Power density and external temperature of laser-treated root canals

Determining the optimal dose of 1940-nm thulium fiber laser for assisting the endodontic treatment

Insufficient cleaning, the complex anatomy of the root canal system, inaccessible accessory canals, and inadequate penetration of irrigants through dentinal tubules minimizes the success of the conventional endodontic treatment. Laser-assisted endodontic treatment enhances the quality of conventional treatment, but each laser wavelength has its own its own limitations. The optimal parameters for the antibacterial efficiency of a new wavelength, 1940-nm Thulium Fiber Laser, were firstly investigated in this study. This paper comprises of two preliminary analyses and one main experimental study, presents data about thermal effects of 1940-nm laser application on root canal tissue, effective sterilization parameters for bacteria, Enterococcus faecalis, and finally the antibacterial effectiveness of this 1940-nm Thulium Fiber Laser irradiation in single root canal. Based on these results, the optimal parameter range for safe laser-assisted root canal treatment was investigated in the main experiments. Comparing the antibacterial effects of four laser powers on an E. faecalis bacteria culture in vitro in 96-well plates showed that the most effective group was the one irradiated with 1 W of laser power (antibacterial effect corresponding to a log kill of 3). After the optimal laser power was determined, varying irradiation durations (15, 30, and 60 s) were compared in disinfecting E. faecalis. Laser application caused significant reduction in colony-forming unit values (CFU) compared with control samples in the 17% ethylenediaminetetraacetic acid (EDTA) group. The results of bacteria counts showed that 1 W with 30 s of irradiation with a 1940-nm thulium fiber laser was the optimal dose for safely achieving maximal bactericidal effect.

Temperature rise during photo-activated disinfection of root canals

The aim of this study was to determine whether it is safe to use photo-activated disinfection (PAD) during root canal treatment without heating the periodontal tissues. Root canals of 30 freshly extracted single-rooted teeth were prepared using ProFiles up to size ISO 40 and then filled with photo-sensitiser: tolonium blue (1.2 mg/l). The 635 nm diode laser was used with the manufacturer's endo-tip. Samples were irradiated for 150 s (output power 100 mW, approximate energy density 106.16 J/cm(2)). Temperatures were recorded at working length on the external root surface. After 150 s of PAD irradiation, the average temperature rise was 0.16 +/- 0.08 degrees C. All values were lower than the 7 degrees C safety level for periodontal injury. It was concluded that, regarding the temperature increase, the use of PAD in root canals could be considered harmless for periodontal tissues.

The use of the erbium, chromium:yttrium-scandium-gallium-garnet laser in endodontic treatment

BACKGROUND

The use of the erbium, chromium:yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser has become accepted in the field of cavity preparation. The development of miniaturized and flexible fiber tips has allowed this device to be used in endodontics. The authors conducted an in vitro study to assess the effects of Er,Cr:YSGG laser irradiation on root canals.

METHODS

The authors inoculated root canals with two bacteria, laser irradiated them at two power settings and subjected them to a quantitative microbiological evaluation. They used scanning electron microscopy (SEM) to assess morphological changes in endodontically processed and laser-irradiated root canal walls. They measured temperature increases on the root surface to determine possible thermal side effects.

RESULTS

The bacteriological evaluation revealed a disinfecting effect in the root dentin samples that was dependent on the output power but not specific for the bacterial species investigated. SEM showed the removal of the smear layer from the root canal walls and the exposure of dentinal tubules. The temperature rise during irradiation was moderate when standardized power settings were used.

CONCLUSIONS

The Er,Cr:YSGG laser can be used to eliminate bacteria in root canals. It also effectively removes smear layer and debris from the canal wall.

CLINICAL IMPLICATIONS

Practitioners can use the Er,Cr:YSGG laser to prepare root canals for endodontic therapy.

Influence of heat from light curing units and dental composite polymerization on cells in vitro

OBJECTIVES

The aim of the present study was to test the hypothesis that the use of a light curing unit (LCU) with high light power would result in a higher temperature and therefore a statistically significant lower number of living human gingiva fibroblasts within a pulp chamber model than the use of a light emitting diode (LED) LCU.

MATERIALS AND METHODS

The composites Admira, Grandio, Filtek Supreme and Filtek Z250 were polymerized with the LCUs Swiss Master Light, Optilux 501 and an LED LCU prototype in a mould on top of a pulp chamber model. The temperature was recorded within the pulp chamber with a thermocouple. The cytotoxicity of the polymerized samples was tested by using the MTT test.

RESULTS

In general there was no considerable difference in the temperature increase within the pulp chamber model for the different LCUs and composites. There was no statistically significant difference in the cell number (p=0.3767) when the different LCUs were used.

CONCLUSIONS

Using a high power halogen LCU for a short time or a standard halogen or LED LCU for a longer time did not result in a considerable difference in the temperature increase or the number of living cells within a pulp chamber model. This study indicates not only that the temperature may have an effect on the living cells, but also that cells may be negatively affected by the unpolymerized composite or light of the LCUs.

Laser-induced temperature changes in dentine

OBJECTIVE

The purpose of this work is to study the temperature rise and potential thermal damage caused during ablation of human dentine using a super pulsed carbon dioxide laser of 9.6-microm wavelength, equipped with a water-cooling spray and scanner system.

BACKGROUND DATA

There have been no reports on thermal effects of super pulsed CO2 laser of 9.6 microm wavelength on human dentine recently.

MATERIALS AND METHODS

Two different types of samples were investigated to yield data most consistent with a typical clinical situation. Human dentine slices and crown segments were studied at a drilling depth of 1.0 +/- 0.1 mm and 2.5 +/- 0.5 mm, respectively. A control group treated with a conventional hand piece was compared to four laser groups with settings varying from 2 to 8 W.

RESULTS

In the laser group demonstrating the highest elevation in temperature of the four studied, dentine slices lased at 2 W for 15 sec showed a mean temperature rise of less than 1.68 degrees C at an ablation rate of 0.86 +/- 0.08 mm. Conventional drilling with a comparable ablation rate of 0.76 +/- 0.59 mm resulted in a mean rise of 2.87 degrees C. The laser groups of crown segments revealed a constant decrease in temperature. SEM observations were lacking the typical morphological changes seen in earlier studies, specifically extensive melting, charring or cracking.

CONCLUSION

A maximum rise of mean temperature to 1.68 degrees C in closest vicinity to the pulpal chamber and the morphological unaltered dentine surfaces demonstrate the safe and tissue preserving character of the superpulsed 9.6 microm CO2 laser. The laser caused an even lower temperature rise than conventional drilling. Moreover, the laser showed acceptable efficacy with ablation rates that did not significantly differ from the conventional dental drill.