Characterisation of flattening filter free (FFF) beam properties for initial beam set-up and routine QA, independent of flattened beams

Multicentric characterisation of lateral beam profiles generated by 6FFF beam of three 0.35 T MR-linac systems

BACKGROUND

The physical characterisation of FFF-beam profiles in the presence of a magnetic field requires a new standardization procedure and formulation.

PURPOSE

The aim of this multicentric experience is to propose new normalisation factors to allow for the calculation of standard parameters typical of flattened beams, such as dosimetric field size and penumbra, for a 6 MV FFF beam from an MR-linac.

METHODS

The measurements were carried out on three ViewRay-MRIdiansystems. An equal set of measurements was acquired using the same equipment. Transverse beam profiles were acquired at seven different depthsand for six beam dimensions.The inflection point was estimated as the position of the maximum of a Gaussian fit obtained from the first derivative of the profiles. The position of the minimum and maximum points of the second derivative of the above Gaussian described the fall-off region, and the external peaks of the third derivative were considered as the in-field and out-field points. The profile normalisation was determined by imposing a 55% dose level at the inflection point and the renormalisation factors were calculated.

RESULTS

The position of the inflection point, and the second and third derivatives peaks were analysed,and the renormalisation factors as a function of field size and depth were determined. The values of the unflatness and the slope have been calculated for different depths and field sizes.

CONCLUSION

This study represents the first multi-centric evaluation of the profiles on different low-field MR-Linac systems and theset of renormalisation parameters to analyse the FFF-beam on that system was effectively proposed.

A Simplified Approach for Determination of Inflection Points of Flattening Filter-Free Photon Beam Using In-House Developed Software and Derivation of Reference Levels

Aim

This article aimed to present the salient features of the in-house developed Java program for the determination of inflection point and dosimetric parameters of flattening filter-free (FFF) photon beam. Reference levels for the dosimetric parameters of the FFF photon beams were also presented.

Materials and Methods

Beam profiles of 6 MV FFF and 10 MV FFF photon beams for a collimator setting of 20 cm × 20 cm measured at 10 cm depth in an isocentric setup acquired from various institutions were analyzed using an in-house developed Java program and manual method. The values of reference dose value (RDV), field size, penumbra, and degree of un-flatness (defined as the lateral separation between 90% [X90%], 75% [X75%], and 60% [X60%] dose points on the profile) were calculated and compared. The reference values of field size, penumbra, and degree of un-flatness were also determined for Varian and Elekta medical electron linear accelerators (LINACs).

Results

The maximum differences for RDV determined using the Java method and manual method are 2.4% and 2.7% for 6 and 10 MV FFF photon beams, respectively. The maximum difference between the values of field size, penumbra, and degree of un-flatness determined using Java and manual methods is within 1.3 mm. The reference values of field size and penumbra for Varian LINACs are 19.94 ± 0.10 cm and 0.83 ± 0.08 cm (6 MV FFF) and 19.95 ± 0.10 cm and 0.83 ± 0.08 cm (10 MV FFF). Similarly, the reference values of field size and penumbra for Elekta LINACs are 20.02 ± 0.09 cm and 0.94 ± 0.12 cm (6 MV FFF) and 20.03 ± 0.11 cm and 0.97 ± 0.16 cm (10 MV FFF).

Conclusions

A software program was developed in Java for analyzing the beam profiles of FFF photon beams. The results of Java-derived values of dosimetric parameters of FFF photon beams were found in good agreement with the values determined using the manual method. The reference values of these parameters were also derived and quoted using a large cohort of the data.

Linac reported steering error insensitive to 6 MV FFF transverse beam position deviations

Clinically significant beam position deviations were observed for a 6 MV FFF beam during patient specific QA on an Elekta linear accelerator. There was no significant reported transverse steering error from the machine ion chamber, and routine linac QA practices, including cardinal angle Winston-Lutz test, did not identify the deviations. Subsequent investigation using an electronic portal imaging device (EPID) revealed clinically significant beam position deviations for small steering errors. This prompted investigation into further impact and possible solutions. Testing set-points were established by adjusting transverse steering current to achieve introduced 2 T steering errors. Tests at each set-point included scanning water tank profiles and EPID images. A proposed method for adjusting the 2 T error sensitivity was tested via adjusting the 2 T loop parameter such that a reported error corresponds to specific beam position deviations. The testing set-points resulted in positional deviations of greater than 3 mm for reported errors of less than 1. A new method for improving 2 T error sensitivity was implemented. This work has shown that existing vendor protocol for establishing beam steering error for 6 MV FFF beams can lead to beam position deviations without machine interlocks or significant reported steering errors. Thus, an alternative method of establishing steering error sensitivity based on positional deviations is presented.