Finite-element modelling of interactions of needle with tympanic membrane and middle ear

The tympanic membrane (TM) is one of the most common routes to access the middle ear and inner ear for the treatment of hearing and balance pathologies. Since the TM is a soft thin biological tissue with small dimensions, using needles seems to be among the most practical interventional approaches. In this study, we proposed a finite-element (FE) analysis of needle-TM interactions that combines a 3D model of the TM and other main middle-ear structures in gerbil, and a 2D model of needle insertion into the TM based on the cohesive zone method (CZM). The TM was modelled using a 1st-order Ogden hyperelastic material and its properties were obtained by fitting to the experimental force-displacement plots of large deformation in the TM under needle indentation. The cohesive parameters were also acquired by calibrating the puncture force against the experimental data of needle insertion into the TM. These FE models were then used to obtain the deformation behaviour of the TM and other middle-ear structures due to the insertion force applied at different locations on the TM. Moreover, we investigated the effect of the TM thickness, the geometry of the needle (i.e., diameter and tip angle), and needle material on the insertion of needles into the TM. We also studied the penetration success of deformable needles.

Experimental Study of Needle Insertion into Gerbil Tympanic Membrane

The perforation characteristics and fracture-related mechanical properties of the tympanic membrane (TM) greatly affect surgical procedures like myringotomy and tympanostomy performed on the middle ear. We analyzed the most important features of the gerbil TM perforation using an experimental approach that was based on force measurement during a 2-cycle needle insertion/extraction process. Fracture energy, friction energy, strain energy, and hysteresis loss were taken into consideration for the analysis of the different stages of needle insertion and extraction. The results demonstrated that (1) although the TM shows viscoelastic behavior, the contribution of hysteresis loss was negligible compared to other irreversible dissipated energy components (i.e., fracture energy and friction energy). (2) The TM puncture force did not substantially change during the first hours after animal death, but interestingly, it increased after 1 week due to the drying effects of soft tissue. (3) The needle geometry affected the crack length and the most important features of the force-displacement plot for the needle insertion process (puncture force, puncture displacement, and jump-in force) increased with increasing needle diameter, whereas the insertion velocity only changed the puncture and jump-in forces (both increased with increasing insertion velocity) and did not have a noticeable effect on the puncture displacement. (4) The fracture toughness of the gerbil TM was almost independent of the needle geometry and was found to be around 0.33 ± 0.10 kJ/m2.

Real-time measurement of stapes motion and intracochlear pressure during blast exposure

Blast-induced auditory injury is primarily caused by exposure to an overwhelming amount of energy transmitted into the external auditory canal, the middle ear, and then the cochlea. Quantification of this energy requires real-time measurement of stapes footplate (SFP) motion and intracochlear pressure in the scala vestibuli (Psv). To date, SFP and Psv have not been measured simultaneously during blast exposure, but a dual-laser experimental approach for detecting the movement of the SFP was reported by Jiang et al. (2021). In this study, we have incorporated the measurement of Psv with SFP motion and developed a novel approach to quantitatively measure the energy flux entering the cochlea during blast exposure. Five fresh human cadaveric temporal bones (TBs) were used in this study. A mastoidectomy and facial recess approach were performed to identify the SFP, followed by a cochleostomy into the scala vestibuli (SV). The TB was mounted to the "head block", a fixture to simulate a real human skull, with two pressure sensors - one inserted into the SV (Psv) and another in the ear canal near the tympanic membrane (P1). The TB was exposed to the blast overpressure (P0) around 4 psi or 28 kPa. Two laser Doppler vibrometers (LDVs) were used to measure the movements of the SFP and TB (as a reference). The LDVs, P1, and Psv signals were triggered by P0 and recorded simultaneously. The results include peak values for Psv of 100.8 ± 51.6 kPa (mean ± SD) and for SFP displacement of 72.6 ± 56.4 μm, which are consistent with published experimental results and finite element modeling data. Most of the P0 input energy flux into the cochlea occurred within 2 ms and resulted in 10-70 μJ total energy entering the cochlea. Although the middle ear pressure gain was close to that measured under acoustic stimulus conditions, the nonlinear behavior of the middle ear was observed from the elevated cochlear input impedance. For the first time, SFP movement and intracochlear pressure Psv have been successfully measured simultaneously during blast exposure. This study provides a new methodology and experimental data for determining the energy flux entering the cochlea during a blast, which serves as an injury index for quantifying blast-induced auditory damage.

Prevention of Blast-induced Auditory Injury Using 3D Printed Helmet and Hearing Protection Device - A Preliminary Study on Biomechanical Modeling and Animal

INTRODUCTION

Repeated blast exposures result in structural damage to the peripheral auditory system (PAS) and the central auditory system (CAS). However, it is difficult to differentiate injuries between two distinct pathways: the mechanical damage in the PAS caused by blast pressure waves transmitted through the ear and the damage in the CAS caused by blast wave impacts on the head or traumatic brain injury. This article reports a preliminary study using a 3D printed chinchilla "helmet" as a head protection device associated with the hearing protection devices (e.g., earplugs) to isolate the CAS damage from the PAS injuries under repeated blast exposures.

MATERIALS AND METHODS

A finite element (FE) model of the chinchilla helmet was created based on micro-computed tomography images of a chinchilla skull and inputted into ANSYS for FE analysis on the helmet's protection against blast over pressure. The helmet was then 3D printed and used for animal experiments. Chinchillas were divided into four cases (ears open, with earplug only, with both earplug and helmet, and with helmet only) and exposed to three blasts at blast over pressure of 15 to 20 psi. Hearing function tests (e.g., auditory brainstem response) were performed before and after blast on Day 1 and Days 4 and 7 after blasts.

RESULTS

The FE model simulation showed a significant reduction in intracranial stress with the helmet, and the animal results indicated that both earplug and helmet reduced the severity of blast-induced auditory injuries by approximately 20 dB but with different mechanisms.

CONCLUSIONS

The biomechanical modeling and animal experiments demonstrated that this four-case study in chinchillas with helmet and hearing protection devices provides a novel methodology to investigate the blast-induced damage in the PAS and CAS.

Dual-laser measurement of human stapes footplate motion under blast exposure

Hearing damage is one of the most frequently observed injuries in Service members and Veterans even though hearing protection devices (HPDs, e.g. earplugs) have been implemented to prevent blast-induced hearing loss. However, the formation and prevention mechanism of the blast-induced hearing damage remains unclear due to the difficulty for conducting biomechanical measurements in ears during blast exposure. Recently, an approach reported by Jiang et al. (2019) used two laser Doppler vibrometers (LDVs) to measure the motion of the tympanic membrane (TM) in human temporal bones during blast exposure. Using the dual laser setup, we further developed the technology to detect the movement of the stapes footplate (SFP) in ears with and without HPDs while under blast exposure. Eight fresh human cadaveric temporal bones (TBs) were involved in this study. The TB was mounted in a "head block" after performing a facial recess surgery to access the SFP, and a pressure sensor was inserted near the TM in the ear canal to measure the pressure reaching the TM (P1). The TB was exposed to a blast overpressure measuring around 7 psi or 48 kPa at the entrance of the ear canal (P0). Two LDVs were used to measure the vibrations of the SFP and TB (as a reference). The exact motion of the SFP was determined by subtracting the TB motion from the SFP data. Results included a measured peak-to-peak SFP displacement of 68.7 ± 31.6 μm (mean ± SD) from all eight TBs without HPDs. In five of the TBs, the insertion of a foam earplug reduced the SFP displacement from 48.3 ± 6.3 μm to 21.8 ± 10.4 μm. The time-frequency analysis of the SFP velocity signals indicated that most of the energy spectrum was concentrated at frequencies below 4 kHz within the first 2 ms after blast and the energy was reduced after the insertion of HPDs. This study describes a new methodology to quantitatively characterize the response of the middle ear and the energy entering the cochlea during blast exposure. The experimental data are critical for determining the injury of the peripheral auditory system and elucidating the damage formation and prevention mechanism in an ear exposed to blast.

3D Finite Element Modeling of Blast Wave Transmission from the External Ear to Cochlea

As an organ that is sensitive to pressure changes, the ear is often damaged when a person is subjected to blast exposures resulting in hearing loss due to tissue damage in the middle ear and cochlea. While observation of middle ear damage is non-invasive, examining the damage to the cochlea is difficult to quantify. Previous works have modeled the cochlear response often when subjected to an acoustic pressure input, but the inner ear mechanics have rarely been studied when the ear is exposed to a blast wave. In this study we aim to develop a finite element (FE) model of the entire ear, particularly the cochlea, for predicting the blast wave transmission from the ear canal to cochlea. We utilized a FE model of the ear, which includes the ear canal, middle ear, and uncoiled two-chambered cochlea, to simulate the cochlear response to blast overpressure (BOP) at the entrance of the ear canal with ANSYS Mechanical and Fluent in a fluid-structure interface coupled analysis in the time domain. This model was developed based on previous middle and inner ear models, and the cochlea was remeshed to improve BOP simulation performance. The FE model was validated using experimentally measured blast pressure transduction from the ear canal to the middle ear and cochlea in human cadaveric temporal bones. Results from the FE model showed significant displacements of the tympanic membrane, middle ear ossicles, and basilar membrane (BM). The stapes footplate displacement was observed to be as high as 60 µm, far exceeding the displacement during normal acoustic stimulation, when the 30 kPa (4.35 psi, 183 dB (SPL), Sound Pressure Level) of BOP was applied at the ear canal entrance. The large stapes movement caused pressures in the cochlea to exceed the physiological pressure level [< 10 Pa, 120 dB (SPL)] at a peak of 49.9 kPa, and the BM displacement was on the order of microns with a maximum displacement of 26.4 µm. The FE model of the entire human ear developed in this study provides a computational tool for prediction of blast wave transmission from the ear canal to cochlea and the future applications for assisting the prevention, diagnosis, and treatment of blast-induced hearing loss.

Silicon foil patching for blast tympanic membrane perforation: a retrospective study

Aim

To establish whether covering the tympanic membrane perforation after war blast injury with silicon foil can enhance the ear drum healing rate and to determine the appropriate timing of silicon patching.

Methods

We retrospectively analyzed the charts of 210 patients wounded during the Homeland War in Croatia 1991-1995, with 315 blast tympanic membrane perforations. In 44 patients (61 perforations), the eardrum perforation was covered by silicon foil, whereas in 166 patients (254 perforations) it was left to heal spontaneously. The patients who underwent the patching procedure were divided in two groups according to the time period between the blast injury and the procedure: 38 perforations were treated within 3 days and 23 perforations were treated 4 to 6 days after the blast injury.

Results

The rate of tympanic membrane healing in the silicon foil patching group was significantly higher (91.8%) than that in the group of perforations left to heal spontaneously (79.9%, P = 0.029). The healing rate was significantly higher in the group treated within 3 days after the blast injury (97.4%) than in the group treated 4 to 6 days after the injury (82.6%, P = 0.042).

Conclusion

Covering the perforation after the war blast injury with silicon foil significantly improves the rate of tympanic membrane healing. To obtain the best healing outcome, the procedure should be performed within the first 72 hours after the trauma.

The effect of blast overpressure on the mechanical properties of the human tympanic membrane

The rupture of the tympanic membrane (TM) is one of the major indicators for blast injuries due to the vulnerability of TM under exposure to blast overpressure. The mechanical properties of the human TM exhibit a significant change after it is exposed to such a high intensity blast. To date, the published data were obtained from measurement on TM strips cut from a TM following an exposure to blast overpressure. The dissection of a TM for preparation of strip samples can induce secondary damage to the TM and thus potentially lead to data not representative of the blast damage. In this paper, we conduct mechanical testing on the full TM in a human temporal bone. A bulging experiment on the entire TM is carried out on each sample prepared from a temporal bone following the exposure to blast three times at a pressure level slightly below the TM rupture threshold. Using a micro-fringe projection method, the volume displacement is obtained as a function of pressure, and their relationship is modeled in the finite element analysis to determine the mechanical properties of the post-blast human TMs, the results of which are compared with the control TMs without an exposure to the blast. It is found that Young's modulus of human TM decreases by approximately 20% after exposure to multiple blast waves. The results can be used in the human ear simulation models to assist the understanding of the effect of blast overpressure on hearing loss.

Surface Motion Changes of Tympanic Membrane Damaged by Blast Waves

Eardrum or tympanic membrane (TM) is a multilayer soft tissue membrane located at the end of the ear canal to receive sound pressure and transport the sound into the middle ear and cochlea. Recent studies reported that the TM microstructure and mechanical properties varied after the ear was exposed to blast overpressure. However, the impact of such biomechanical changes of the TM on its movement for sound transmission has not been investigated. This paper reports the full-field surface motion of the human TM using the scanning laser Doppler vibrometry in human temporal bones under normal and postblast conditions. An increase of the TM displacement after blast exposure was observed in the posterior region of the TM in four temporal bone samples at the frequencies between 3 and 4 kHz. A finite element model of human TM with multilayer microstructure and orthogonal fiber network was created to simulate the TM damaged by blast waves. The consistency between the experimental data and the model-derived TM surface motion suggests that the tissue injuries were resulted from a combination of mechanical property change and regional discontinuity of collagen fibers. This study provides the evidences of surface motion changes of the TM damaged by blast waves and possible fiber damage locations.

Characterization of Protection Mechanisms to Blast Overpressure for Personal Hearing Protection Devices – Biomechanical Measurement and Computational Modeling

Hearing damage induced by blast exposure is a common injury in military personnel involved in most operation activities. Personal hearing protection devices such as earplugs come as a standard issue for Service members; however, it is not clear how to accurately evaluate the protection mechanisms of different hearing protection devices for blast overpressures (BOP). This paper reports a recent study on characterization of earplugs’ protective function to BOP using human cadaver ears and 3D finite element (FE) model of the human ear. The cadaver ear mounted with pressure sensors near the eardrum (P1) and inside the middle ear (P2) and with an earplug inserted was exposed to BOP in the blast test chamber. P1, P2, and BOP at the ear canal entrance (P0) were simultaneously recorded. The measured P0 waveform was then applied at the ear canal entrance in the FE model and the P1 and P2 pressures were derived from the model. Both experiments and FE modeling resulted in the P1 reduction which represents the effective protection function of the earplug. Different earplugs showed variations in pressure waveforms transmitted to the eardrum, which determine the protection level of earplugs.