3D Modeling of Lower Extremities With Biplanar Radiographs: Reliability of Measures on Subsequent Examinations

Comparison of Lower-Limb Alignment in Patients with Advanced Knee Osteoarthritis: EOS Biplanar Stereoradiography versus Conventional Scanography

Background

Accurate measurement of the lower limb alignment is one of the most crucial factors in advanced knee osteoarthritis patients scheduled for surgery. Recently, EOS biplanar stereoradiography with three-dimensional reconstruction was developed. The purpose of this study was to compare radiographic parameters between conventional scanography and EOS in patients with advanced knee osteoarthritis who need surgical treatment.

Methods

A total of 52 consecutive patients (104 knees) with bilateral knee osteoarthritis of advanced stage (Kellgren-Lawrence [KL] grade 3 or 4) were retrospectively reviewed. We measured the hip-knee-ankle angle (HKA) on conventional scanograms. In EOS, we measured HKA, hip-knee-shaft angle, mechanical lateral distal femoral angle, and mechanical medial proximal tibial angle. To evaluate sagittal and axial plane alignment, knee flexion angle (KFA), and knee joint rotation (KJR) were also measured.

Results

Ninety knees were KL grade 4, and 14 knees were grade 3. The average HKA was 10.14° ± 6.16° on conventional scanograms and 11.26° ± 6.21° in EOS. HKA was greater in EOS than on conventional scanograms, and the difference (1.12°; range, −1.07° to 3.22°) was statistically significant (p < 0.001). Significant correlations were observed on the difference in HKA and mechanical medial proximal tibial angle (r = –0.198, p = 0.044), KFA (r = 0.193, p = 0.049), and KJR (r = 0.290, p = 0.003). In multivariable linear regression analysis, the difference in HKA had significant relationship with KFA (β = 0.286, p = 0.003) and KJR (β = 0.363, p < 0.001).

Conclusions

HKA measured on conventional scanograms and in EOS differed significantly and the difference had a significant correlations with KFA, KJR, and medial proximal tibial angle. Surgeons can consider these results before orthopedic surgery in patients who have advanced knee osteoarthritis.

Evaluation of the reliability of lower extremity alignment measurements using EOS imaging system while standing in an even weight-bearing posture

This study aimed to analyze the reproducibility and reliability of the alignment parameters measured using the EOS image system in both limbs while standing with an even weight-bearing posture. Overall, 104 lower extremities in 52 patients were analyzed retrospectively. The patients stood with an even load over both lower extremities then rotated 15° in both directions. Two EOS images were acquired and 104 pairs of lower extremities were compared according to the position of the indexed lower extremities. Then, the inter-observer reliability of the EOS system and the inter-modality reliability between EOS and computed tomography (CT) were evaluated. Femoro-tibial rotation (FTR) and tibial torsion demonstrated a significant difference between the anterior and posterior positions of the indexed lower extremity. In the inter-observer reliability analysis, all values except for FTR and tibial torsion demonstrated good or very good reliability. In the anterior position, FTR demonstrated moderate, and tibial torsion demonstrated poor reliability. In the posterior position, both FTR and tibial torsion demonstrated poor reliability. In the reliability analysis between the three-dimensional (3D) EOS model and 3D CT images, all measurements of the femur demonstrated very good reliability, but measurements of the tibia did not. For the coronal and sagittal alignment parameters measured by the EOS 3D system with rotated standing posture, except for the measurement including tibial torsion., there were no significant difference for either position of the indexed extremities with high agreement between the observers as well as with the CT 3D model.

Derotational Osteotomy of the Distal Femur for the Treatment of Patellofemoral Instability Simultaneously Leads to the Correction of Frontal Alignment: A Laboratory Cadaveric Study

Background:

Derotational osteotomy of the distal femur allows the anatomic treatment of patellofemoral maltracking due to increased femoral antetorsion. However, such rotational osteotomy procedures have a high potential of intended/unintended changes of frontal alignment.

Purpose/Hypothesis:

The purpose of this study was to perform derotational osteotomy of the distal femur and to demonstrate the utility of a novel trigonometric approach to address 3-dimensional (3D) changes on 2-dimensional imaging (axial computed tomography [CT] and frontal-plane radiography). The hypothesis was that 1-step single-cut osteotomy can simultaneously correct torsion and frontal alignment based on preoperatively calculated cutting angles.

Study Design:

Controlled laboratory study.

Methods:

Eight human cadaveric whole legs (4 lower limb torsos) underwent derotational osteotomy of the distal femur of 20°. A straight leg axis, determined as a mechanical femorotibial angle (mFTA) of 0°, was chosen as a goal for postoperative frontal alignment. The inclination of the cutting angle from the lateral view was calculated individually for each cadaveric leg and was represented by a simple 3D-printed cutting guide for surgery. Specimens underwent CT for the measurement of torsion, while the frontal leg axis was determined on an upright radiograph preoperatively and postoperatively. Preoperative and postoperative angles were compared with the mathematical prediction model.

Results:

The preoperative mFTA ranged from –3.9° (valgus) to +3.4° (varus) (mean, –0.2° ± 2.6°). A postoperative mean mFTA of 0.37° ± 0.69° (95% CI, –0.22° to 0.95°) was achieved (P = .01). Derotation showed a mean of 19.1° ± 2.1° (95% CI, 17.3°-20.8°). The oblique cutting plane for the correction of valgus legs showed a mean of 5.9° ± 6.8° and, for the correction of varus legs, a mean of –10.0° ± 4.5° projected on the perpendicular plane to the virtual anatomic shaft axis from the sagittal view.

Conclusion:

Single-cut distal femoral osteotomy can be performed to simultaneously address rotational as well as frontal alignment using a preoperatively defined oblique cut, as determined by the presented reproducible calculation model.

Clinical Relevance:

This study adds important knowledge to the technique of derotational osteotomy. This approach provides an individual, oblique single cut for the correction of torsion and frontal axis within a clinically insignificant margin. Simplified tables for calculation and a surgical reference make this model reproducible and safe.