Influence of the Prosthetic Index Into Morse Taper Implants on Bacterial Microleakage

Does the index in Morse taper connection affect the abutment stability? An in vitro experimental study

The present study compared three different implant and abutment sets of type Morse taper (MT) connection, with- and without-index, were analyzed regarding their mechanical behavior without and with cyclic load application simulating the masticatory function. Ninety implant and abutment (IA) sets were used in the present study, divided into three groups (n = 30 samples per group): Group A, Ideale solid straight abutment (one piece) without index; Group B, Ideale abutment with an angle of 30-degree (two pieces) without index; Group C, Ideale abutment with an angle of 30-degree (two pieces) with index. The abutment stability quotient (ASQ) values, detorque value and rotation angle were measured before and after the cycling load. Twenty IA sets of each group were submitted to mechanical load at 360,000 cycles. The ASQ without load were 64.7 ± 2.49 for the group A, 60.2 ± 2.64 for the group B, 54.4 ± 3.27 for the group C; With load were 66.1 ± 5.20 for the group A, 58.5 ± 6.14 for the group B, 58.9 ± 2.99 for the group C. Detorque values were lower in groups B and C compared to group A (p < 0.05). In conclusion, the presence of the index did not influence the stability values. However, solid straight abutments (group A) showed higher values of stability compared to groups of angled abutments (groups B and C).

The mechanical and clinical influences of prosthetic index structure in Morse taper implant-abutment connection: a scoping review

AIM

The implant-abutment connection is a crucial factor in determining the long-term stability of dental implants. The use of a prosthetic index structure in the Morse taper implant-abutment connection has been proposed as a potential solution to improve the accuracy of this connection. This study aimed to provide a scoping review of the mechanical and clinical effects of the prosthetic index structure in the Morse taper implant-abutment connection.

METHODS

A systematic scoping review of articles related to "dental implants," "Morse taper," and "index" was conducted using PubMed/MEDLINE, Web of Science, Cochrane, and Scopus databases, as well as a comprehensive literature search by two independent reviewers. Relevant articles were selected for analysis and discussion, with a specific focus on investigating the impact of prosthetic index structure on the mechanical and clinical aspects of Morse taper implant-abutment connections.

RESULTS

Finally, a total of 16 articles that met the inclusion criteria were included for data extraction and review. In vitro studies have demonstrated that the use of a prosthetic index structure in the Morse taper implant-abutment connection can affect stress distribution, biomechanical stability, and reverse torque values, which may reduce stress within cancellous bone and help limit crestal bone resorption. However, retrospective clinical studies have shown that this structure is also associated with a higher risk of mechanical complications, such as abutment fracture and abutment screw loosening.

CONCLUSIONS

Therefore, the clinical trade-off between preventing crestal bone resorption and mechanical complications must be carefully considered when selecting appropriate abutments. The findings suggest that this structure can improve the accuracy and stability of the implant-abutment connection, but its use should be carefully evaluated in clinical practice.

Bacterial infiltration and detorque at the implant abutment morse taper interface after masticatory simulation

This study evaluated the bacterial infiltration and the detorque of indexed and non-indexed abutments of Morse taper implants (MTI) after mechanical cycling (MC). 40 MTI were distributed into four groups: IIA (indexed implant abutments); NIIA (non-indexed implant abutments); IIAMC (indexed implant abutments submitted to MC); NIIAMC (non-indexed implant abutments submitted to MC), which were carried out under one million 5 Hz frequency and 3 Bar pressure. After mechanical cycling, all groups were immersed in a bacterial solution in Brain Heart Infusion Agar. After detorque, the bacteria infiltration was evaluated by counting the colony-forming units. For the bacterial infiltration, analysis was applied to the Kruskal-Wallis test (p = 0.0176) followed by Dunn's test. For the detorque analysis, the two-way repeated-measures ANOVA was applied, followed by the Tukey's test (p < 0.0001). Bacteria infiltration was highly observed in NIIA (p = 0.0027) and were absent in IIAMC and NIIAMC. The detorque values for IIA (19.96Ncm ± 0.19Ncm), NIIA (19.90Ncm ± 0.83Ncm), and NIIAMC (19.51Ncm ± 0,69Ncm) were similar and remained close to the initial value, while IIAMC (55.2Ncm ± 2.36Ncm) showed an extremely significant torque value increase (p < 0.0001). The mechanical cycling resulted in mechanical sealing of the implant-abutment interface, preventing bacterial infiltration in the indexed and non-indexed specimens, and increasing the detorque strength in the group of indexed abutments.

Effect of the prosthetic index on stress distribution in Morse taper connection implant system and peri-implant bone: a 3D finite element analysis

Background

The combination of a prosthetic index with Morse taper connection was developed, with the purpose of making prosthetic procedures more precise. However, the presence of the index may compromise the mechanical performance of the abutment. The aim of this study is to evaluate the effect of prosthetic index on stress distribution in implant–abutment-screw system and peri-implant bone by using the 3D finite element methodology.

Methods

Two commercial dental implant systems with different implant–abutment connections were used: the Morse taper connection with platform switching (MT-PS) implant system and the internal hex connection with platform matching (IH-PM) implant system. Meanwhile, there are two different designs of Morse taper connection abutment, namely, abutments with or without index. Consequently, three different models were developed and evaluated: (1) MT-PS indexed, (2) MT-PS non-indexed, and (3) IH-PM. These models were inserted into a bone block. Vertical and oblique forces of 100 N were applied to each abutment to simulate occlusal loadings.

Results

For the MT-PS implant system, the maximum stress was always concentrated in the abutment neck under both vertical and oblique loading. Moreover, the maximum von Mises stress in the neck of the MT-PS abutment with index even exceed the yield strength of titanium alloy under the oblique loading. For the IH-PM implant system, however, the maximum stress was always located at the implant. Additionally, the MT-PS implant system has a significantly higher stress level in the abutment neck and a lower stress level around the peri-implant bone compared to the IH-PM implant system. The combined average maximum stress from vertical and oblique loads is 2.04 times higher in the MT-PS indexed model, and 1.82 times for the MT-PS non-indexed model than that of the IH-PM model.

Conclusions

MT-PS with index will cause higher stress concentration on the abutment neck than that of without index, which is more prone to mechanical complications. Nevertheless, MT-PS decreases stress within cancellous bone and may contribute to limiting crestal bone resorption.

Effectiveness of Different Antimicrobial Agents on Malodor Prevention in Two-Stage Dental Implants: A Double-Blinded Randomized Clinical Trial

OBJECTIVE

 Opening of a healing abutment in two-stage implant systems is usually followed by a bad smell. Previous studies have found that presence of bacteria in microleakages of the implant-abutment interface results in further malodor. However, studies focusing on preventive treatments for this issue are scarce. Therefore, the aim of this study is to evaluate the effectiveness of two antimicrobial agents on prevention of malodor followed by opening the healing abutments.

MATERIALS AND METHODS

 Current double-blinded randomized clinical trial was performed on 51 eligible patients who were referred for their exposure surgery. They were divided equally into three parallel groups. In two groups, either chlorhexidine or tetracycline was added to the internal surface of the fixtures before screwing the healing abutments. One group did not receive any intervention. Three to 4 weeks later malodor was scored by sniffing the healing abutments immediately after uncovering them (odorless = 0/odor = 1). The three groups were then compared regarding malodor scores.

RESULTS

 Our findings showed that malodor was more frequent in the control group (58.82%) in comparison with groups of intervention (17.65 and 23.53%). There was a statistically significant difference between malodor in patients in whom antimicrobial agents (chlorhexidine and tetracycline) were used in their implants and the control group (p-value = 0.023). However, malodor in the chlorhexidine group and tetracycline group did not show any significant difference (p-value = 1).

CONCLUSION

 Based upon the data from this study, it appears that local antimicrobial agents including chlorhexidine and tetracycline result in less malodor production within the implant-abutment interface.

CLINICAL SIGNIFICANCE

 A specific type of malodor is commonly seen after opening the healing abutment of a two-stage dental implant. Not only this issue is noticed by the dentist, but also annoyed the patient. Using local antimicrobial agents in the fixtures is likely to be a simple, easily applicable solution that satisfies both patients and dentists, and eliminates the possibility of further inflammation.

Effect of Implant-Abutment Connection Type on Bone Around Dental Implants in Long-Term Observation: Internal Cone Versus Internal Hex

PURPOSE

The purpose of this study was to evaluate the influence of the implant-abutment connection type on the bone level around dental implants in long-term observation and the survival rate for the different types of implant-abutment connections.

MATERIALS AND METHODS

Two groups of implants made of titanium grade 23 alloy and with sandblasted and acid-etched (SLA) surface were included in the study: (a) the internal hex implant-abutment connection group (480 SPI dental implants; Alpha-Bio Tec, Petach Tikwa, Israel, 184 patients) and (b) the internal cone implant-abutment connection group (60 C1 dental implants; MIS Implant Technologies, Shlomi, Israel, 34 patients). Certain inclusion and exclusion criteria were applied. Marginal bone loss (MBL) around the dental implants was measured in intraoral radiographs taken with parallel technique with a film holder and by bite recording index. X-rays were performed at the moment of functional loading, and at 12, 24, 36, and 60 months after loading. The digital analysis was conducted using Dental Studio 2.0 computer software.

RESULTS

Average MBL was significantly lower in the conical connection compared with internal hex group-0.68 ± 0.59 versus 0.99 ± 0.89 mm (12 months), 0.78 ± 0.80 versus 1.12 ± 1.00 mm (24 months), 0.83 ± 0.87 versus 1.22 ± 1.03 mm (36 months), and 0.96 ± 1.02 versus 1.30 ± 1.15 mm (60 months after loading). Both groups of implants achieved a 100% survival rate.

CONCLUSION

The internal cone connection reduced bone resorption compared with the internal hex. Both groups of implants had a 100% survival rate.

Microleakage at the Different Implant Abutment Interface: A Systematic Review

INTRODUCTION

Presence of gap at the implant-abutment interface, leads to microleakage and accumulation of bacteria which can affect the success of dental implants.

AIM

To evaluate the sealing capability of different implant connections against microleakage.

MATERIALS AND METHODS

In January 2017 an electronic search of literature was performed, in Medline, EBSCO host and Pubmed data base. The search was focused on ability of different implant connections in preventing microleakage. The related titles and abstracts available in English were screened, and the articles that fulfilled the inclusion criteria were selected for full text reading.

RESULTS

In this systematic review, literature search initially resulted in 78 articles among which 30 articles only fulfilled the criteria for inclusion and were finally included in the review. Almost all the studies showed that there was some amount of microleakage at abutment implant interface. Microleakage was very less in Morse taper implants in comparison to other implant connections. Majority of studies showed less microleakage in static loading conditions and microleakage increases in dynamic loading conditions.

CONCLUSION

In this systematic review maximum studies showed that there was some amount of microleakage at abutment implant interface. External hexagon implants failed completely to prevent microleakage in both static and dynamic loading conditions of implants. Internal hexagon implants mainly internal conical (Morse taper) implants are very promising in case of static loading and also showed less microleakage in dynamic loading conditions. Torque recommended by manufacturer should be followed strictly to get a better seal at abutment implant interface. Zirconia abutments are more to microleakage than Titanium abutments and there use should be discouraged. Zirconia abutments should be only restricted to cases where there was very high demand of aesthetics.

In Vitro Microbiological Analysis of Bacterial Seal in Hybrid Zirconia Abutment Tapered Connection

PURPOSE

The aim of this study was to evaluate the bacterial seal at the implant-hybrid zirconia abutment interface and Morse taper-type connections through in vitro microbiological analysis.

MATERIALS AND METHODS

Sixteen implants and their respective abutments were divided into 3 groups: test (10 sets), positive control (3 sets), and negative control (3 sets). In the test group, 10 implants were contaminated with Escherichia coli using a sterile inoculating loop to the inner portion of the implants, followed by torque application to the abutment (30 N·cm). The positive controls were also contaminated, but no torque was applied to the abutment screw. The negative control consisted of uncontaminated sets. All specimens were immersed in test tubes containing 5 mL brain heart infusion (BHI) broth, maintained in a microbiological incubator for 14 days at 37°C under aerobic conditions, and monitored every 24 hours for evidence of bacterial growth.

RESULTS

During the 14 days of incubation, no significant increase in the number of cloudy culture media was observed in the test group (P = 0.448). No significant difference in broth turbidity ratio was observed (P > 0.05).

CONCLUSION

Hybrid zirconia abutments can create an effective seal at the tapered abutment-implant interface with a 30-N·cm installation torque.