In vivo experimental testing of the FW axial blood pump for left ventricular support in Fu Wai Hospital

Ovine Leukocyte Microparticles Generated by the CentriMag Ventricular Assist Device In Vitro

Ventricular assist devices (VADs) are a life-saving form of mechanical circulatory support in heart failure patients. However, VADs have not yet reached their full potential due to the associated side effects (thrombosis, bleeding, infection) related to the activation and damage of blood cells and proteins caused by mechanical stress and foreign materials. Studies of the effects of VADs on leukocytes are limited, yet leukocyte activation and damage including microparticle generation can influence both thrombosis and infection rates. Therefore, the aim was to develop a multicolor flow cytometry assessment of leukocyte microparticles (LMPs) using ovine blood and the CentriMag VAD as a model for shear stress. Ovine blood was pumped for 6 h in the CentriMag and regular samples analyzed for hemolysis, complete blood counts and LMP by flow cytometry during three different pump operating conditions (low flow, standard, high speed). The high speed condition caused significant increases in plasma-free hemoglobin; decreases in total leukocytes, granulocytes, monocytes, and platelets; increases in CD45⁺ LMPs as well as two novel LMP populations: CD11b^bright /HLA-DR^- and CD11b^dull /HLA-DR⁺ , both of which were CD14^- /CD21^- . CD11b^bright /HLA-DR^- LMPs appeared to respond to an increase in shear magnitude whereas the CD11b^dull /HLA-DR⁺ LMPs significantly increased in all pumping conditions. We propose that these two populations are released from granulocytes and T cells, respectively, but further research is needed to better characterize these two populations.

Numerical and In Vitro Experimental Investigation of the Hemolytic Performance at the Off-Design Point of an Axial Ventricular Assist Pump

The ventricular assist pumps do not always function at the design point; instead, these pumps may operate at unfavorable off-design points. For example, the axial ventricular assist pump FW-2, in which the design point is 5 L/min flow rate against 100 mm Hg pressure increase at 8,000 rpm, sometimes works at off-design flow rates of 1 to 4 L/min. The hemolytic performance of the FW-2 at both the design point and at off-design points was estimated numerically and tested in vitro. Flow characteristics in the pump were numerically simulated and analyzed with special attention paid to the scalar sheer stress and exposure time. An in vitro hemolysis test was conducted to verify the numerical results. The simulation results showed that the scalar shear stress in the rotor region at the 1 L/min off-design point was 70% greater than at the 5 L/min design point. The hemolysis index at the 1 L/min off-design point was 3.6 times greater than at the 5 L/min design point. The in vitro results showed that the normalized index of hemolysis increased from 0.017 g/100 L at the 5 L/min design point to 0.162 g/100 L at the 1 L/min off-design point. The hemolysis comparison between the different blood pump flow rates will be helpful for future pump design point selection and will guide the usage of ventricular assist pumps. The hemolytic performance of the blood pump at the working point in the clinic should receive more focus.

Design and numerical evaluation of an axial partial-assist blood pump for Chinese and other heart failure patients

A fully implantable axial left ventricular assist device LAP31 was developed for Chinese or other heart failure patients who need partial support. Based on the 5-Lpm total cardiac blood output of Chinese without heart failure disease, the design point of LAP31 was set to a flow rate of 3 Lpm with 100-mmHg pressure head. To achieve the required pressure head and good hemolytic performance, a structure that includes a spindly rotor hub and a diffuser with splitter and cantilevered main blades was developed. Computational fluid dynamics (CFD) was used to analyze the hydraulic and hemodynamic performance of LAP31. Then in vitro hydraulics experiments were conducted. The numerical simulation results show that LAP31 could generate a 1 to 8 Lpm flow rate with a 60.9 to 182.7 mmHg pressure head when the pump was rotating between 9,000 and 12,000 rpm. The average scalar shear stress of the blood pump was 21.7 Pa, and the average exposure time was 71.0 milliseconds. The mean hemolysis index of LAP31 obtained using Heuser's hemolysis model and Giersiepen's model was 0.220% and 3.89 × 10-5% respectively. After adding the splitter blades, the flow separation at the suction surface of the diffuser was reduced. The cantilever structure reduced the tangential velocity from 6.1 to 4.7-1.4 m/s within the blade gap by changing the blade gap from shroud to hub. Subsequently, the blood damage caused by shear stress was reduced. In conclusion, the hydraulic and hemolytic characteristics of the LAP31 are acceptable for partial support.

Short-term in vivo preclinical biocompatibility evaluation of FW-II axial blood pump in a sheep model

We investigated the outcome of FW-II axial pump on healthy sheep (weight, 60-70 kg) for 2 weeks by perioperatively hematological and chemical tests, and circulating activated platelet and leukocyte-platelet aggregates measurements by flow cytometry assays. Complete necropsy and histopathological examinations and thorough pump inspection were performed at study termination for evidence of thrombi. In this experimental series, one sheep died of pulmonary edema, the other four sheep reached the scheduled endpoint of 14 days without device-related problems, and flow range was maintained at 2.5-4.0 L/min. The number of red blood cells and platelets decreased within first 3 days but increased gradually after the first postoperative week. In all animals, serum glutamic oxaloacetic transaminase increased significantly after surgery but gradually returned to normal limits within 2 weeks. Platelet activation, granulocyte-platelet aggregates, and monocyte-platelet aggregates reached the peak at postoperative day 2. Postexplant examinations indicated round thrombus in the hub areas of pumps. No evidence of ischemia or infarction was found in the explanted hearts, livers, spleens, kidneys, and brains of the five animals. Our results demonstrate that FW-II ventricular assist device (VAD) is a promising device for left ventricular (LV) support with moderate anticoagulation.

Computational fluid dynamics analysis of thrombosis potential in left ventricular assist device drainage cannulae

Cannulation is necessary when blood is removed from the body, for example in hemodialysis, cardiopulmonary bypass, blood oxygenators, and ventricular assist devices. Artificial blood contacting surfaces are prone to thrombosis, especially in the presence of stagnant or recirculating flow. In this work, computational fluid dynamics was used to investigate the blood flow fields in three clinically available cannulae (Medtronic DLP 12, 16, and 24 F), used as drainage for pediatric circulatory support and to calculate parameters that may be indicative of thrombosis potential. The results show that using the 24 F cannula below flow rates of about 0.75 L/min produces hemodynamic conditions, which may increase the risk of blood clotting within the cannula. No reasons are indicated for not using the 12 or 16 F cannulae with flow rates between 0.25 and 3.0 L/min.