DSP-based current source for electrical impedance tomography

ACT5 Electrical Impedance Tomography System

OBJECTIVE

This article introduces the Adaptive Current Tomograph 5 (ACT5) Electrical Impedance Tomography (EIT) system. ACT5 is a 32 electrode applied-current multiple-source EIT system that can display real-time images of conductivity and susceptivity at 27 frames per second. The adaptive current sources in ACT5 can apply fully programmable current patterns with frequencies varying from 5 kHz to 500 kHz. The system also displays real-time ECG readings during the EIT imaging process.

METHODS

The hardware and software design and specifications are presented, including the current source design, FPGA hardware, safety features, calibration, and shunt impedance measurement.

RESULTS

Images of conductivity and susceptivity are presented from ACT5 data collected on tank phantoms and a human subject illustrating the system's ability to provide real-time images of pulsatile perfusion and ECG traces.

SIGNIFICANCE

The portability, high signal-to-noise ratio, and flexibility of applied currents over a wide range of frequencies enable this instrument to be used to obtain useful human subject data with relative clinical ease.

Fast absolute 3D CGO-based electrical impedance tomography on experimental tank data

Objective.To present the first 3D CGO-based absolute EIT reconstructions from experimental tank data.Approach.CGO-based methods for absolute EIT imaging are compared to traditional TV regularized non-linear least squares reconstruction methods. Additional robustness testing is performed by considering incorrect modeling of domain shape.Main Results.The CGO-based methods are fast, and show strong robustness to incorrect domain modeling comparable to classic difference EIT imaging and fewer boundary artefacts than the TV regularized non-linear least squares reference reconstructions.Significance.This work is the first to demonstrate fully 3D CGO-based absolute EIT reconstruction on experimental data and also compares to TV-regularized absolute reconstruction. The speed (1-5 s) and quality of the reconstructions is encouraging for future work in absolute EIT.

Characteristics and topic trends on electrical impedance tomography hardware publications

Objective: Electrical impedance tomography (EIT) is a technique to measure electrical properties of tissue. With the progress of modern integrated circuits and microchips, EIT instrumentation becomes an active research area to improve all aspects of device performance. Plenty of studies on EIT hardware have been presented in prestigious journals. This study explores publications on EIT hardware to identify the developing hotspots and trends. Method: Publications covering EIT hardware on the Web of Science Core Collection (WoSCC) database from 1989 to 2021 were collected for bibliometric analysis. CiteSpace and VOS viewer were used to study the characteristics of the publications. Main results: A total of 592 publications were analyzed, showing that the number of annual publications steadily increased. China, England, and South Korea were the most prolific countries on EIT hardware publications with productive native institutions and authors. Research topics spread out in "bio-electrical impedance imaging", "hardware optimization", "algorithms" and "clinical applications" (e.g., tissue, lung, brain, and oncology). Hardware research in "pulmonary" and "hemodynamic" applications focused on monitoring and were represented by silhouette recognition and dynamic imaging while research in "tumor and tissue" and "brain" applications focused on diagnosis and were represented by optimization of precision. Electrode development was a research focus through the years. Imaging precision and bioavailability of hardware optimization may be the future trend. Conclusion: Overall, system performance, particularly in the areas of system bandwidth and precision in applications may be the future directions of hardware research.

A Modified Howland Current Source Design for Simultaneous EIT/ECG Data Acquisition

The current source is one of the most critical circuits in electrical impedance tomography (EIT) hardware systems. The simplicity and excellent performance of the Howland current source makes it a prime candidate for this role in EIT systems. Although the Howland source and its family may be the best option for the high-frequency EIT operation, its low frequency noise may also limit the implementation of a system to simultaneously collect electrocardiogram (ECG) and EIT signals from the electrodes. This paper proposes modifications to the conventional Howland source to make is suitable for simultaneous EIT and ECG. The preliminary experimental results of this modified Howland show significant improvement in the collected ECG signal quality in the presence of the EIT signal.

Practical Implementation of a Novel Output Impedance Measurement Technique for EIT System While Attached to a Load. ANNUAL INTERNATIONAL CONFERENCE OF THE IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. ANNUAL INTERNATIONAL CONFERENCE 2021;2021:3952-3956. [PMID: 34892096 PMCID: PMC9310546 DOI: 10.1109/embc46164.2021.9629839] [Citation(s) in RCA: 0] [Impact Index Per Article: 0]

A novel method for measuring the output impedance of current sources in an EIT system is implemented and tested. The paper shows that the proposed method can be used at the time of operation while the load is attached to the EIT system. the results also show that performance of the system improves when the shunt impedance values from the proposed technique are used to set the adaptive sources as opposed to the shunt impedance values acquired through open circuit measurements.

Bandwidth and Common Mode Optimization for Current and Voltage Sources in Bioimpedance Spectroscopy

Bioimpedance measurements use current or voltage sources to inject an excitation signal into the body. These sources require a high bandwidth, typically from 1 kHz to 1 MHz. Besides a low common mode, current limitation is necessary for patient safety. In this paper, we compare a symmetric enhanced Howland current source (EHCS) and a symmetric voltage source (VS) based on a non-inverting amplifier between 1 kHz and 1 MHz. A common mode reduction circuit has been implemented in both sources. The bandwidth of each source was optimized in simulations and achieved a stable output impedance over the whole frequency range. In laboratory measurements, the output impedance of the EHCS had its -3 dB point at 400 kHz. In contrast, the VS reached the +3 dB point at 600 kHz. On average over the observed frequency range, the active common mode compensation achieved a common mode rejection of -57.7 dB and -71.8 dB for the EHCS and VS, respectively. Our modifications to classical EHCS and VS circuits achieved a low common mode signal between 1 kHz and 1 MHz without the addition of complex circuitry, like general impedance converters. As a conclusion we found VSs to be superior to EHCSs for bioimpedance spectroscopy due to the higher bandwidth performance. However, this only applies if the injected current of the VS can be measured.

Measuring Current Source Output Impedance in EIT Systems while Attached to a Load

A novel method for measuring the shunt impedance of current sources in Electrical Impedance Tomography (EIT) systems is introduced. In an EIT system, electrical currents with theoretical sum of zero, are applied to the body and any mismatch between the currents results in current going through an extra grounded electrode. Since the N - 1 current patterns applied in an N-electrode EIT system are orthogonal to each other, by introducing an additional linearly- independent current pattern, a system of linear equations can be established from which the unknown shunt impedances can be calculated. The framework of the proposed scheme is introduced and its effectiveness is validated through both simulation and practical implementation. The experimental results show that by measuring the shunt impedances with the proposed method and using those values to adjust the current sources, the current passing through the grounded electrode is significantly reduced.

Performance of an Adaptive Current Source for EIT Driving Loads through a Shielded Coaxial Cable

In Electrical Impedance Tomography (EIT) the coaxial cables used to connect the electrodes to the electronics have long been a concern due to their impact on system performance. Driving the shield of the cable is useful, since it mitigates the shunt capacitance. However, this approach introduces complexity and, sometimes, stability issues. Using "active electrodes", i.e. placing the front end of the electronics at the electrode end of the cables, is also helpful but can introduce packaging and hygiene problems. In this paper, a new type of high-precision current source is described and its performance is studied when driving loads through a coaxial cable. This new current source adjusts its current output to compensate for current lost in any shunt impedance to ground, including the shunt losses in the cable. Experimental results for frequencies up to 1 MHz are provided, comparing performance with resistive and complex loads connected without a cable, with 1 m of RG-174 coaxial cable with a driven shield, and 1 m of RG-174 coaxial cable with a grounded shield. The results for all 3 cases are similar, demonstrating that the source can provide satisfactory performance with a grounded-shield cable.