based on the detected surface charge density on large surfaces is presented. This technique may be used for the study of surface charge morphology, electrostatics, triboelectric constants, and various other material properties for characterization and application purposes.

Advances in Inorganic Nanomaterials for Triboelectric Nanogenerators

Triboelectric nanogenerators (TENGs) that utilize triboelectrification and electrostatic induction to convert mechanical energy to electricity have attracted increasing interest in the last 10 years. As a universal physical phenomenon, triboelectrification can occur between any two surfaces that experience physical contact and separation regardless of the type of material. For this reason, many materials, including both organic and inorganic materials, have been studied in TENGs with different purposes. Although organic polymers are mainly used as triboelectric materials in TENGs, the application of inorganic nanomaterials has also been intensively studied because of their unique dielectric, electric, piezoelectric, and optical properties, which can improve the performance of TENGs. A review of how inorganic nanomaterials are used in TENGs would help researchers gain an overview of the progress in this area. Here, we present a review to summarize how inorganic nanomaterials are utilized in TENGs based on the roles, types, and characteristics of the nanomaterials.

Small-Sized, Lightweight, and Flexible Triboelectric Nanogenerator Enhanced by PTFE/PDMS Nanocomposite Electret

The rapid development of flexible and wearable electronics calls for a sustainable solution of the power supply. In recent years, the energy-harvesting triboelectric nanogenerator (TENG) has attracted increasing attentions due to its sustainability, flexibility, and versatility. However, achieving both high electric output and flexibility at the same time remains to be a challenge. In this work, we reported a corona charging enhanced flexible triboelectric nanogenerator (EF-TENG) to harvest mechanical energy from human motions. The EF-TENG relied on the repeated contacts between a poly(tetrafluoroethylene)/poly(dimethylsiloxane) nanocomposite electret and a nanofibers/AgNWs electrode on arrayed silicone pyramids. When the EF-TENG (3.5 × 3.5 cm²) was pressed, the open-circuit voltage ( V_oc), the short-circuit current ( I_sc), and the power density could reach 275 V, 9.5 μA, and 802.31 mW/m², respectively. The V_oc of the EF-TENG was improved by 244% compared to the device of which the electret was not corona charged. Major factors that affected the electric output of the EF-TENG were discussed, including the height of the pyramids, the configuration of the pyramids array, and the properties of the electret nanocomposite. The EF-TENG only had an overall thickness of 1.3 mm and a weight of 1.7 g, making it especially suitable to be attached onto human body for harvesting mechanical energy from biomechanical motions.

A self-powered triboelectric nanosensor for detecting the corrosion state of magnesium treated by micro-arc oxidation

Triboelectric nanogenerators prepared by micro-arc-oxidation-treated magnesium were used as a sensor to detect the corrosion state of it in return.

High-performance optical projection controllable ZnO nanorod arrays for microweighing sensors

Optical microweighing sensors are an essential component of micro-force measurements in physical, chemical, and biological detection fields, although, their limited detection range (less than 15°) severely hinders their wide application. Such a limitation is mainly attributed to the essential restrictions of traditional light reflection and optical waveguide modes. Here, we report a high-performance optical microweighing sensor based on the synergistic effects of both a new optical projection mode and a ZnO nanorod array sensor. Ascribed to the unique configuration design of this sensing method, this optical microweighing sensor has a wide detection range (more than 80°) and a high sensitivity of 90 nA deg^-1, which is much larger than that of conventional microcantilever-based optical microweighing sensors. Furthermore, the location of the UV light source can be adjusted within a few millimeters, meaning that the microweighing sensor does not need repetitive optical calibration. More importantly, for low height and small incident angles of the UV light source, we can obtain highly sensitive microweighing properties on account of the highly sensitive ZnO nanorod array-based UV sensor. Therefore, this kind of large detection range, non-contact, and non-destructive microweighing sensor has potential applications in air quality monitoring and chemical and biological detection.

Optimization principles and the figure of merit for triboelectric generators

Energy harvesting with triboelectric nanogenerators is a burgeoning field, with a growing portfolio of creative application schemes attracting much interest. Although power generation capabilities and its optimization are one of the most important subjects, a satisfactory elemental model that illustrates the basic principles and sets the optimization guideline remains elusive. We use a simple model to clarify how the energy generation mechanism is electrostatic induction but with a time-varying character that makes the optimal matching for power generation more restrictive. By combining multiple parameters into dimensionless variables, we pinpoint the optimum condition with only two independent parameters, leading to predictions of the maximum limit of power density, which allows us to derive the triboelectric material and device figure of merit. We reveal the importance of optimizing device capacitance, not only load resistance, and minimizing the impact of parasitic capacitance. Optimized capacitances can lead to an overall increase in power density of more than 10 times.

Self-Powered Acceleration Sensor Based on Liquid Metal Triboelectric Nanogenerator for Vibration Monitoring

An acceleration sensor is an essential component of the vibration measurement, while the passivity and sensitivity are the pivotal features for its application. Here, we report a self-powered and highly sensitive acceleration sensor based on a triboelectric nanogenerator composed of a liquid metal mercury droplet (LMMD) and nanofiber-networked polyvinylidene fluoride (nn-PVDF) film. Due to the ultrahigh surface-to-volume ratio of nn-PVDF film and high surface tension, high mass density, high elastic as well as mechanical robustness of LMMD, the open-circuit voltage and short-circuit current reach up to 15.5 V and 300 nA at the acceleration of 60 m/s², respectively. The acceleration sensor has a wide detection range from 0 to 60 m/s² with a high sensitivity of 0.26 V·s/m². Also, the output voltage and current show a negligible decrease over 200,000 cycles, evidently presenting excellent stability. Moreover, a high-speed camera was employed to dynamically capture the motion state of the acceleration sensor for insight into the corresponding work mechanism. Finally, the acceleration sensor was demonstrated to measure the vibration of mechanical equipment and human motion in real time, which has potential applications in equipment vibration monitoring and troubleshooting.