Regression Estimates of Pressure on Transtibial Residual Limbs Using Load Cell Measurements of the Forces and Moments Occurring at the Base of the Socket

The biomechanical influence of transtibial Bone-Anchored limbs during walking

Individuals with unilateral transtibial amputation (TTA) using socket prostheses demonstrate asymmetric joint biomechanics during walking, which increases the risk of secondary comorbidities (e.g., low back pain (LBP), osteoarthritis (OA)). Bone-anchored limbs are an alternative to socket prostheses, yet it remains unknown how they influence multi-joint loading. Our objective was to determine the influence of bone-anchored limb use on multi-joint biomechanics during walking. Motion capture data (kinematics, ground reaction forces) were collected during overground walking from ten participants with unilateral TTA prior to (using socket prostheses) and 12-months after bone-anchored limb implantation. Within this year, each participant completed a rehabilitation protocol that guided progression of loading based on patient pain response and optimized biomechanics. Musculoskeletal models were developed at each testing timepoint (baseline or 12-months after implantation) and used to calculate joint kinematics, internal joint moments, and joint reaction forces (JRFs). Analyses were performed during three stance periods on each limb. The between-limb normalized symmetry index (NSI) was calculated for joint moments and JRF impulses. Discrete (range of motion (ROM), impulse NSI) dependent variables were compared before and after implantation using paired t-tests with Bonferroni-Holm corrections while continuous (ensemble averages of kinematics, moments, JRFs) were compared using statistical parametric mapping (p < 0.05). When using a bone-anchored limb, frontal plane pelvic (residual: pre = 9.6 ± 3.3°, post = 6.3 ± 2.5°, p = 0.004; intact: pre = 10.2 ± 3.9°, post = 7.9 ± 2.6°, p = 0.006) and lumbar (residual: pre = 15.9 ± 7.0°, post = 10.6 ± 2.5°, p = 0.024, intact: pre = 17.1 ± 7.0°, post = 11.4 ± 2.8°, p = 0.014) ROM was reduced compared to socket prosthesis use. The intact limb hip extension moment impulse increased (pre = -11.0 ± 3.6 Nm*s/kg, post = -16.5 ± 4.4 Nm*s/kg, p = 0.005) and sagittal plane hip moment impulse symmetry improved (flexion: pre = 23.1 ± 16.0 %, post = -3.9 ± 19.5 %, p = 0.004, extension: pre = 29.2 ± 20.3 %, post = 8.7 ± 22.9 %, p = 0.049). Residual limb knee extension moment impulse decreased compared to baseline (pre = 15.7 ± 10.8 Nm*s/kg, post = 7.8 ± 3.9 Nm*s/kg, p = 0.030). These results indicate that bone-anchored limb implantation alters multi-joint biomechanics, which may impact LBP or OA risk factors in the TTA population longitudinally.

Next-generation devices to diagnose residuum health of individuals suffering from limb loss: A narrative review of trends, opportunities, and challenges

OBJECTIVES

There is a need for diagnostic devices that can assist prosthetic care providers to better assess and maintain residuum health of individuals suffering from neuromusculoskeletal dysfunctions associated with limb loss. This paper outlines the trends, opportunities, and challenges that will facilitate the development of next-generation diagnostic devices.

DESIGN

Narrative literature review.

METHODS

Information about technologies suitable for integration into next-generation diagnostic devices was extracted from 41 references. We considered the invasiveness, comprehensiveness, and practicality of each technology subjectively.

RESULTS

This review highlighted a trend toward future diagnostic devices of neuromusculoskeletal dysfunctions of the residuum capable to support evidence-based patient-specific prosthetic care, patient empowerment, and the development of bionic solutions. This device should positively disrupt the organization healthcare by enabling cost-utility analyses (e.g., fee-for-device business models) and addressing healthcare gaps due to labor shortages. There are opportunities to develop wireless, wearable and noninvasive diagnostic devices integrating wireless biosensors to measure change in mechanical constraints and topography of residuum tissues during real-life conditions as well as computational modeling using medical imaging and finite element analysis (e.g., digital twin). Developing the next-generation diagnostic devices will require to overcome critical barriers associated with the design (e.g., gaps between technology readiness levels of essential parts), clinical roll-out (e.g., identification of primary users), and commercialization (e.g., limited interest from investors).

CONCLUSIONS

We anticipate that next-generation diagnostic devices will contribute to prosthetic care innovations that will safely increase mobility, thereby improving the quality of life of the growing global population of individuals suffering from limb loss.

A proper sequence of dynamic alignment in transtibial prosthesis: insight through socket reaction moments

Dynamic alignment in prosthetic fitting is important because it affects the user's stability, kinematics, and kinetics such as socket reaction moments. It is performed by tuning the spatial relationship between the transtibial prosthetic socket and the foot following sequential observational gait analysis in the three anatomical planes. However, the order of planes in which the adjustment should be performed is still unclear. To investigate the appropriate sequence of dynamic alignment adjustment, ten participants with transtibial amputation were asked to walk in different alignment conditions (flexion, extension, adduction, abduction; lateral, medial, anterior, and posterior translation of the socket, and plantarflexion, dorsiflexion, inversion, and eversion of the foot) to measure socket reaction moments in the out-of-planes (e.g., the effect of sagittal alignment on the coronal moment). A significant difference was found only among socket posterior translation, socket flexion, and baseline alignment in the coronal moment (P = 0.02). The results of the current and previous studies suggest that moments in the coronal plane are affected by alignment changes in all three planes, whereas moments in the sagittal plane are affected only by sagittal alignment changes. It is suggested that the procedure of alignment adjustments should be finalized in the coronal plane.

Angulation vs translation of transtibial prosthetic socket: their difference analyzed by socket reaction moments

BACKGROUND

Previous studies investigated the effects of alignment changes in transtibial prostheses on socket reaction moments. However, the effects of angular and translational alignment changes with equal displacement between the foot and the socket were not directly compared.

RESEARCH QUESTIONS

What are the different effects of angular and translational alignment changes in transtibial prostheses?

METHODS

Ten individuals with transtibial prostheses participated in the measurement of temporo-spatial parameters, socket reaction moments, and their timings under nine alignment conditions (3° flexion/extension, anterior/posterior translation, 6° adduction/abduction, medial/lateral translation, and baseline). The displacement of the prosthetic feet was set to be equal between the angular and translational changes.

RESULTS

No significant changes in walking speed were found. Similar effects were observed in the magnitudes, but not in timing, of the moments under angular and translational changes in the sagittal plane (p < 0.01 for the differences in peak extension moment among anterior translation, baseline, and extension conditions, and in peak flexion moment among anterior translation, baseline, and extension conditions). In the coronal plane, similar effects were found in the magnitudes of the moments in the early stance (p < 0.01 at 5 %, 20 %, and 75 % stance). A significant difference in magnitude was observed in the late stance (p < 0.01 between adduction and medial translation conditions).

SIGNIFICANCE

The timing of the socket reaction moment may be different in the sagittal plane, while the magnitudes of the socket reaction moment in the late stance may be different in the coronal plane between the angular and translational alignment changes.

Predictive Control for an Active Prosthetic Socket informed by FEA-based Tissue Damage Risk Estimation

This paper presents an architecture for generalized predictive control for an active prosthetic socket system, based on a cost function performance index measure for minimization of residual limb tissue injury. Finite element analysis of a transtibial residuum model donned with a total surface bearing socket was used to provide controller training data and biomechanical rationale for deep tissue injury risk assessment, by estimating the internal deformation state of the soft tissues and the residuum-socket interface loading under a range of prosthetic loading instances. The results demonstrate the concept of this approach for interface actuation modelled as translational spring and damper systems.

Kinetics of Lower Limb Prosthesis: Automated Detection of Vertical Loading Rate

Vertical loading rate could be associated with residuum and whole body injuries affecting individuals fitted with transtibial prostheses. The objective of this study was to outline one out of five automated methods of extraction of vertical loading rate that stacked up the best against manual detection, which is considered the gold standard during pseudo-prosthetic gait. The load applied on the long axis of the leg of three males was recorded using a transducer fitted between a prosthetic foot and physiotherapy boot while walking on a treadmill for circa 30 min. The automated method of extraction of vertical loading rate, combining the lowest absolute average and range of 95% CI difference compared to the manual method, was deemed the most accurate and precise. The average slope of the loading rate detected manually over 150 strides was 5.56 ± 1.33 kN/s, while the other slopes ranged from 4.43 ± 0.98 kN/s to 6.52 ± 1.64 kN/s depending on the automated detection method. An original method proposed here, relying on progressive loading gradient-based automated extraction, produced the closest results (6%) to manual selection. This work contributes to continuous efforts made by providers of prosthetic and rehabilitation care to generate evidence informing reflective clinical decision-making.

Automated characterization of anthropomorphicity of prosthetic feet fitted to bone-anchored transtibial prosthesis

OBJECTIVE

This study describes differentiating prosthetic feet designs fitted to bone-anchored transtibial prostheses based on an automated characterization of ankle stiffness profile relying on direct loading measurements. The objectives were (A) to present a process characterizing stiffness using innovative macro, meso and micro analyses, (B) to present stiffness profiles for feet with and without anthropomorphic designs, where anthropomorphicity is defined as a similarity of the moment-angle dependency in prosthetic and in the anatomical ankle, (C) to determine sensitivity of characterization.

METHODS

Three participants walked consecutively with two instrumented bone-anchored prostheses including their own prosthetic feet and Free-Flow foot meeting the anthropomorphicity criterion by design. Angle of dorsiflexion was extracted from video footage. Bending moment was recorded using multi-axis transducer attached to osseointegrated fixation. The automated characterization of stiffness involved a 12-step process relying on data-based criterion.

RESULTS

The meso analyses confirmed bilinear behavior of moment-angle curves with Index of Anthropomorphicity of -2.966±2.369 Nm/Deg and 2.681±1.089 Nm/Deg indicating a convex and concave shape of usual and Free-Flow feet without and with anthropomorphic designs, respectively.

CONCLUSIONS

The proposed straightforward meso analysis of the stiffness was capable to report clinical meaningful differences sensitive to feet's anthropomorphicity. Results confirmed the benefits for clinicians to rely on direct loading measurement providing individualized complementary insight into impact of components.

SIGNIFICANCE

This work could assist the developments of standards and guidelines for manufacturing and safe fitting of components to growing population requiring transtibial prostheses with socket or direct skeletal attachment worldwide.

An Inductive Sensing System to Measure In-Socket Residual Limb Displacements for People Using Lower-Limb Prostheses

The objective of this research was to assess the performance of an embedded sensing system designed to measure the distance between a prosthetic socket wall and residual limb. Low-profile inductive sensors were laminated into prosthetic sockets and flexible ferromagnetic targets were created from elastomeric liners with embedded iron particles for four participants with transtibial amputation. Using insights from sensor performance testing, a novel calibration procedure was developed to quickly and accurately calibrate the multiple embedded sensors. The sensing system was evaluated through laboratory tests in which participants wore sock combinations with three distinct thicknesses and conducted a series of activities including standing, walking, and sitting. When a thicker sock was worn, the limb typically moved further away from the socket and peak-to-peak displacements decreased. However, sensors did not measure equivalent distances or displacements for a given sock combination, which provided information regarding the fit of the socket and how a sock change intervention influenced socket fit. Monitoring of limb⁻socket displacements may serve as a valuable tool for researchers and clinicians to quantitatively assess socket fit.

An investigation on effects of amputee's physiological parameters on maximum pressure developed at the prosthetic socket interface using artificial neural network

Technological advances in prosthetics have attracted the curiosity of researchers in monitoring design and developments of the sockets to sustain maximum pressure without any soft tissue damage, skin breakdown, and painful sores. Numerous studies have been reported in the area of pressure measurement at the limb/socket interface, though, the relation between amputee's physiological parameters and the pressure developed at the limb/socket interface is still not studied. Therefore, the purpose of this work is to investigate the effects of patient-specific physiological parameters viz. height, weight, and stump length on the pressure development at the transtibial prosthetic limb/socket interface. Initially, the pressure values at the limb/socket interface were clinically measured during stance and walking conditions for different patients using strain gauges placed at critical locations of the stump. The measured maximum pressure data related to patient's physiological parameters was used to develop an artificial neural network (ANN) model. The effects of physiological parameters on the pressure development at the limb/socket interface were examined using the ANN model. The analyzed results indicated that the weight and stump length significantly affects the maximum pressure values. The outcomes of this work could be an important platform for the design and development of patient-specific prosthetic socket which can endure the maximum pressure conditions at stance and ambulation conditions.

A finite element model to assess transtibial prosthetic sockets with elastomeric liners

People with transtibial amputation often experience skin breakdown due to the pressures and shear stresses that occur at the limb-socket interface. The purpose of this research was to create a transtibial finite element model (FEM) of a contemporary prosthesis that included complete socket geometry, two frictional interactions (limb-liner and liner-socket), and an elastomeric liner. Magnetic resonance imaging scans from three people with characteristic transtibial limb shapes (i.e., short-conical, long-conical, and cylindrical) were acquired and used to develop the models. Each model was evaluated with two loading profiles to identify locations of focused stresses during stance phase. The models identified five locations on the participants' residual limbs where peak stresses matched locations of mechanically induced skin issues they experienced in the 9 months prior to being scanned. The peak contact pressure across all simulations was 98 kPa and the maximum resultant shear stress was 50 kPa, showing reasonable agreement with interface stress measurements reported in the literature. Future research could take advantage of the developed FEM to assess the influence of changes in limb volume or liner material properties on interface stress distributions. Graphical abstract Residual limb finite element model. Left: model components. Right: interface pressures during stance phase.

Systematic Review of Studies Examining Transtibial Prosthetic Socket Pressures with Changes in Device Alignment

Suitable lower-limb prosthetic sockets must provide an adequate distribution of the pressures created from standing and ambulation. A systematic search for articles reporting socket pressure changes in response to device alignment perturbation was carried out, identifying 11 studies. These were then evaluated using the American Academy of Orthotists and Prosthetists guidelines for a state-of-the-science review. Each study used a design where participants acted as their own controls. Results were available for 52 individuals and five forms of alignment perturbation. Four studies were rated as having moderate internal and external validity, the remainder were considered to have low validity. Significant limitations in study design, reporting quality and in representation of results and the suitability of calculations of statistical significance were evident across articles. Despite the high inhomogeneity of study designs, moderate evidence supports repeatable changes in pressure distribution for specific induced changes in component alignment. However, there also appears to be a significant individual component to alignment responses. Future studies should aim to include greater detail in the presentation of results to better support later meta-analyses.

Socket reaction moments in transtibial prostheses during walking at clinically perceived optimal alignment

BACKGROUND AND AIM

The socket reaction moments are directly measured at the base of a socket and may be useful for fitting a prosthesis. Previous studies have focused on the effect of prosthetic alignment changes on them. The aim of this study was to explore their range at clinically perceived optimal alignment by investigating the individual differences.

TECHNIQUE

In total, 11 amputees using unilateral transtibial prostheses with solid-ankle-cushion-heel (SACH) feet were recruited. The socket reaction moments were measured using a custom instrumented prosthesis alignment component and plotted. Eight variables that were related to their magnitude (N m/kg) and timing (% stance of event) as well as cadence (steps/minute) were calculated for each amputee. Their mean, standard deviation, maximum value, minimum value, and range were subsequently analyzed.

DISCUSSION

This study may serve as a foundation to explore the range of individual differences in socket reaction moments in transtibial prostheses.

CLINICAL RELEVANCE

Socket reaction moments can be conveniently measured in the clinical setting. Prosthetists could potentially use them as one of the criteria to align prosthesis in addition to observational gait analysis and amputees perception.

Effect of alignment changes on socket reaction moments while walking in transtibial prostheses with energy storage and return feet

BACKGROUND

Energy storage and return feet are designed for active amputees. However, little is known about the socket reaction moments in transtibial prostheses with energy storage and return feet. The aim of this study was to investigate the effect of alignment changes on the socket reaction moments during gait while using the energy storage and return feet.

METHODS

A Smart Pyramid™ was used to measure the socket reaction moments in 10 subjects with transtibial prostheses while walking under 25 alignment conditions, including a nominal alignment (as defined by conventional clinical methods), as well as angle malalignments of 2°, 4° and 6° (flexion, extension, abduction, and adduction) and translation malalignments of 5mm, 10mm and 15mm (anterior, posterior, lateral, and medial) referenced from the nominal alignment. The socket reaction moments of the nominal alignment were compared with each malalignment.

FINDINGS

Both coronal and sagittal alignment changes demonstrated systematic effects on the socket reaction moments. In the sagittal plane, angle and translation alignment changes demonstrated significant differences (P<0.05) in the minimum moment, the moment at 45% of stance and the maximum moment for some comparisons. In the coronal plane, angle and translation alignment changes demonstrated significant differences (P<0.05) in the moment at 30% and 75% of stance for all comparisons.

INTERPRETATION

The alignment may have systematic effects on the socket reaction moments in transtibial prostheses with energy storage and return feet. The socket reaction moments could potentially be a useful biomechanical parameter to evaluate the alignment of the transtibial prostheses.

Effect of alignment changes on socket reaction moments during gait in transfemoral and knee-disarticulation prostheses: case series

The alignment of a lower-limb prosthesis is critical to the successful prosthetic fitting and utilization by the wearer. Loads generated by the socket applied to the residual limb while walking are thought to be different in transfemoral and knee-disarticulation prostheses. The aim of this case series was to compare the socket reaction moments between transfemoral and knee-disarticulation prostheses and to investigate the effect of alignment changes on them. Two amputees, one with a transfemoral prosthesis and another with a knee-disarticulation prosthesis, participated in this study. A Smart Pyramid™ was used to measure socket reaction moments while walking under 9 selected alignment conditions; including nominally aligned, angle malalignments of 6° (flexion, extension, abduction and adduction) and translation malalignments of 15 mm (anterior, posterior, medial and lateral) of the socket relative to the foot. This study found that the pattern of the socket reaction moments was similar between transfemoral and knee-disarticulation prostheses. An extension moment in the sagittal plane and a varus moment in the coronal plane were dominant during stance under the nominally aligned condition. This study also demonstrated that alignment changes might have consistent effects on the socket reaction moments in transfemoral and knee-disarticulation prostheses. Extension and posterior translation of the socket resulted in increases in an extension moment, while abduction and lateral translation of the socket resulted in increases in a varus moment. The socket reaction moments may potentially serve as useful biomechanical parameters to evaluate alignment in transfemoral and knee-disarticulation prostheses.

Effect of alignment changes on sagittal and coronal socket reaction moment interactions in transtibial prostheses

Alignment is important for comfortable and stable gait of lower-limb prosthesis users. The magnitude of socket reaction moments in the multiple planes acting simultaneously upon the residual limb may be related to perception of comfort in individuals using prostheses through socket interface pressures. The aim of this study was to investigate the effect of prosthetic alignment changes on sagittal and coronal socket reaction moment interactions (moment-moment curves) and to characterize the curves in 11 individuals with transtibial amputation using novel moment-moment interaction parameters measured by plotting sagittal socket reaction moments versus coronal ones under various alignment conditions. A custom instrumented prosthesis alignment component was used to measure socket reaction moments during walking. Prosthetic alignment was tuned to a nominally aligned condition by a prosthetist, and from this position, angular (3° and 6° of flexion, extension, abduction or adduction of the socket) and translational (5mm and 10mm of anterior, posterior, medial or lateral translation of the socket) alignment changes were performed in either the sagittal or the coronal plane in a randomized manner. A total of 17 alignment conditions were tested. Coronal angulation and translation alignment changes demonstrated similar consistent changes in the moment-moment curves. Sagittal alignment changes demonstrated more complex changes compared to the coronal alignment changes. Effect of sagittal angulations and translations on the moment-moment curves was different during 2nd rocker (mid-stance) with extension malalignment appearing to cause medio-lateral instability. Presentation of coronal and sagittal socket reaction moment interactions may provide useful visual information for prosthetists to understand the biomechanical effects of malalignment of transtibial prostheses.