Effect of hip hemiarthroplasty on articular cartilage and bone in a canine model

Patient-specific 3D-printed shelf implant for the treatment of hip dysplasia: Anatomical and biomechanical outcomes in a canine model

A solution for challenging hip dysplasia surgery could be a patient-specific 3D-printed shelf implant that is positioned extra-articular and restores the dysplastic acetabular rim to normal anatomical dimensions. The anatomical correction and biomechanical stability of this concept were tested in a canine model that, like humans, also suffers from hip dysplasia. Using 3D reconstructed computed tomography images the 3D shelf implant was designed to restore the radiological dysplastic hip parameters to healthy parameters. It was tested ex vivo on three dog cadavers (six hips) with hip dysplasia. Each hip was subjected to a biomechanical subluxation test, first without and then with the 3D shelf implant in place. Subsequently, an implant failure test was performed to test the primary implant fixation. At baseline, the dysplastic hips had an average Norberg angle of 88 ± 3° and acetabular coverage of 47 ± 2% and subluxated at an average of 83 ± 2° of femoral adduction. After adding the patient-specific shelf implants the dysplastic hips had an average Norberg angle of 122 ± 2° and acetabular coverage of 67 ± 3% and subluxated at an average of 117 ± 2° of femoral adduction. Implant failure after primary implant fixation occurred at an average of 1330 ± 320 Newton. This showed that the patient-specific shelf implants significantly improved the coverage and stability of dysplastic hips in a canine model with naturally occurring hip dysplasia. The 3D shelf is a promising concept for treating residual hip dysplasia with a straightforward technology-driven approach; however, the clinical safety needs to be further investigated in an experimental proof-of-concept animal study.

Short-Term Clinical Assessment of Hip Hemi-Arthroplasty in 11 Dogs

OBJECTIVE

 The aim of this study was to assess the short-term clinical outcome in dogs following a hip hemi-arthroplasty for the treatment of primary pathological disorders of the hip and as a salvage procedure following failure of the cup component of a total hip replacement.

MATERIALS AND METHODS

 Medical records of dogs that had a unilateral hip hemi-arthroplasty performed between 2015 and 2020 were reviewed. Data collected included follow-up orthopaedic examinations performed at 0, 2, 8 and 52 weeks postoperatively, pelvic radiography at 0, 8 and 52 weeks postoperatively and an owner questionnaire (Helsinki chronic pain index [HCPI]).

RESULTS

 Eleven unilateral hip hemi-arthroplasty procedures were identified. The median age at time of surgery was 3.6 years (8 months-10 years) and the median follow-up time was 13 months (range: 2 months-3 years). The HCPI for all dogs at follow-up was median 8 ± 7.30 (range: 5-25). Total HCPI was < 12 for 7/10 dogs and ≥ 12 for 3 dogs. Pelvic radiographs at 1 year confirmed osteointergration of the femoral stem implant and no evidence of implant subsidence or progression of osteoarthritis. However, there was some evidence of mild lucency of the acetabular bed around the prosthetic femoral head and mild peri-acetabular sclerosis in four cases.

CONCLUSION

 Hip hemi-arthroplasty provides a clinically acceptable treatment for disabling disease of the coxofemoral joint with 10/11 patients achieving acceptable short-term clinical function. Long-term assessment of the hip hemi-arthroplasty and comparison with total hip replacement is indicated.

Biological responses to individualized small titanium implants for the treatment of focal full-thickness knee cartilage defects in a sheep model

BACKGROUND

The present study aimed to evaluate the functional, radiological and histological outcome of a customized focal implant for the treatment of focal full-thickness cartilage defects in sheep.

METHODS

The study used magnetic resonance imaging data as the basis for construction of the titanium implant using a three-dimensional printing technique. This was then placed on the medial condyle of the knee joint in eight sheep and left in place in vivo over a period of six months. Following euthanasia, the local biological response was analyzed using micro-computed tomography, light microscopy and histological evaluation (International Cartilage Repair Society (ICRS) score). The variables were analyzed using a generalized linear mixed model. Odds ratios were given with 95% confidence intervals.

RESULTS

The osseointegration rate was 62.1% (SD 3.9%). All implants were prone to the neighboring cartilage bed (4.4-1096.1 μm). Using the IRCS score, the elements 'surface', 'matrix', 'cell distribution' and 'cell population' all showed pathological changes on the operated side, although these did not correlate with implant elevation. On average, a difference of 0.7 mm (±2 mm) was found between the digitally planned implant and the real implant.

CONCLUSIONS

As a result of imprecise segmentation and difficult preparation conditions at the prosthesis bed, as well as changes at the surface of the implant over the operational lifetime of the prosthesis, it must be stated that the approach implemented here of using a customized implant for the treatment of focal full-thickness cartilage defects at the knee did not meet our expectations.

Histological evaluation of the acetabular labrum after bipolar hip hemiarthroplasty: a case report

We report herein the microstructure of the acetabular labrum obtained from a patient with stem loosening but without bipolar cup migration who had undergone hemiarthroplasty for femoral neck fracture 18 years ago. We used light and scanning electron microscopy to investigate the influence of bipolar cup on acetabular labrum in vivo. Deparaffinized blocks were treated with 2 N NaOH to digest the cell matrix, allowing the collagen fibers, constituting the acetabular labrum, to be observed under scanning electron microscopy. Although chondrocyte atrophy was seen, the basic structure was not different from the normal tissue images of the elderly. However, in the deep part of the acetabular labrum, there was an area that was not stained with Alcian blue observed with light microscopy, and there was an amorphous tissue without type II collagen fibrils observed with scanning electron microscopy. These findings proved that the acetabular labrum has partially degenerated over the long term after bipolar hemiarthroplasty, and that the acetabular labrum can survive in vivo in such a condition. Given that hemiarthroplasty has a possibility to preserve the face-to-face tissue in the long term in vivo, it may be one of the valuable options for modern or future joint reconstruction surgery.

Early acetabular cartilage wear following hemiarthroplasty: An ovine model

Objectives: Hemiarthroplasty induces degenerative changes in the hip joint, which are difficult to evaluate in vivo. Radiostereometric analysis (RSA) is a radiographic measurement technique that has recently been used to measure acetabular cartilage wear in vivo. The aim of the study was to measure acetabular cartilage wear, using this technique, in an ovine model during the first 14 weeks post-implantation.

Methods: Measurements of three-dimensional femoral head migration, combined with visual assessments at necropsy and safranin O staining for cartilage integrity, were undertaken.

Results: Mean femoral head migration during the first six weeks was 0.525 mm in the medial, 0.144 mm in the cranial, and 0.517 mm in the dorsal direction. The majority of this migration was confirmed to be cartilage wear in the medial and dorsal aspects of the acetabulum at necropsy and with subsequent histological evaluation depicting significant cartilage degeneration.

Clinical significance: Radiostereometric analysis is the current gold standard technique for in vivo assessment of implant migration following total hip replacement. This study has utilized RSA to quantify the amount of early cartilage wear in vivo, which was supported by ex vivo evaluations. Accurately measuring the amount of cartilage wear will allow future studies to compare component material and design characteristics prior to clinical use.

ESTABLISHING A LIVE CARTILAGE-ON-CARTILAGE INTERFACE FOR TRIBOLOGICAL TESTING

Mechano-biochemical wear encompasses the tribological interplay between biological and mechanical mechanisms responsible for cartilage wear and degradation. The aim of this study was to develop and start validating a novel tribological testing system, which better resembles the natural joint environment through incorporating a live cartilage-on-cartilage articulating interface, joint specific kinematics, and the application of controlled mechanical stimuli for the measurement of biological responses in order to study the mechano-biochemical wear of cartilage. The study entailed two parts. In Part 1, the novel testing rig was used to compare two bearing systems: (a) cartilage articulating against cartilage (CoC) and (b) metal articulating against cartilage (MoC). The clinically relevant MoC, which is also a common tribological interface for evaluating cartilage wear, should produce more wear to agree with clinical observations. In Part II, the novel testing system was used to determine how wear is affected by tissue viability in live and dead CoC articulations. For both parts, bovine cartilage explants were harvested and tribologically tested for three consecutive days. Wear was defined as release of glycosaminoglycans into the media and as evaluation of the tissue structure. For Part I, we found that the live CoC articulation did not cause damage to the cartilage, to the extent of being comparable to the free swelling controls, whereas the MoC articulation caused decreased cell viability, extracellular matrix disruption, and increased wear when compared to CoC, and consistent with clinical data. These results provided confidence that this novel testing system will be adequate to screen new biomaterials for articulation against cartilage, such as in hemiarthroplasty. For Part II, the live and dead cartilage articulation yielded similar wear as determined by the release of proteoglycans and aggrecan fragments, suggesting that keeping the cartilage alive may not be essential for short term wear tests. However, the biosynthesis of glycosaminoglycans was significantly higher due to live CoC articulation than due to the corresponding live free swelling controls, indicating that articulation stimulated cell activity. Moving forward, the cell response to mechanical stimuli and the underlying mechano-biochemical wear mechanisms need to be further studied for a complete picture of tissue degradation.

The cartilage degeneration and joint motion of bipolar hemiarthroplasty

PURPOSE

The outcomes of bipolar hemiarthoplasty for osteonecrosis of femoral head have been disappointing due to cartilage degeneration and osteolysis. We investigated the cartilage degeneration, joint motion, and factors associated with osteolysis.

METHODS

We retrospectively reviewed 134 bipolar hemiarthroplasties. The wear rate of acetabular cartilage was calculated. The ranges of motion of outer bearing and inner bearing were determined, and the ratio (O/I ratio) was calculated.

RESULTS

The mean degeneration rate of acetabular cartilage was 0.34 ± 0.35 mm/year. We could observe that the outer bearing motion was dominant, but decreased over time. In addition, the degeneration rate of cartilage and the decline rate of outer bearing motion of the osteolysis group were significantly higher than those of the control group.

CONCLUSIONS

Close observation is needed in cases of high degeneration rate of cartilage and rapid decline of outer bearing motion due to possibility of osteolysis.

Comparison of human and animal femoral head chondral properties and geometries

Investigations into tissue-preserving orthopaedic treatments should consider the tribology of articular cartilage; where simulations using animal joints are a predominant choice. However, very few studies have investigated the differences between human and animal cartilage. The aim of the present study was to characterise the differences in geometry and mechanical properties of human, porcine, bovine and ovine articular cartilage. Creep indentation was performed on osteochondral plugs taken from the superior region of femoral heads of all these species. Cartilage thickness was measured via the resistive force change of a needle descending through cartilage and bone. A biphasic finite element model was used to derive equilibrium elastic modulus and permeability. Results showed that human cartilage was significantly thicker than all other species tested. A positive correlation was found between femoral head diameter and cartilage thickness when comparing between species of quadrupeds. Human cartilage had the largest equilibrium elastic modulus, which was significant when comparing against porcine and bovine. However, porcine cartilage had significantly lower permeability. Significant differences in geometry and mechanical properties of articular cartilage were found between all species tested. It is necessary to consider these variations when choosing animal tissue to represent human.

Radiostereometric analysis of hemiarthroplasties of the hip--a highly precise method for measurements of cartilage wear

OBJECTIVE

Cartilage wear is a feature of osteoarthritis and rheumatoid arthritis. Precise measurements of wear have been difficult. Cartilage wear caused by an artificial articulating joint surface is a well-known feature of hemiarthroplasties. The aim of this study was to demonstrate that radiostereometric analysis (RSA) may be used for three-dimensional measurements of cartilage wear in hemiarthroplasties of the hip.

METHOD

We performed a phantom model study to assess the feasibility of a subsequent clinical trial. We showed that the motion of the prosthetic head relative to the pelvis was not influenced by the orientation of the prosthetic head. Twenty-two patients were randomised to treatment with a cemented or an uncemented hemiarthroplasty for an acute femoral neck fracture. Migration of the prosthetic head into the acetabulum was measured using RSA.

RESULTS

A mean migration of the prosthetic head into the acetabulum of 0.62 mm was found at 3 months [95% confidence interval (CI): 0.27-0.97] and a further migration of -0.07 mm at 12 months (95% CI: -0.16-0.32). There were no differences between the groups in prosthetic migration or functional outcome. Between three and 12 months, there was no detectable cartilage wear during the first postoperative year.

CONCLUSION

Whether the migration during the first 3 months represents a period of bedding in due to a harder opposite surface remains to be shown. RSA may be used for measurement of cartilage wear in hemiarthroplasties of the hip. This study demonstrates a highly precise method for measurements of cartilage wear.

The effect of contact stress on cartilage friction, deformation and wear

Following hip hemiarthroplasty, a metal femoral head articulates against natural acetabular cartilage. Cartilage friction and wear may be influenced by variables including loading time, contact stress, contact area, sliding distance, and sliding speed. The aim of this study was to investigate the effect of these variables on cartilage friction, deformation and wear in a simulation using idealized geometry model. Bovine cartilage pins were reciprocated against metal plates to mimic a hemiarthroplasty articulation under static loading. The effective coefficient of friction (µeff) under contact stresses (0.5 to 16 MPa), contact areas (12 and 64 mm2), stroke lengths (4 and 8 mm), sliding velocities (4 and 8 mm/s), and loading time (1 and 24 hours) were studied. The permanent deformation of cartilage (after 24 hours of recovery) with and without motion was recorded to assess cartilage linear wear.

The µeff was found to remain < 0.35 with contact stresses ≤ 4 MPa. Severe damage to the cartilage occurred at contact stresses > 8 MPa and significantly increased µeff after 12 hours of reciprocation. In long-term, contact area had no significant effect on µeff, and sliding distance and velocity only affected µeff under low contact stresses. The cartilage linear wear increased with contact stress, sliding distance and velocity.

Analysis of frictional behavior and changes in morphology resulting from cartilage articulation with porous polyurethane foams

Porous polyurethane foams (PUR) have been extensively evaluated as meniscal replacement materials and show great promise enabling infiltration of cells and fibrocartilage formation in vivo. Similar to most materials, PUR demonstrates progressive degeneration of opposing cartilage; however, the damage mechanism is impossible to determine because no information exists on the frictional properties of PUR-cartilage interfaces. The goals of this study were to characterize the frictional behavior of a cartilage-PUR interface across a range of articulating conditions and assess the resulting morphological changes to the cartilage surface following articulation. Articular cartilage was oscillated against PUR or stainless steel using phosphate-buffered saline (PBS) and synovial fluid as lubricants. Following friction testing, cartilage and PUR samples were analyzed with environmental scanning electron microscopy and histological staining to determine changes in tissue morphology. Stribeck-surface analysis demonstrated distinct lubrication modes; however, boundary mode lubrication was dominant in cartilage-PUR interfaces and the low-friction pressure-borne lubrication mechanism present in native joints was absent. Microscopy noted obvious wear, with disruption of the collagen architecture and concomitant proteoglycan loss in cartilage articulated against PUR. These data collectively point to the importance of frictional properties as design parameters for implants and materials for soft tissue replacement.

Pyrolytic carbon endoprosthetic replacement for osteonecrosis and femoral fracture of the hip: a pilot study

Hemiarthroplasty in young patients has the potential for eliminating bearing wear, but has the disadvantage of cartilage wear. Low-temperature isotropic (LTI) pyrolytic carbon reportedly reduces cartilage wear in canine hemiarthroplasties. We therefore initiated a study in humans when it was released for human use. However, we observed failures in some patients. We therefore document and report the high failure rate observed in a subset of patients treated with an LTI pyrolytic carbon femoral head for osteonecrosis. We conducted a prospective pilot study of 17 patients treated with a titanium stem and an LTI pyrolytic carbon femoral head bearing surface for unipolar hemiarthroplasty for either femoral neck fracture (10 patients) or osteonecrosis (seven patients). One of 10 patients in the fracture group underwent conversion to THA as a result of arthritic progression compared with six of seven patients with osteonecrosis who underwent conversion to THA as a result of acetabular wear and severe groin pain. In this small series, patients with osteonecrosis had a higher rate of revision compared with the patients treated for femoral neck fracture.

LEVEL OF EVIDENCE

Level III, therapeutic study.

Degeneration of acetabular articular cartilage to bipolar hemiarthroplasty

PURPOSE

This study examined the rate of degeneration of acetabular cartilage by the bipolar head according to time, and also which clinical factors are related to the degeneration of acetabular cartilage.

MATERIALS AND METHODS

Among 192 patients (226 hip joints) who received bipolar hemiarthroplasty from August 1996 to August 2002, 61 patients (65 hip joints) were enrolled in this study, who were followed up for more than 2 years and showed no signs of dislocation, infection, or functional problems. A modified form of a computer assisted vector wear analysis program was used to measure the rate of degeneration of the acetabular cartilage. The factors that appeared to affect the rate of acetabular degeneration in the two groups was evaluated.

RESULTS

The average linear degenerative change in the acetabular cartilage and the volumetric degenerative change were 0.23 +/- 0.107mm/year and 114 +/- 47.2mm3/year, respectively. The result showed significant differences in activity and HHS between the 2 groups. The HHS showed a reverse relationship with the linear degeneration and volumetric degeneration, and the activity showed a correlation with the linear and volumetric degeneration.

CONCLUSION

The acetabular cartilage degenerates faster as the patient' activity increases, and slower with a higher HHS. When surgeons perform hip joint arthroplasty, it is strongly recommended that the life expectancy and the level of activity should be considered when deciding between a hemiarthroplasty and total hip arthroplasty.