Optimal phosphotungstinate concentration for polypyrrole linear actuation and energy storage

Alkali Metal Ion Insertion in Polypyrrole Polyoxometalates for Multifunctional Actuator-Sensor-Energy Storage Devices

Modern research technology's goal is to produce multifunctional materials that require low energy. In this work, we have applied polypyrrole (PPy) doped with dodecyl benzenesulfonate (DBS-) with the addition of polyoxometalates (POM) such as phosphotungstic acid (PTA) forming PPyDBS-PT composites. Two different PTA concentrations (4 mM and 8 mM) were used to form PPyDBS-PT4 and PPyDBS-PT8. The higher concentration of PTA created a highly dense and compact film which can be observed from scanning electron microscopy (SEM cross-section image), and also contains fewer phosphotungstate anions (PT3-) inclusion (via energy-dispersive X-ray spectroscopy, EDX). Three different aqueous electrolytes, LiCl (lithium chloride), NaCl (sodium chloride), and KCl (potassium chloride), were applied to investigate how those alkali metal ions perform as typical cation-driven actuators. Cyclic voltammetry with linear actuation revealed the tendency LiCl > NaCl > KCl in view of better strain, charge density, electronic conductivity, and Young's modulus of PPyDBS-PT4 outperformed PPyDBS-PT8. Chronopotentiometric measurements showed high specific capacitance for PPyDBS-PT4 at 260.6 ± 21 F g-1 with capacity retention after 5000 cycles of 88.5%. The sensor calibration of PPyDBS-PT4 revealed that the alkali cations (Li+, Na+, and K+) can be differentiated from each other. The PPyDBS-PT4 has multifunctional applications such as actuators, sensors, and energy storage.

Polypyrrole with Embedded Carbide-Derived Carbon with and without Phosphor Tungsten Acid: Linear Actuation and Energy Storage

Researchers have focused on incorporating porous carbon particles such as carbon-derived carbon (CDC) into polypyrrole (PPy), preferably on the surface, to achieve high-capacitive electrodes. Less attention is afforded to their linear actuation properties. Therefore, in this work, we chose two different electropolymerization processes using the typical PPy doped with dodecylbenzene sulfonate (DBS⁻) and added CDC particles, compared with CDC with phosphotungstic acid (PTA), forming CDC-PT⁴⁻ dopants. The resulting PPy/DBS-CDC (PPyCDC) and PPy/DBS-CDC-PT (PPyCDC-PT) films showed different morphologies, with PPyCDC having the most CDC particles on the surface with less surrounding PPy, while in PPyCDC-PT, all the CDC particles were covered with PPy. Their linear actuation properties, applying electrochemical techniques (cyclic voltammetry and square wave potential steps), were found to enhance the PPyCDC-PT films in organic (2-times-higher strain) and aqueous electrolytes (2.8-times-higher strain) in an applied potential range of 0.8 V to −0.5 V. The energy storage capability found for the PPyCDC was favorable, with 159 ± 13 F cm⁻³ (1.2 times lower for PPyCDC-PT) in the organic electrolyte, while in the aqueous electrolyte, a result of 135 ± 11 F cm⁻³ was determined (1.8 times lower for PPyCDC-PT). The results showed that PPyCDC was more favorable in terms of energy storage, while PPyCDC-PT was suitable for linear actuator applications. The characterization of both the film samples included scanning electron microscopy (SEM), Raman, FTIR, and energy-dispersive X-ray (EDX) spectroscopy.

Role of Polyoxometalate Contents in Polypyrrole: Linear Actuation and Energy Storage

A combination of polyoxometalates with polypyrrole is introduced in this work. Our goal was to include phosphotungstic acid (PTA) in different molar concentrations (0.005, 0.01, and 0.05 M) in the electropolymerization of pyrrole doped with dodecylbenzene sulfonate (DBS) and phosphotungstinates (PT), forming PPy/DBS-PT films. Scanning electron microscopy (SEM) revealed that the PPy/DBS-PT films became denser and more compact with increasing PTA concentrations. The incorporation of PT in PPy/DBS was analyzed using Fourier-transform infrared (FTIR) and energy dispersive X-ray (EDX) spectroscopy. The linear actuation in cyclic voltammetry and potential square wave steps in an organic electrolyte revealed increasing mixed actuation, with major expansion upon oxidation found for PPy/DBS-PT films with a PTA concentration of 0.005 M. Best results of a strain of 12.8% and stress at 0.68 MPa were obtained for PPy/DBS-PT (0.01 M). The PPy/DBS-PT films polymerized in the presence of 0.05 M of PTA and showed main expansion upon reduction, changing the actuation direction. Chronopotentiometric measurements of PPy/DBS-PT samples were conducted to determine the specific capacitance optimal for a 0.01 M PTA concentration in the range of 80 F g⁻¹ (±0.22 A g⁻¹).

Polypyrrole with Phosphor Tungsten Acid and Carbide-Derived Carbon: Change of Solvent in Electropolymerization and Linear Actuation

Linear actuators based on polypyrrole (PPy) are envisaged to have only one ion that triggers the actuation direction, either at oxidation (anion-driven) or at reduction (cation-driven). PPy doped with dodecylbenzenesulfonate (PPy/DBS) is the most common applied conducting polymer having cation-driven actuation in aqueous solvent and mainly anion-driven actuation in an organic electrolyte. It is somehow desired to have an actuator that is independent of the applied solvent in the same actuation direction. In this research we made PPy/DBS with the addition of phosphorus tungsten acid, forming PPyPT films, as well with included carbide derived carbon (CDC) resulting in PPyCDC films. The solvent in electropolymerization was changed from an aqueous ethylene glycol mixture to pure EG forming PPyPT-EG and PPyCDC-EG composites. Our goal in this study was to investigate the linear actuation properties of PPy composites applying sodium perchlorate in aqueous (NaClO₄-aq) and propylene carbonate (NaClO₄-PC) electrolytes. Cyclic voltammetry and square potential steps in combination with electro-chemo-mechanical-deformation (ECMD) measurements of PPy composite films were performed. The PPyPT and PPyCDC had mixed ion-actuation in NaClO₄-PC while in NaClO4-aq expansion at reduction (cation-driven) was observed. Those novel PPy composites electropolymerized in EG solvent showed independently which solvent applied mainly expansion at reduction (cation-driven actuator). Chronopotentiometric measurements were performed on all composites, revealing excellent specific capacitance up to 190 F g^-1 for PPyCDC-EG (best capacitance retention of 90 % after 1000 cycles) and 130 F g^-1 for PPyPT-EG in aqueous electrolyte. The films were characterized by scanning electron microscopy (SEM), Raman, Fourier-transform infrared (FTIR) and energy dispersive X-ray spectroscopy (EDX).

Multifunctionality of Polypyrrole Polyethyleneoxide Composites: Concurrent Sensing, Actuation and Energy Storage

In films of conducting polymers, the electrochemical reaction(s) drive the simultaneous variation of different material properties (reaction multifunctionality). Here, we present a parallel study of actuation-sensing-energy storage triple functionality of polypyrrole (PPy) blends with dodecylbenzenesulfonate (DBS-), PPy/DBS, without and with inclusion of polyethyleneoxide, PPy-PEO/DBS. The characterization of the response of both materials in aqueous solutions of four different salts indicated that all of the actuating, sensing and charge storage responses were, independent of the electrolyte, present for both materials, but stronger for the PPy-PEO/DBS films: 1.4× higher strains, 1.3× higher specific charge densities, 2.5× higher specific capacitances and increased ion-sensitivity towards the studied counterions. For both materials, the reaction energy, the material potential and the strain variations adapt to and sense the electrical and chemical (exchanged cation) conditions. The driving and the response of actuation, sensing and charge can be controlled/read, simultaneously, via just two connecting wires. Only the cooperative actuation of chemical macromolecular motors from functional cells has such chemical multifunctionality.

Printed PEDOT:PSS Trilayer: Mechanism Evaluation and Application in Energy Storage

Combining ink-jet printing and one of the most stable electroactive materials, PEDOT:PSS (poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)), is envisaged to pave the way for the mass production of soft electroactive materials. Despite its being a well-known electroactive material, widespread application of PEDOT:PSS also requires good understanding of its response. However, agreement on the interpretation of the material's activities, notably regarding actuation, is not unanimous. Our goal in this work is to study the behavior of trilayers with PEDOT:PSS electrodes printed on either side of a semi-interpenetrated polymer network membrane in propylene carbonate solutions of three different electrolytes, and to compare their electroactive, actuation, and energy storage behavior. The balance of apparent faradaic and non-faradaic processes in each case is discussed. The results show that the primarily cation-dominated response of the trilayers in the three electrolytes is actually remarkably different, with some rather uncommon outcomes. The different balance of the apparent charging mechanisms makes it possible to clearly select one electrolyte for potential actuation and another for energy storage application scenarios.

Comparative Analysis of Fluorinated Anions for Polypyrrole Linear Actuator Electrolytes

Either as salts or room temperature ionic liquids, fluorinated anion-based electrolytes have been a common choice for ionic electroactive polymer actuators, both linear and bending. In the present work, propylene carbonate solutions of four electrolytes of the three hugely popular anions-triflouromethanesulfonate, bis(trifluoromethane)sulfonimide, and hexafluorophosphate were compared and evaluated in polypyrrole linear actuators. The actuation direction, the characteristics-performance relations influence the behavior of the actuators. Isotonic Electro-chemo-mechanical deformation (ECMD) measurements were performed to study the response of the PPy/DBS samples. The highest strain for pristine PPy/DBS linear actuators was found in range of 21% for LiTFSI, while TBAPF6 had the least cation involvement, suggesting the potential for application in durable and controllable actuators. Interesting cation effects on the actuation of the same anions (CF3SO3-) were also observed.