Laparoscopic Major Vascular Injury Simulation Using a Synthetic Compared With Porcine Model

Chemical Components of Smoke Produced From Versatile Training Tissue Models Using Electrocautery

INTRODUCTION

While exposure of surgeons and other staff to surgical smoke is an increasing health risk concern, there is a similar risk for users in surgical simulation and training. This study was undertaken to determine the chemical composition of smoke produced from a novel training model, Versatile Training Tissue (VTT), which is used for surgical simulation and training, and to compare this with smoke from a chemosynthetic model and porcine muscle and liver.

METHODS

A variety of models (VTT, polyvinyl alcohol, porcine muscle and liver) were prepared and cauterized. Identification of chemical substances in smoke was performed using gas chromatography-mass spectrometry. Quantitative instrumental analysis was implemented with gas chromatography-mass spectrometry and high-performance liquid chromatography. A convenient analysis was performed with a general smoke tube kit.

RESULTS

The main chemical components of smoke produced from VTT models include water and carbon dioxide. A small number of organic compounds were detected. Versatile Training Tissue models produced smoke with fewer compounds than smoke from a chemosynthetic model or porcine muscle.

CONCLUSIONS

The concentration of organic compounds from VTT models is considered to be below relevant health risk limits and lower than from polyvinyl alcohol and porcine muscle models. Although porcine liver smoke contains less of the main organic compounds of concern than a KM, it contains potentially hazardous nitrile compounds that are absent in KM smoke. Therefore, surgical simulation and training with VTT models should be considered relatively safe for trainees.

A review of simulation training and new 3D computer-generated synthetic organs for robotic surgery education

We conducted a comprehensive review of surgical simulation models used in robotic surgery education. We present an assessment of the validity and cost-effectiveness of virtual and augmented reality simulation, animal, cadaver and synthetic organ models. Face, content, construct, concurrent and predictive validity criteria were applied to each simulation model. There are six major commercial simulation machines available for robot-assisted surgery. The validity of virtual reality (VR) simulation curricula for psychomotor assessment and skill acquisition for the early phase of robotic surgery training has been demonstrated. The widespread adoption of VR simulation has been limited by the high cost of these machines. Live animal and cadavers have been the accepted standard for robotic surgical simulation since it began in the early 2000s. Our review found that there is a lack of evidence in the literature to support the use of animal and cadaver for robotic surgery training. The effectiveness of these models as a training tool is limited by logistical, ethical, financial and infection control issues. The latest evolution in synthetic organ model training for robotic surgery has been driven by new 3D-printing technology. Validated and cost-effective high-fidelity procedural models exist for robotic surgery training in urology. The development of synthetic models for the other specialties is not as mature. Expansion into multiple surgical disciplines and the widespread adoption of synthetic organ models for robotic simulation training will require the ability to engineer scalability for mass production. This would enable a transition in robotic surgical education where digital and synthetic organ models could be used in place of live animals and cadaver training to achieve robotic surgery competency.

Development of cadaver perfusion models for surgical training: an experimental study

PURPOSE

Perfusion techniques on cadavers are heterogeneous and imperfect. The objective of this study was to improve the existing circulation model for surgical simulation on cadavers.

METHODS

We used a three-step experimental approach. The first part of the experiment tested two variables: the type of circuit and the use of a heater for perfusion. The second approach evaluated two parameters: the injection fluid and the type of body conditioning (embalmed or freshly dead prepared using different washing techniques). The third one was an improvement on the best circulation obtained, which focused on the injection fluid. To compare the realism of these different techniques, we constructed a score with realism parameters: the volume of return flow, the presence of peripheral venous return and the perfusion of abdominal arteries.

RESULTS

We found that the use of a heater seemed to improve the perfusion, while performing an arteriovenous bypass did not seem very effective. A correlation rate of 0.84 was found between the realism score and the injected fluid chosen. The best score (4/6) was found for a non-embalmed body with a low-pressure washing technique using a gelatin-based liquid at a concentration of 4 g/L for circulation. Scores obtained using embalmed bodies for both injection fluids for high-pressure washing or for 8-g/L gelatin injection fluid did not exceed 3/6.

CONCLUSIONS

We showed that using a non-embalmed body with low-pressure washing and a 4-g/L gelatin-based fluid was the most effective technique for cadaver perfusion.