Real-time volumetric scintillation dosimetry

Second window near-infrared dosimeter (NIR2D) system for radiation dosimetry

Fiber-coupled scintillation dosimeters are a cost-effective alternative to the conventional ion chambers in radiation dosimetry. However, stem effects from optical fibers such as Cerenkov radiation incur significant errors in the readout signal. Here we introduce a second near-infrared window dosimeter, dubbed as NIR2D, that can potentially be used as real-time radiation detector for clinical megavoltage beams. Lanthanide-based rare-earth NaYF₄ nano-phosphors doped with both erbium and cerium elements were synthesized, and a compact 3D printed reader device integrated with a photodetector and data acquisition system was designed. The performance of the NIR2D was tested using a pre-clinical orthovoltage radiation source and a clinical megavoltage radiation source. The system was tested for dose linearity (100, 200, 600 MU), dose rate dependency (100, 200, 400, 600 MU min^-1), and energy dependency (6, 10, 15 MV). Test results with the clinical linear accelerator demonstrated excellent dose linearity and dose rate independency when exposed to 6 MV linac beams-both data follows a linear trendline with R² > 0.99. On the other hand, the NIR2D was energy dependent, where the readout dropped by 9% between 6 and 15 MV. For stem effects, we observed a finite Cerenkov contribution of 1%-3% when exposed between 100-600 MU min^-1 (6 MV) and 3%-6% when exposed between 5-15 MV (600 MU min^-1). While the stem effects were still observable, we expect that enhancing the current optical setup will simultaneously improve the scintillation signal and reduce the stem effects.

Simulating imaging-based tomographic systems using optical design software for resolving 3D structures of translucent media

Imaging-based tomography is emerging as the technique of choice for resolving 3D structures of translucent media, in particular for applications in external beam radiation therapy and combustion diagnostics. However, designing experimental prototypes is time-consuming and costly, and is carried out without the certainty of the imaging optics being optimal. In this paper, we present an optical-design-software-based method that enables end-to-end simulation imaging-based tomography systems. The method, developed using the real ray tracing features of Zemax OpticStudio, was validated in the context of 3D scintillation dosimetry, where multiple imaging systems are used to image the 3D light pattern emitted within an irradiated cubic plastic scintillator volume. The flexibility of the workflow enabled the assessment and comparison of the tomographic performance of standard and focused plenoptic cameras for the reconstruction of a clinical radiation dose distribution. The versatility of the proposed method offers the potential to ease the developmental and optimization process of imaging systems used in volumetric emission computed tomography applications.

Characterization of a plastic scintillating detector for the Small Animal Radiation Research Platform (SARRP)

PURPOSE

The purpose of this study was to characterize a small plastic scintillator developed for high resolution, real-time dosimetry of therapy and imaging x-ray beams delivered by an image-guided small animal irradiator.

MATERIALS AND METHODS

A 1 mm diameter, 1 mm long polystyrene BCF-60 scintillating fiber dosimeter was characterized with 220 kVp therapy and 40, 50, 60, 70, and 80 kVp imaging beams on the Small Animal Research Platform (SARRP). Scintillator output, sensitivity (charge per unit dose), linearity, and 0.2-mm resolution beam profile measurements were performed. A validated in-house Monte Carlo (MC) model of the SARRP was used to compute detailed energy spectra at locations of dosimetry, and validated scintillator measurement with MC simulations. Mass energy-absorption coefficients from the National Institute of Standards and Technology (NIST) tables convolved with MC-derived spectra were used in conjunction with Birks ionization quenching factors to correct scintillator output. An air kerma calibration method was employed to correct scintillator output for in-air beam profile measurements with open, 5 × 5, and 3 × 3 mm² square field sizes, and compared to MC simulations.

RESULTS

Scintillator dose response showed excellent linearity (R²  ≥ 0.999) for all sensitivity measurements, including output as a function of tube current. Detector sensitivity was 2.41 μC Gy^-1 for the 220 kVp therapy beam, and it ranged from 1.21 to 1.32 μC Gy^-1 for the 40-80 imaging beams. Percentage difference in sensitivity between the therapy and imaging beams before sensitivity correction and after using the Birks quenching factors were 52.3% and 10.2%, respectively. Percentage differences between the therapy and imaging beam sensitivities after using the air kerma calibration method for in-air measurements was excellent and below 0.3%. In-air beam profile measurements agreed to MC simulations within a mean difference of 2.4% for the 5 × 5 and 3 × 3 mm² field sizes, however, the scintillator showed signs of volume averaging at the penumbra edges.

CONCLUSIONS

A small plastic scintillator was characterized for therapy and imaging energies of a small animal irradiator, with output corrected for using an in-house MC model of the irradiator. The characterization of the scintillator detector system for small fields presents steps toward implementing real-time measurements for quality assurance and small animal treatment and imaging dose verification.

Determination of the Range and Spread-Out Bragg Peak Width of Proton Beams Using a Large-Volume Liquid Scintillator

Purpose

To determine the range, spread-out Bragg peak (SOBP) width, and output of a passive-scattering proton beam with a liquid scintillator detector, without the need for quenching correction.

Materials and Methods

The depth-light profiles of 3 beam energies (140, 160, and 180 MeV) with 6 SOBP widths at each energy, produced in a 20 × 20 × 20-cm³ liquid scintillator tank, were collected by a charge-coupled device camera. By defining landmarks on the light signals, measured ranges and SOBP widths were acquired. A linear dependence was found between nominal and measured properties, and calibration factors were obtained by comparing those properties. The daily output stability and reproducibility of the liquid scintillator detector were studied by conducting 8 repeated measurements over 2 weeks in a ⁶⁰Co beam.

Results

The beam ranges were determined with submillimeter accuracy without the need for any correction. The maximum difference between the measured and nominal range was 1.0 mm. The mean difference between the measured and nominal SOBP widths after correction was 0.1 mm (σ = 1.8 mm), with a maximum difference of 3.5 mm. The light output was reproducible with an SD of 0.14%.

Conclusions

The method described here makes it possible to quickly and accurately determine the range and SOBP width of a passive-scattering proton beam in a liquid scintillator, without the need for quenching correction. In addition, the detector proved to be reliable over time, showing good output consistency with a high degree of precision.