Laser post-processing of halide perovskites for enhanced photoluminescence and absorbance

On the efficiency of perovskite solar cells with a back reflector: effect of a hole transport material

Organometal halide perovskites are promising, high-performance absorbers in solar cells. However, the light-harvesting performance of these devices is still limited by excessive charge carrier recombination. Charge carrier management can be improved, taking into account the transport properties of layers surrounding the absorber. In particular, the choice of an appropriate hole-transport material (HTM) could provide a path towards increasing the device performance of perovskite solar cells (PSCs). The Lambertian reflection on the cell's back-surface reflector could increase the power conversion efficiency (PCE) of PSCs as well. Taking into account these facts, we analyse the absorptance and the PCE of a perovskite thin-film solar cell with the Lambertian reflection on the cell's back-surface reflector for various organic and inorganic HTMs. The analysis is done by means of the Monte-Carlo ray tracing simulations complemented by the transfer-matrix method to account for the interference phenomenon in the local generation rate G of carriers in a thin-film multilayer system. This function is employed further in the transport equations to calculate the current-voltage characteristics of the cell. We show that wide band gap HTMs, that possess negligible absorption, increase the photocurrent in the perovskite, passing reflected photons from the back reflector. In contrast, at the same perovskite thickness the PSC gains less photocurrent with narrow band gap HTMs, where an excessive non-radiative recombination takes place. Our analysis demonstrates that the optimal thickness of the solar cell with the typical absorber CH₃NH₃PbI₃ is ∼300 nm, providing the maximal efficiency ∼18.8% for the wide band gap HTM (CuSCN) at the moderate absorber purity (the diffusion length _D ∼ 1 μm).

Precise Tuning of the Thickness and Optical Properties of Highly Stable 2D Organometal Halide Perovskite Nanosheets through a Solvothermal Process and Their Applications as a White LED and a Fast Photodetector

Precise control of the thickness of large-area two-dimensional (2D) organometal halide perovskite layers is extremely challenging owing to the inherent instability of the organic component. Herein, a novel, highly reproducible, and facile solvothermal route is reported to synthesize and tailor the thickness and optical band gap of the organic-inorganic halide perovskite nanosheets (NSs). Our study reveals that self-assembly of randomly oriented perovskite nanorods leads to the growth of multilayered perovskite NSs at ∼100 °C, while at higher temperature, large-area few-layer to bilayer 2D NSs (CH₃NH₃PbBr₃) are obtained through lattice expansion and layer separation depending precisely on the temperature. Interestingly, the thickness of the 2D NSs shows a linear dependence on the reaction temperature and thus enables precise tuning of the thickness from 14 layers to 2 layers, giving rise to a systematic increase in the band gap and appearance of excitonic absorption bands. Quantitative analysis of the change in the band gap with thickness revealed a strong quantum confinement effect in the 2D layers. The perovskite 2D NSs exhibit tunable color and a high photoluminescence (PL) quantum yield (QY) up to 84%. Through a careful analysis of the steady-state and time-resolved PL spectra, the origin of the lower PL QY in thinner NSs is traced to surface defects in the 2D layers, for the first time. A white light converter was fabricated using the composition-tuned 2D CH₃NH₃PbBrI₂ NS on a blue light-emitting diode chip. The 2D perovskite photodetector exhibits a stable and very fast rise/fall time (24 μs/103 μs) along with high responsivity and detectivity of ∼1.93 A/W and 1.04 × 10¹² Jones, respectively. Storage, operational, and temperature-dependent stability studies reveal high stability of the 2D perovskite NSs under the ambient condition with high humidity. The reported method is highly promising for the development of large-area stable 2D perovskite layers for various cutting-edge optoelectronic applications.