Safety parameters for pulp temperature during selective ablation of caries by KTP laser in vitro

Dentinal Hypersensitivity Treatment Using Diode Laser 980 nm: In Vivo Study

The discomfort of patients due to dentinal hypersensitivity (DH) is one of the main challenges that dentists face in daily practice. Difficulties in DH treatment gave rise to many protocols which are currently used. The aim of this clinical study is to evaluate the effectiveness of a new protocol on the reduction of dentinal hypersensitivity with diode laser 980 nm and the application of a graphite paste. 184 patients enrolled in the study, the degree of pain was evaluated by visual analog scale (VAS), graphite paste was applied on the exposed dentine before irradiation, the application of diode laser 980 nm with continuous mode, backward motion, tangential incidence of the beam in non-contact mode and a delivery output of 1 W. Fiber’s diameter was 320 μm and total exposure time depended on the time necessary to remove the graphite paste from the teeth. Statistical analyses were performed with Prism 5^® software. Pain in post-operative significantly decreased immediately after the treatment. Mean values stayed stable until a 6-month follow-up. The application is considered to be safe with long-term effectiveness.

Analysis of Human Tooth Pulp Chamber Temperature After 670 nm Laser Irradiation: In Vitro Study

OBJECTIVE

One of the limiting factors of employing laser radiation on dental therapies is the potential of causing thermal injuries to pulp tissues. The purpose of this study was to evaluate intra-chamber temperature increase on extracted human teeth exposed to 670 nm wavelength InGaAlP laser diode radiation.

MATERIALS AND METHODS

In vitro intra-chamber temperature measurements of 12 standardized human teeth (incisors, canines, premolars, and molars; n = 3) were taken both before and after laser radiation. A type-K thermocouple fast-response thermocouple wire with a 0.5 mm diameter probe was inserted into the tooth pulp chamber (ICEL-Manaus-brand). The laser device Lasotronic-brand InGaAlP laser diode was used to irradiate tooth enamel, perpendicularly to the external surface for 30 sec, with power of levels of 340, 272, 204, 136, and 68 mW. The measurements were taken at three time points: 0, 30 sec, and 3 min after the laser irradiation. Measurements were repeated 24 h after removal and reinsertion of the probe in the pulp chamber. The temperature gradient (ΔT in °C) was calculated (ΔT = final temperature-initial temperature) for each group. Data of ΔT were statistically analyzed by two-way analysis of variance (ANOVA) at the 95% confidence level and compared by Tukey post hoc test (α = 0.05).

RESULTS

ANOVA showed statistically significant differences to the interaction of factors (p < 0.05). The highest ΔT values obtained were observed to incisors with 340 mW, 272 mW; 204 mW of power (respectively 4.7°C, 4.2°C, and 3.1°C); and canines presented the lowest ΔT (0.8°C-0.3°C) with no influence of power output.

CONCLUSIONS

Since the thermal increase was observed in this study, especially in incisors, attention should be paid to avoid pulpal damage.

Dentinal tubules sealing by means of diode lasers (810 and 980 nm): a preliminary in vitro study

OBJECTIVE

The aim of this study was to evaluate the effect on dentinal surfaces of diode lasers (810 and 980 nm) at different parameters.

MATERIALS AND METHODS

Twenty-four caries-free human impacted wisdom teeth were used. The crowns were sectioned transversely in order to expose the dentin. The smear layer was removed by a 1 min application of ethylenediaminetetraacetic acid (EDTA). Each surface was divided into four quadrants irradiated at a different output power setting for each kind of laser: 0.8, 1, 1.6, and 2 W (energy densities: 2547, 3184, 5092, and 6366 J/cm(2), irradiation speed 1 mm/sec; optical fiber diameter: 200 μm; continuous and noncontact mode). Half of the samples were stained with a graphite paste. All specimens were sent for scanning electron microscopic (SEM) analysis. Pulp temperature increases in additional 20 teeth were measured by a thermocouple.

RESULTS

Diode laser irradiations at 0.8 and 1 W led to occlusion or narrowing of dentin tubules without provoking fissures or cracks. The application of graphite paste increased the thermal effects in dentin. Measurements of pulp temperature showed that irradiations at 0.8 and 1 W for a period of 10 sec in continuous mode increased pulp temperature (T ≤2°C).

CONCLUSIONS

Diode lasers (810 and 980 nm) used at 0.8 and 1 W for 10 sec in continuous mode were able to seal the dentin tubules. These parameters can be considered harmless for pulp vitality, and may be effective in the treatment of dentinal hypersensitivity.