How Computational Modeling can Help to Predict Gas Transfer in Artificial Lungs Early in the Design Process

Computational Analysis of the Effects of Fiber Deformation on the Microstructure and Permeability of Blood Oxygenator Bundles

Mechanical loads on the polymeric fibers of oxygenating bundles are commonly present due to bundle press-fitting during device assembly and blood pressure load. However, computational fluid dynamics (CFD) simulations for fiber bundle optimization neglect possible changes in microstructure due to such deformations. The aim of this study is to investigate the impact of fiber deformability on bundle microstructure and fluid dynamics mainly in terms of permeability. Fibers from commercial mats typically used for blood oxygenators were mechanically tested and based on these experimental data, a material model was developed to simulate the structural deformations the fibers undergo under press-fitting and blood pressure loads. Then, CFD simulations were performed on deformed bundle repetitive units to investigate permeability under varying loading conditions. The effects of different bundle geometric parameters on the variation of bundle permeability due to press-fitting were evaluated. Bundle press-fitting results in significant changes in microstructure that are reflected in a bundle permeability more than halved for a 15% press-fitting. This impact on permeability is present in all the simulated fiber bundles and becomes more pronounced as the pitch between fibers and thus bundle porosity decreases. Instead, the analyses on pressurized bundle show only small deformations caused by pressure load, with permeability changes below 1%. While blood pressure effects could be neglected, bundle press-fitting turns out to have a significant impact on bundle microstructure and permeability. Neglecting such microstructure variations during CFD simulations could also lead to incorrect assessment of the local fluid dynamics within the bundle.

Novel Size-Variable Dedicated Rodent Oxygenator for ECLS Animal Models-Introduction of the "RatOx" Oxygenator and Preliminary In Vitro Results

The overall survival rate of extracorporeal life support (ECLS) remains at 60%. Research and development has been slow, in part due to the lack of sophisticated experimental models. This publication introduces a dedicated rodent oxygenator ("RatOx") and presents preliminary in vitro classification tests. The RatOx has an adaptable fiber module size for various rodent models. Gas transfer performances over the fiber module for different blood flows and fiber module sizes were tested according to DIN EN ISO 7199. At the maximum possible amount of effective fiber surface area and a blood flow of 100 mL/min, the oxygenator performance was tested to a maximum of 6.27 mL O₂/min and 8.2 mL CO₂/min, respectively. The priming volume for the largest fiber module is 5.4 mL, while the smallest possible configuration with a single fiber mat layer has a priming volume of 1.1 mL. The novel RatOx ECLS system has been evaluated in vitro and has demonstrated a high degree of compliance with all pre-defined functional criteria for rodent-sized animal models. We intend for the RatOx to become a standard testing platform for scientific studies on ECLS therapy and technology.

Trends, Advantages and Disadvantages in Combined Extracorporeal Lung and Kidney Support From a Technical Point of View

Extracorporeal membrane oxygenation (ECMO) provides pulmonary and/or cardiac support for critically ill patients. Due to their diseases, they are at high risk of developing acute kidney injury. In that case, continuous renal replacement therapy (CRRT) is applied to provide renal support and fluid management. The ECMO and CRRT circuits can be combined by an integrated or parallel approach. So far, all methods used for combined extracorporeal lung and kidney support present serious drawbacks. This includes not only high risks of circuit related complications such as bleeding, thrombus formation, and hemolysis, but also increase in technical workload and health care costs. In this sense, the development of a novel optimized artificial lung device with integrated renal support could offer important treatment benefits. Therefore, we conducted a review to provide technical background on existing techniques for extracorporeal lung and kidney support and give insight on important aspects to be addressed in the development of this novel highly integrated artificial lung device.

Three-dimensional membranes for artificial lungs: Comparison of flow-induced hemolysis

BACKGROUND

Membranes based on triply periodic minimal surfaces (TPMS) have proven a superior gas transfer compared to the contemporary hollow fiber membrane (HFM) design in artificial lungs. The improved oxygen transfer is attributed to disrupting the laminar boundary layer adjacent to the membrane surface known as main limiting factor to mass transport. However, it requires experimental proof that this improvement is not at the expense of greater damage to the blood. Hence, the aim of this work is a valid statement regarding the structure-dependent hemolytic behavior of TPMS structures compared to the current HFM design.

METHODS

Hemolysis tests were performed on structure samples of three different kind of TPMS-based designs (Schwarz-P, Schwarz-D and Schoen's Gyroid) in direct comparison to a hollow fiber structure as reference.

RESULTS

The results of this study suggest that the difference in hemolysis between TPMS membranes compared to HFMs is small although slightly increased for the TPMS membranes. There is no significant difference between the TPMS structures and the hollow fiber design. Nevertheless, the ratio between the achieved additional oxygen transfer and the additional hemolysis favors the TPMS-based membrane shapes.

CONCLUSION

TPMS-shaped membranes offer a safe way to improve gas transfer in artificial lungs.

Numerical modeling of pulsatile blood flow through a mini-oxygenator in artificial lungs

While previous in vitro studies showed divergent results concerning the influence of pulsatile blood flow on oxygen advection in oxygenators, no study was done to investigate the uncertainty affected by blood flow dynamics. The aim of this study is to utilize a computational fluid dynamics model to clarify the debate concerning the influence of pulsatile blood flow on the oxygen transport. The computer model is based on a validated 2D finite volume approach that predicts oxygen transfer in pulsatile blood flow passing through a 300-micron hollow-fiber membrane bundle with a length of 254 mm, a building block for an artificial lung device. In this study, the flow parameters include the steady Reynolds number (Re = 2, 5, 10 and 20), Womersley parameter (Wo = 0.29, 0.38 and 0.53) and sinusoidal amplitude (A = 0.25, 0.5 and 0.75). Specifically, the computer model is extended to verify, for the first time, the previously measured O₂ transport that was observed to be hindered by pulsating flow in the Biolung, developed by Michigan Critical Care Consultants. A comprehensive analysis is carried out on computed profiles and fields of oxygen partial pressure (P_O2) and oxygen saturation (S_O2) as a function of Re, Wo and A. Based on the present results, we observe the positive and negative effects of pulsatile flow on P_O2 at different blood flow rates. Besides, the S_O2 variation is not much influenced by the pulsatile flow conditions investigated. While being consistent with a recent experimental study, the computed O₂ volume flow rate is found to be increased at high blood flow rates operated with low frequency and high amplitude. Furthermore, the present study qualitatively explains that divergent outcomes reported in previous in vitro experimental studies could be owing to the different blood flow rates adopted. Finally, the contour analysis reveals how the spatial distributions of P_O2 and S_O2 vary over time.

Long-Term Venovenous Connection for Extracorporeal Carbon Dioxide Removal (ECCO2R)-Numerical Investigation of the Connection to the Common Iliac Veins

Purpose

Currently used cannulae for extracorporeal carbon dioxide removal (ECCO₂R) are associated with complications such as thrombosis and distal limb ischemia, especially for long-term use. We hypothesize that the risk of these complications is reducible by attaching hemodynamically optimized grafts to the patient’s vessels. In this study, as a first step towards a long-term stable ECCO₂R connection, we investigated the feasibility of a venovenous connection to the common iliac veins. To ensure its applicability, the drainage of reinfused blood (recirculation) and high wall shear stress (WSS) must be avoided.

Methods

A reference model was selected for computational fluid dynamics, on the basis of the analysis of imaging data. Initially, a sensitivity analysis regarding recirculation was conducted using as variables: blood flow, the distance of drainage and return to the iliocaval junction, as well as the diameter and position of the grafts. Subsequently, the connection was optimized regarding recirculation and the WSS was evaluated. We validated the simulations in a silicone model traversed by dyed fluid.

Results

The simulations were in good agreement with the validation measurements (mean deviation 1.64%). The recirculation ranged from 32.1 to 0%. The maximum WSS did not exceed 5.57 Pa. The position and diameter of the return graft show the highest influence on recirculation. A correlation was ascertained between recirculation and WSS. Overall, an inflow jet directed at a vessel wall entails not only high WSS, but also a flow separation and thereby an increased recirculation. Therefore, return grafts aligned to the vena cava are crucial.

Conclusion

In conclusion, a connection without recirculation could be feasible and therefore provides a promising option for a long-term ECCO₂R connection.