Flow visualization and force measurement of the clapping effect in bio-inspired flying robots

Thrust enhancement and degradation mechanisms due to self-induced vibrations in bio-inspired flying robots

Bio-inspired flying robots (BIFRs) which fly by flapping their wings experience continuously oscillating aerodynamic forces. These oscillations in the driving force cause vibrations in the motion of the body around the mean trajectory. In other words, a hovering BIFR does not remain fixed in space; instead, it undergoes oscillatory motion in almost all directions around the stationary point. These oscillations affect the aerodynamic performance of the flier. Assessing the effect of these oscillations, particularly on thrust generation in two-winged and four-winged BIFRs, is the main objective of this work. To achieve such a goal, two experimental setups were considered to measure the average thrust for the two BIFRs. The average thrust is measured over the flapping cycle of the BIFRs. In the first experimental setup, the BIFR is installed at the end of a pendulum rod, in place of the pendulum mass. While flapping, the model creates a thrust force that raises the model along the circular trajectory of the pendulum mass to a certain angular position, which is an equilibrium point and is also stable. Measuring the weight of the BIFR and the equilibrium angle it obtains, it is straightforward to estimate the average thrust, by moment balance about the pendulum hinge. This pendulum setup allows the BIFR model to freely oscillate back and forth along the circular trajectory about the equilibrium position. As such, the estimated average thrust includes the effects of these self-induced vibrations. In contrast, we use another setup with a load cell to measure thrust where the model is completely fixed. The thrust measurement revealed that the load cell or the fixed test leads to a higher thrust than the pendulum or the oscillatory test for the two-winged model, showing the opposite behavior for the four-winged model. That is, self-induced vibrations have different effects on the two BIFR models. We felt that this observation is worth further investigation. It is important to mention that aerodynamic mechanisms for thrust generation in the two and four-winged models are different. A two-winged BIFR generates thrust through traditional flapping mechanisms whereas a four-winged model enjoys a clapping effect, which results from wing-wing interaction. In the present work, we use a motion capture system, aerodynamic modeling, and flow visualization to study the underlying physics of the observed different behaviors of the two flapping models. The study revealed that the interaction of the vortices with the flapping wing robots may play a role in the observed aerodynamic behavior of the two BIFRs.

Effect of incorporating wing veins on soft wings for flapping micro air vehicles

Small insects with flapping wings, such as bees and flies, have flexible wings with veins, and their compliant motion enhances flight efficiency and robustness. This study investigated the effects of integrating wing veins into soft wings for micro-flapping aerial vehicles. Prototypes of soft wings, featuring various wing areas and vein patterns in both the wing-chord and wing-span directions, were fabricated and evaluated to determine the force generated through flapping. The results indicated that the force is not solely dependent upon the wing area and is influenced by the wing vein pattern. Wings incorporating wing-chord veins produced more force compared to those with wing-span veins. In contrast, when the wing area was the specific wing area, wings with crossed wing veins, comprising both wing-span veins and wing-chord veins, produced more force. Although wing-chord veins tended to exert more influence on the force generated than the wing-span veins, the findings suggested that a combination of wing-span and wing-chord veins may be requisite, depending upon the wing area.

Review of insect-inspired wing micro air vehicle

Micro air vehicles (MAVs) have wide application prospects in environmental monitoring, disaster rescue and other civil fields because of their flexibility and maneuverability. Compared with fixed wing and rotary wing aircraft, flapping wing micro air vehicles (FWMAVs) have higher energy utilization efficiency and lower cost and have attracted extensive attention from scientists. Insects have become excellent bionic objects for the study of FWMAVs due to their characteristics of low Reynolds number, low noise, hoverability, small size and light weight. By mimicking flying insects, it may be possible to create highly efficient biomimetic FWMAVs. In this paper, insect flight aerodynamics are reviewed, and the mechanism designs of insect-inspired FWMAVs and their aerodynamics are summarized, including the wing type effect, vibration characteristics and aerodynamic characteristics of the flapping wing.

Dynamic experimental rigs for investigation of insect wing aerodynamics

This paper provides a systematic and critical review of dynamic experimental rigs used for insect wing aerodynamics research. The goal is to facilitate meaningful comparison of data from existing rigs and provide insights for designers of new rigs. The scope extends from simple one degree of freedom rotary rigs to multi degrees of freedom rigs allowing various rotation and translation motions. Experimental methods are characterized using a consistent set of parameters that allows objective comparison of different approaches. A comprehensive catalogue is presented for the tested flow conditions (assessed through Reynolds number, Rossby number and advance ratio), wing morphologies (assessed through aspect ratio, planform shape and thickness to mean chord ratio) and kinematics (assessed through motion degrees of freedom). Links are made between the type of aerodynamic characteristics being studied and the type of experimental set-up used. Rig mechanical design considerations are assessed, and the aerodynamic measurements obtained from these rigs are discussed.